# Espressif ESP32-S3-DevKitC-1-N8R8 v1.1

## Scope

This processed manufacturer user guide is the primary source for the Espressif ESP32-S3-DevKitC-1 v1.1 development board, with the N8R8 ordering code (ESP32-S3-WROOM-1-N8R8 module, PCB antenna). The board exposes two fixed 1x22, 2.54 mm header rows. It is not a bare ESP32-S3-WROOM land pattern.

## Board-specific implementation notes

- The v1.1 addressable RGB LED is driven by GPIO38. The initial/older board uses GPIO48 instead; do not mix those revisions.
- Espressif documents USB, 5V/GND header power, and 3V3/GND header power as mutually exclusive power paths unless the carrier intentionally manages source isolation.
- GPIO35, GPIO36, and GPIO37 are not externally available on Octal flash/PSRAM and WROOM-2 variants. They remain physical header pads on this carrier geometry but are unavailable for the selected N8R8 board's Octal memory configuration.
- The official v1.1 PCB layout gives a nominal board size of 25.40 mm x 62.74 mm, 2.54 mm header pitch, 22.86 mm row spacing, and an approximately 8.00 mm USB-side connector overhang.

## Source provenance

Manufacturer: Espressif Systems. Hardware revision: ESP32-S3-DevKitC-1 v1.1. Ordering code: ESP32-S3-DevKitC-1-N8R8. The complete source set is linked from the component record: the v1.1 user guide, schematic, PCB layout drawing, dimensions PDF/DXF, and Espressif's KiCad library.

## Extracted manufacturer guide

ESP32-S3
esp-dev-kits Documentation




                         Release master
                         Espressif Systems
                         Jul 02, 2026


---

Table of contents

Table of contents                                                                                              i

1 ESP32-S3-DevKitC-1                                                                                          3
  1.1 ESP32-S3-DevKitC-1 v1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .     3
      1.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .     3
      1.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      6
      1.1.3 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       9
      1.1.4 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       9

2 ESP32-S3-USB-OTG                                                                                            17
  2.1 ESP32-S3-USB-OTG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      17
      2.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .     17
      2.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      23
      2.1.3 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       29

3 ESP32-S3-LCD-EV-Board                                                                                       31
  3.1 ESP32-S3-LCD-EV-Board v1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .        31
      3.1.1 Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      31
      3.1.2 Start Application Development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       41
      3.1.3 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      41
      3.1.4 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       45
      3.1.5 Sample Request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      45
      3.1.6 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .       47

4 ESP-VoCat                                                                                                   65
  4.1 ESP-VoCat v1.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    65
       4.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    66
       4.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .     73
       4.1.3 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      78
       4.1.4 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      78

5 ESP-DualKey                                                                                                 91
  5.1 ESP-DualKey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   91
       5.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .    92
       5.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .     94
       5.1.3 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      95
       5.1.4 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .      95

6 EOL (End of Life) Boards                                                                                 97
  6.1 ESP32-S3-DevKitM-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
       6.1.1 ESP32-S3-DevKitM-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
  6.2 ESP32-S3-USB-Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
       6.2.1 ESP32-S3-USB-Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

7 Related Documentation and Resources                                                                        113
  7.1 Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
  7.2 Developer Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113



                                                                                                               i


---

     7.3   Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
     7.4   Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

8 Disclaimer and Copyright Notice                                                                                115




ii


---

Table of contents




This document provides detailed user guides and examples for ESP32-S3 series development boards.


Note: For the full list of Espressif development boards, please go to ESP DevKits.




Espressif Systems                                 1                                            Release master
                                       Submit Document Feedback


---

Table of contents




Espressif Systems              2               Release master
                    Submit Document Feedback


---

Chapter 1

ESP32-S3-DevKitC-1


The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, ESP32-S3-
WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® Low Energy MCU module that
integrates complete Wi-Fi and Bluetooth Low Energy functions.
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing.
Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard.


1.1     ESP32-S3-DevKitC-1 v1.1


The older version: ESP32-S3-DevKitC-1 v1.0
This user guide will help you get started with ESP32-S3-DevKitC-1 and will also provide more in-depth information.
The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, ESP32-S3-
WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® Low Energy MCU module that
integrates complete Wi-Fi and Bluetooth Low Energy functions.
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing.
Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard.
The document consists of the following major sections:
    • Getting started: Overview of the board and hardware/software setup instructions to get started.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: Revision history, known issues, and links to user guides for previous versions (if
      any) of the board.
    • Related Documents: Links to related documentation.


1.1.1    Getting Started

This section provides a brief introduction of ESP32-S3-DevKitC-1, instructions on how to do the initial hardware
setup and how to flash firmware onto it.


Description of Components

The key components of the board are described in a counter-clockwise direction.




                                                                                                                    3


---

Chapter 1. ESP32-S3-DevKitC-1




                    Fig. 1: ESP32-S3-DevKitC-1 with ESP32-S3-WROOM-1 Module




                                Fig. 2: ESP32-S3-DevKitC-1 - front




Espressif Systems                           4                                 Release master
                                 Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




 Key Component                     Description
 ESP32-S3-WROOM-1/1U/2             ESP32-S3-WROOM-1, ESP32-S3-WROOM-1U, and ESP32-S3-WROOM-
                                   2 are powerful, generic Wi-Fi + Bluetooth Low Energy MCU modules that
                                   have a rich set of peripherals. They provide acceleration for neural net-
                                   work computing and signal processing workloads. ESP32-S3-WROOM-1 and
                                   ESP32-S3-WROOM-2 comes with a PCB antenna. ESP32-S3-WROOM-1U
                                   comes with an external antenna connector.
 5 V to 3.3 V LDO                  Power regulator that converts a 5 V supply into a 3.3 V output.
 Pin Headers                       All available GPIO pins (except for the SPI bus for flash) are broken out to the
                                   pin headers on the board for easy interfacing and programming. For details,
                                   please see Header Block.
 USB-to-UART Port                  A Micro-USB port used for power supply to the board, for flashing applications
                                   to the chip, as well as for communication with the chip via the on-board USB-
                                   to-UART bridge.
 Boot Button                       Download button. Holding down Boot and then pressing Reset initiates
                                   Firmware Download mode for downloading firmware through the serial port.
 Reset Button                      Press this button to restart the system.
 USB Port                          ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 speci-
                                   fication. The interface is used for power supply to the board, for flashing appli-
                                   cations to the chip, for communication with the chip using USB 1.1 protocols,
                                   as well as for JTAG debugging.
 USB-to-UART Bridge                Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
 RGB LED                           Addressable RGB LED, driven by GPIO38.
 3.3 V Power On LED                Turns on when the USB power is connected to the board.



Note: For boards with Octal SPI flash/PSRAM memory embedded ESP32-S3-WROOM-1/1U modules, and boards
with ESP32-S3-WROOM-2 modules, the pins GPIO35, GPIO36 and GPIO37 are used for the internal communi-
cation between ESP32-S3 and SPI flash/PSRAM memory, thus not available for external use.



Start Application Development

Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.


Required Hardware
    • ESP32-S3-DevKitC-1
    • USB 2.0 cable (Standard-A to Micro-B)
    • Computer running Windows, Linux, or macOS


Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed
data lines nor work for programming the boards.



Hardware Setup Connect the board with the computer using USB-to-UART Port or ESP32-S3 USB Port. In
subsequent steps, USB-to-UART Port will be used by default.


Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel-
opment environment and then flash an application example onto your board.




Espressif Systems                                 5                                                   Release master
                                       Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1


Contents and Packaging

Ordering Information The development board has a variety of variants to choose from, as shown in the table
below.


 Ordering Code                 Module Integrated              Flash               PSRAM          SPI Voltage
 ESP32-S3-DevKitC-1-           ESP32-S3-WROOM-1-              8 MB QD             8 MB OT        3.3 V
 N8R8                          N8R8
 ESP32-S3-DevKitC-1-           ESP32-S3-WROOM-2-              32 MB OT            16 MB OT       1.8 V
 N32R16V                       N32R16V
 ESP32-S3-DevKitC-1U-          ESP32-S3-WROOM-1U-             8 MB QD             8 MB OT        3.3 V
 N8R8                          N8R8



Note: In the table above, QD stands for Quad SPI and OT stands for Octal SPI.



Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or
any packaging depending on your retailer.
For retail orders, please go to https://www.espressif.com/en/contact-us/get-samples.


Wholesale Orders If you order in bulk, the boards come in large cardboard boxes.
For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.


1.1.2    Hardware Reference

Block Diagram

The block diagram below shows the components of ESP32-S3-DevKitC-1 and their interconnections.


Power Supply Options There are three mutually exclusive ways to provide power to the board:
    • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended)
    • 5V and G (GND) pins
    • 3V3 and G (GND) pins


Header Block

The two tables below provide the Name and Function of the pins on both sides of the board (J1 and J3). The pin
names are shown in ESP32-S3-DevKitC-1 - front. The numbering is the same as in the Board Schematic (PDF).




Espressif Systems                                  6                                            Release master
                                        Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




                               Fig. 3: ESP32-S3-DevKitC-1 (click to enlarge)


                                                    J1

 No.   Name     TypePage 8, 1 Function
 1     3V3      P            3.3 V power supply
 2     3V3      P            3.3 V power supply
 3     RST      I            EN
 4     4        I/O/T        RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3
 5     5        I/O/T        RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4
 6     6        I/O/T        RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5
 7     7        I/O/T        RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6
 8     15       I/O/T        RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P
 9     16       I/O/T        RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N
 10    17       I/O/T        RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6
 11    18       I/O/T        RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3
 12    8        I/O/T        RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1
 13    3        I/O/T        RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2
 14    46       I/O/T        GPIO46
 15    9        I/O/T        RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD
 16    10       I/O/T        RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4, SUB-
                             SPICS0
 17    11       I/O/T        RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5, SUBSPID
 18    12       I/O/T        RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6, SUB-
                             SPICLK
 19    13       I/O/T        RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7, SUBSPIQ
 20    14       I/O/T        RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS, SUB-
                             SPIWP
 21    5V       P            5 V power supply
 22    G        G            Ground



Espressif Systems                              7                                Release master
                                    Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1


    J3
            No.      Name        Type      Function
            1        G           G         Ground
            2        TX          I/O/T     U0TXD, GPIO43, CLK_OUT1
            3        RX          I/O/T     U0RXD, GPIO44, CLK_OUT2
            4        1           I/O/T     RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
            5        2           I/O/T     RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
            6        42          I/O/T     MTMS, GPIO42
            7        41          I/O/T     MTDI, GPIO41, CLK_OUT1
            8        40          I/O/T     MTDO, GPIO40, CLK_OUT2
            9        39          I/O/T     MTCK, GPIO39, CLK_OUT3, SUBSPICS1
            10       38          I/O/T     GPIO38, FSPIWP, SUBSPIWP, RGB LED
            11       37          I/O/T     SPIDQS, GPIO37, FSPIQ, SUBSPIQ
            12       36          I/O/T     SPIIO7, GPIO36, FSPICLK, SUBSPICLK
            13       35          I/O/T     SPIIO6, GPIO35, FSPID, SUBSPID
            14       0           I/O/T     RTC_GPIO0, GPIO0
            15       45          I/O/T     GPIO45
            16       48          I/O/T     GPIO48, SPICLK_N, SUBSPICLK_N_DIFF
            17       47          I/O/T     GPIO47, SPICLK_P, SUBSPICLK_P_DIFF
            18       21          I/O/T     RTC_GPIO21, GPIO21
            19       20          I/O/T     RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
            20       19          I/O/T     RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
            21       G           G         Ground
            22       G           G         Ground


For description of function names, please refer to ESP32-S3 Series Datasheet (PDF).




                                 Fig. 4: ESP32-S3-DevKitC-1 Pin Layout (click to enlarge)

Pin Layout
  1 P: Power supply; I: Input; O: Output; T: High impedance.




Espressif Systems                                          8                                Release master
                                                Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1


1.1.3     Hardware Revision Details

Initial release


Note: Both the initial and v1.1 versions of ESP32-S3-DevKitC-1 are available on the market. The main difference
lies in the GPIO assignment for the RGB LED: the initial version uses GPIO48, whereas v1.1 uses GPIO38.



1.1.4     Related Documents

    • ESP32-S3 Datasheet (PDF)
    • ESP32-S3-WROOM-1 & ESP32-S3-WROOM-1U Datasheet (PDF)
    • ESP32-S3-WROOM-2 Datasheet (PDF)
    • ESP32-S3-DevKitC-1 Schematic (PDF)
    • ESP32-S3-DevKitC-1 PCB layout (PDF)
    • ESP32-S3-DevKitC-1 Dimensions (PDF)
    • ESP32-S3-DevKitC-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online
    • ESP32-S3-DevKitC-1 Reference Design (ZIP)
For further design documentation for the board, please contact us at sales@espressif.com.


ESP32-S3-DevKitC-1 v1.0



The latest version: ESP32-S3-DevKitC-1 v1.1
This user guide will help you get started with ESP32-S3-DevKitC-1 and will also provide more in-depth information.
The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, ESP32-S3-
WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® Low Energy MCU module that
integrates complete Wi-Fi and Bluetooth Low Energy functions.
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing.
Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard.
The document consists of the following major sections:
    • Getting started: Overview of the board and hardware/software setup instructions to get started.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: Revision history, known issues, and links to user guides for previous versions (if
      any) of the board.
    • Related Documents: Links to related documentation.


Getting Started This section provides a brief introduction of ESP32-S3-DevKitC-1, instructions on how to do the
initial hardware setup and how to flash firmware onto it.


Description of Components The key components of the board are described in a counter-clockwise direction.




Espressif Systems                                   9                                                 Release master
                                         Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




                    Fig. 5: ESP32-S3-DevKitC-1 with ESP32-S3-WROOM-1 Module




                                Fig. 6: ESP32-S3-DevKitC-1 - front




Espressif Systems                           10                                Release master
                                 Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




 Key Component                     Description
 ESP32-S3-WROOM-1/1U/2             ESP32-S3-WROOM-1, ESP32-S3-WROOM-1U, and ESP32-S3-WROOM-
                                   2 are powerful, generic Wi-Fi + Bluetooth Low Energy MCU modules that
                                   have a rich set of peripherals. They provide acceleration for neural net-
                                   work computing and signal processing workloads. ESP32-S3-WROOM-1 and
                                   ESP32-S3-WROOM-2 comes with a PCB antenna. ESP32-S3-WROOM-1U
                                   comes with an external antenna connector.
 5 V to 3.3 V LDO                  Power regulator that converts a 5 V supply into a 3.3 V output.
 Pin Headers                       All available GPIO pins (except for the SPI bus for flash) are broken out to the
                                   pin headers on the board for easy interfacing and programming. For details,
                                   please see Header Block.
 USB-to-UART Port                  A Micro-USB port used for power supply to the board, for flashing applications
                                   to the chip, as well as for communication with the chip via the on-board USB-
                                   to-UART bridge.
 Boot Button                       Download button. Holding down Boot and then pressing Reset initiates
                                   Firmware Download mode for downloading firmware through the serial port.
 Reset Button                      Press this button to restart the system.
 ESP32-S3 USB Port                 ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 speci-
                                   fication. The interface is used for power supply to the board, for flashing appli-
                                   cations to the chip, for communication with the chip using USB 1.1 protocols,
                                   as well as for JTAG debugging.
 USB-to-UART Bridge                Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
 RGB LED                           Addressable RGB LED, driven by GPIO48.
 3.3 V Power On LED                Turns on when the USB power is connected to the board.



Note: For boards with Octal SPI flash/PSRAM memory embedded ESP32-S3-WROOM-1/1U modules, and boards
with ESP32-S3-WROOM-2 modules, the pins GPIO35, GPIO36 and GPIO37 are used for the internal communi-
cation between ESP32-S3 and SPI flash/PSRAM memory, thus not available for external use.



Start Application Development Before powering up your board, please make sure that it is in good condition with
no obvious signs of damage.


Required Hardware
   • ESP32-S3-DevKitC-1
   • USB 2.0 cable (Standard-A to Micro-B)
   • Computer running Windows, Linux, or macOS


Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed
data lines nor work for programming the boards.



Hardware Setup Connect the board with the computer using USB-to-UART Port. Connection using ESP32-S3
USB Port is not fully implemented in software. In subsequent steps, USB-to-UART Port will be used by default.


Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel-
opment environment and then flash an application example onto your board.


Contents and Packaging




Espressif Systems                                 11                                                  Release master
                                       Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1


Ordering Information The development board has a variety of variants to choose from, as shown in the table
below.


 Ordering Code                 Module Integrated             Flash               PSRAM           SPI Voltage
 ESP32-S3-DevKitC-1-           ESP32-S3-WROOM-1-             8 MB QD             8 MB OT         3.3 V
 N8R8                          N8R8
 ESP32-S3-DevKitC-1-           ESP32-S3-WROOM-2-             32 MB OT            16 MB OT        1.8 V
 N32R16V                       N32R16V
 ESP32-S3-DevKitC-1U-          ESP32-S3-WROOM-1U-            8 MB QD             8 MB OT         3.3 V
 N8R8                          N8R8



Note: In the table above, QD stands for Quad SPI and OT stands for Octal SPI.



Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or
any packaging depending on your retailer.
For retail orders, please go to https://www.espressif.com/en/company/contact/buy-a-sample.


Wholesale Orders If you order in bulk, the boards come in large cardboard boxes.
For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.


Hardware Reference


Block Diagram The block diagram below shows the components of ESP32-S3-DevKitC-1 and their interconnec-
tions.


Power Supply Options There are three mutually exclusive ways to provide power to the board:
    • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended)
    • 5V and G (GND) pins
    • 3V3 and G (GND) pins


Header Block The two tables below provide the Name and Function of the pins on both sides of the board (J1 and
J3). The pin names are shown in ESP32-S3-DevKitC-1 - front. The numbering is the same as in the Board Schematic
(PDF).




Espressif Systems                                 12                                            Release master
                                       Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




                               Fig. 7: ESP32-S3-DevKitC-1 (click to enlarge)


                                                    J1

 No.   Name     TypePage 14, 1 Function
 1     3V3      P             3.3 V power supply
 2     3V3      P             3.3 V power supply
 3     RST      I             EN
 4     4        I/O/T         RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3
 5     5        I/O/T         RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4
 6     6        I/O/T         RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5
 7     7        I/O/T         RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6
 8     15       I/O/T         RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P
 9     16       I/O/T         RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N
 10    17       I/O/T         RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6
 11    18       I/O/T         RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3
 12    8        I/O/T         RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1
 13    3        I/O/T         RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2
 14    46       I/O/T         GPIO46
 15    9        I/O/T         RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD
 16    10       I/O/T         RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4, SUB-
                              SPICS0
 17    11       I/O/T         RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5, SUBSPID
 18    12       I/O/T         RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6, SUB-
                              SPICLK
 19    13       I/O/T         RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7, SUBSPIQ
 20    14       I/O/T         RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS, SUB-
                              SPIWP
 21    5V       P             5 V power supply
 22    G        G             Ground



Espressif Systems                               13                               Release master
                                     Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1


    J3
            No.      Name        Type      Function
            1        G           G         Ground
            2        TX          I/O/T     U0TXD, GPIO43, CLK_OUT1
            3        RX          I/O/T     U0RXD, GPIO44, CLK_OUT2
            4        1           I/O/T     RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
            5        2           I/O/T     RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
            6        42          I/O/T     MTMS, GPIO42
            7        41          I/O/T     MTDI, GPIO41, CLK_OUT1
            8        40          I/O/T     MTDO, GPIO40, CLK_OUT2
            9        39          I/O/T     MTCK, GPIO39, CLK_OUT3, SUBSPICS1
            10       38          I/O/T     GPIO38, FSPIWP, SUBSPIWP
            11       37          I/O/T     SPIDQS, GPIO37, FSPIQ, SUBSPIQ
            12       36          I/O/T     SPIIO7, GPIO36, FSPICLK, SUBSPICLK
            13       35          I/O/T     SPIIO6, GPIO35, FSPID, SUBSPID
            14       0           I/O/T     RTC_GPIO0, GPIO0
            15       45          I/O/T     GPIO45
            16       48          I/O/T     GPIO48, SPICLK_N, SUBSPICLK_N_DIFF, RGB LED
            17       47          I/O/T     GPIO47, SPICLK_P, SUBSPICLK_P_DIFF
            18       21          I/O/T     RTC_GPIO21, GPIO21
            19       20          I/O/T     RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
            20       19          I/O/T     RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
            21       G           G         Ground
            22       G           G         Ground


For description of function names, please refer to Chip Datasheet (PDF).


Pin Layout


Hardware Revision Details This is the first revision of this board released.


Related Documents
    • ESP32-S3 Datasheet (PDF)
    • ESP32-S3-WROOM-1 & ESP32-S3-WROOM-1U Datasheet (PDF)
    • ESP32-S3-WROOM-2 Datasheet (PDF)
    • ESP32-S3-DevKitC-1 Schematic (PDF)
    • ESP32-S3-DevKitC-1 PCB layout (PDF)
    • ESP32-S3-DevKitC-1 Dimensions (PDF)
    • ESP32-S3-DevKitC-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online
For further design documentation for the board, please contact us at sales@espressif.com.




  1 P: Power supply; I: Input; O: Output; T: High impedance.




Espressif Systems                                          14                                Release master
                                                Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




                       Fig. 8: ESP32-S3-DevKitC-1 Pin Layout (click to enlarge)




Espressif Systems                            15                                   Release master
                                  Submit Document Feedback


---

Chapter 1. ESP32-S3-DevKitC-1




Espressif Systems                          16              Release master
                                Submit Document Feedback


---

Chapter 2

ESP32-S3-USB-OTG


ESP32-S3-USB-OTG is a development board that focuses on USB-OTG function verification and application devel-
opment.
Application examples for this board can be found at Examples .


2.1     ESP32-S3-USB-OTG


ESP32-S3-USB-OTG is a development board that focuses on USB-OTG function verification and application devel-
opment. It is based on ESP32-S3 SoC, supports Wi-Fi and BLE 5.0 wireless functions, and supports USB host and
USB device functions. It can be used to develop applications such as wireless storage devices, Wi-Fi network cards,
LTE MiFi, multimedia devices, virtual keyboards and mice. The development board has the following features:
    • Onboard ESP32-S3-MINI-1-N8 module, with built-in 8 MB flash
    • Onboard USB Type-A host and device interface, with built-in USB interface switching circuit
    • Onboard USB to serial debugging chip (Micro USB interface)
    • Onboard 1.3-inch LCD color screen, supports GUI
    • Onboard SD card interface, compatible with SDIO and SPI interfaces
    • Onboard charging IC, can be connected to lithium battery
The document consists of the following major sections:
    • Getting Started: Provides a brief overview of ESP32-S3-USB-OTG and necessary hardware and software in-
      formation.
    • Hardware Reference: Provides detailed hardware information of ESP32-S3-USB-OTG.
    • Related Documents: Provides links to related documents.


2.1.1    Getting Started

This section describes how to start using ESP32-S3-USB-OTG. It includes introduction to basic information about
ESP32-S3-USB-OTG first, and then on how to start using the development board for application development, as
well as board packaging and retail information.


Description of Components

The ESP32-S3-USB-OTG development board includes the following parts:
    • Motherboard: ESP32-S3-USB-OTG motherboard is the core of the kit. The motherboard integrates the
      ESP32-S3-MINI-1 module and provides an interface of the 1.3-inch LCD screen.


                                                                                                                17


---

Chapter 2. ESP32-S3-USB-OTG




                              Fig. 1: ESP32-S3-USB-OTG (click to enlarge)




Espressif Systems                             18                            Release master
                                   Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG




                      Fig. 2: ESP32-S3-USB-OTG Top View (click to enlarge)




Espressif Systems                          19                                Release master
                                Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


The following table starts with the USB_HOST Interface on the left, and introduces the main components in the
above figure in an anticlockwise order.


 Main components                    Description
 USB_HOST Interface                 USB Type-A female port, used to connect other USB devices.
 ESP32-S3-MINI-1 Module             ESP32-S3-MINI-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module
                                    that has a rich set of peripherals. It has strong ability for neural network com-
                                    puting and signal processing. ESP32-S3-MINI-1 comes with a PCB antenna
                                    and is pin-to-pin compatible with ESP32-S2-MINI-1.
 MENU Button                        Menu button.
 Micro SD Card Slot                 Micro SD card can be inserted. Both four-line SDIO and SPI mode are sup-
                                    ported.
 USB Switch IC                      By setting the level of USB_SEL, you can switch USB peripherals to make
                                    them either connected to the USB_DEV interface or the USB_HOST interface.
                                    USB_DEV will be connected by default.
 Reset Button                       Press this button to restart the system.
 USB_DEV Interface                  USB Type-A male port, can be connected to the USB host, and also used as a
                                    lithium battery charge power source.
 Power Switch                       Switch to ON to use battery power. Switch to OFF to power off battery.
 Boot Button                        Download button. Holding down Boot and then pressing Reset initiates
                                    Firmware Download mode for downloading firmware through the serial port.
 DW- Button                         Down button.
 LCD FPC Connector                  Used to connect the 1.3-inch LCD screen.
 UP+ Button                         Up button.
 USB-to-UART Interface              A Micro-USB port used for power supply to the board, for flashing applications
                                    to the chip, as well as for communication with the chip via the on-board USB-
                                    to-UART bridge.


The following table starts with the Yellow LED on the left, and introduces the main components in the above figure
in an anticlockwise order.


 Main components                    Description
 Yellow LED                         Driven by GPIO16, set high level to turn on.
 Green LED                          Driven by GPIO15, set high level to turn on.
 Charging LED                       During charging, the red light is on, which will be turned off when charged.
 Battery Solder Joints              3.6 V lithium battery can be welded to power the motherboard.
 Charging Circuit                   Used to charge lithium battery.
 Free Pins                          Idle pins that can be customized.
 USB-to-UART Bridge                 Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.

    • Subboard: ESP32-S3-USB-OTG-SUB mount the 1.3-inch LCD screen


Application Examples

The following application examples are available for ESP32-S3-USB-OTG:
    • factory - Demonstrates a factory demo for the ESP32-S3-USB-OTG development board, providing a reference
      for building, flashing, and monitoring projects using ESP-IDF and ESP Launchpad.
For more examples and the latest updates, please refer to the examples folder.
To explore the application examples or to develop your own, please follow the steps outlined in the Start Application
Development section.




Espressif Systems                                  20                                                 Release master
                                        Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG




                     Fig. 3: ESP32-S3-USB-OTG Bottom View (click to enlarge)




                       Fig. 4: ESP32-S3-USB-OTG Subboard (click to enlarge)




Espressif Systems                           21                                 Release master
                                 Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


Start Application Development

Before powering on the ESP32-S3-USB-OTG, please make sure that the development board is intact.


Required Hardware
    • ESP32-S3-USB-OTG
    • A USB 2.0 data cable (standard A to Micro-B)
    • Computer (Windows, Linux or macOS)


Software Setup Please proceed to Get Started, where Section Installation Step by Step will quickly help you set
up the development environment and then flash an application example onto your board.


Contents and Packaging

Retail Orders If you order a few samples, each board comes in an individual package in either an antistatic bag or
any packaging depending on your retailer.




                             Fig. 5: ESP32-S3-USB-OTG Package (click to enlarge)

Which contains the following parts:
    • Motherboard:
         – ESP32-S3-USB-OTG
    • Subboard:
         – ESP32-S3-USB-OTG_SUB
    • Fastener
         – Mounting bolt (x4)
         – Screw (x4)


Espressif Systems                                 22                                               Release master
                                       Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


         – Nut (x4)
For retail orders, please go to https://www.espressif.com/zh-hans/company/contact/buy-a-sample.


Wholesale Order If purchased in bulk, the development board will be packaged in a large cardboard box.
For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.


2.1.2    Hardware Reference

Block Diagram

The block diagram below shows the components of ESP32-S3-USB-OTG and their interconnections.




                         Fig. 6: ESP32-S3-USB-OTG Block Diagram (click to enlarge)

Please note that the external interface corresponding to the USB_HOST D+ D- signal in the functional block diagram
is USB DEV, which means that ESP32-S3 is used as a device to receive signals from other USB hosts. The external
interface corresponding to the USB_DEV D+ D- signal is USB HOST, which means that ESP32-S3 acts as a host
to control other devices.


Power Supply Options

There are three power supply methods for the development board:
   1. Power supply through the Micro_USB interface
        • Use the USB cable (standard A to Micro-B) to connect the motherboard to a power supply device, and
          set battery switch to OFF. Please note that in this power supply mode, only the motherboard and display
          are powered.
   2. Power supply through the USB_DEV interface



Espressif Systems                                 23                                               Release master
                                       Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


        • Set DEV_VBUS_EN to high level, and set the battery switch to OFF. This mode can supply power to the
          USB HOST interface. The lithium battery will be charged at the same time (if the lithium battery is
          installed)
   3. Power supply through the battery
        • Set BOOST_EN to high level, and set the battery switch to ON. You should solder a 1-Serial lithium
          battery (3.7 V ~ 4.2 V) to the power solder joint reserved on the back of the motherboard first. This
          mode can supply power to the USB HOST interface at the same time. The battery interface description
          is as follows:




                                  Fig. 7: Battery Connection (click to enlarge)



USB HOST Interface Power Options

The USB HOST interface (Type-A female port) can supply power to the connected USB device. The power supply
voltage is 5 V and the maximum current is 500 mA.
   • There are two power supply methods for the USB HOST interface:
       1. Power is supplied through the USB_DEV interface, and the 5 V power is directly from the power source
          connected to the interface.
       2. Power is supplied through the lithium battery, and the 3.6 V ~ 4.2 V voltage of the lithium battery
          is boosted to 5 V through the Boost circuit. The working status of Boost IC can be controlled by
          BOOST_EN/GPIO13, set high to enable Boost.
   • USB HOST interface power supply selection:




Espressif Systems                                24                                             Release master
                                      Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG




                                      Fig. 8: Boost Circuit (click to enlarge)



 BOOST_EN                         DEV_VBUS_EN                                Power Source
 0                                1                                          USB_DEV
 1                                0                                          Battery
 0                                0                                          No output
 1                                1                                          Undefined




                                 Fig. 9: Power Switch Circuit (click to enlarge)

     • 500 mA current limiting circuit:
         1. The current limiting IC MIC2005A can limit the maximum output current of the USB HOST interface
            to 500 mA. Please set the IDEV_LIMIT_EN (GPIO17) to high level to enable the current-limiting IC
            to output voltage.




Espressif Systems                                 25                                          Release master
                                       Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG




                      Fig. 10: 500 mA Current Limiting Circuit (click to enlarge)




                        Fig. 11: USB Interface Switch Circuit (click to enlarge)




Espressif Systems                            26                                     Release master
                                  Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


USB Interface Switch Circuit

    • When USB_SEL (GPIO18) is set to high level, the USB D+/D- Pin (GPIO19, 20) will be connected to
      USB_DEV D+ D-. Then you can use the USB HOST interface (Type-A female Port) to connect other USB
      devices.
    • When USB_SEL (GPIO18) is set to low level, the USB D+/D- Pin (GPIO19, 20) will be connected to
      USB_HOST D+ D-. Then you can use the USB DEV interface (Type-A male port) to connect to a host like
      a PC.
    • USB_SEL is pulled low level by default.


LCD Interface




                                  Fig. 12: LCD Interface Circuit (click to enlarge)

Please note that this interface supports connecting SPI interface screens. The screen controller used by this develop-
ment board is ST7789, and LCD_BL (GPIO9) can be used to control the screen backlight.


SD Card Interface

Please note that the SD card interface is compatible with 1-wire, 4-wire SDIO mode and SPI mode. After being
powered on, the card will be in 3.3 V signaling mode. Please send the first CMD0 command to select the bus mode:
SD mode or SPI mode.


Charging Circuit

Please note that the Type-A male port can be connected to a power adapter that outputs 5 V. When charging the
battery, the red indicator LED is on, after fully charged, the red indicator LED is off. When using the charging
circuit, please set the battery switch to OFF. The charging current is 212.7 mA.



Espressif Systems                                   27                                                Release master
                                         Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG




                         Fig. 13: SD Card Interface Circuit (click to enlarge)




                              Fig. 14: Charging Circuit (click to enlarge)




Espressif Systems                            28                                  Release master
                                  Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


Pin Layout

Function pin:


 No.         ESP32-S3-MINI-      Description
             1 Pin
 1           GPIO18              USB_SEL: Used to switch the USB interface. When high level, the
                                 USB_HOST interface is enabled. When low level (default), the USB_DEV
                                 interface is enabled.
 2           GPIO19              Connect with USB D-.
 3           GPIO20              Connect with USB D+.
 4           GPIO15              LED_GREEN: the light is lit when set high level.
 5           GPIO16              LED_YELLOW: the light is lit when set high level.
 6           GPIO0               BUTTON_OK: OK button, low level when pressed.
 7           GPIO11              BUTTON_DW: Down button, low level when pressed.
 8           GPIO10              BUTTON_UP: UP button, low level when pressed.
 9           GPIO14              BUTTON_MENU: Menu button, low level when pressed.
 10          GPIO8               LCD_RET: used to reset LCD, low level to reset.
 11          GPIO5               LCD_EN: used to enable LCD, low level to enable.
 12          GPIO4               LCD_DC: Used to switch data and command status.
 13          GPIO6               LCD_SCLK: LCD SPI Clock.
 14          GPIO7               LCD_SDA: LCD SPI MOSI.
 15          GPIO9               LCD_BL: LCD backlight control.
 16          GPIO36              SD_SCK: SD SPI CLK / SDIO CLK.
 17          GPIO37              SD_DO: SD SPI MISO / SDIO Data0.
 18          GPIO38              SD_D1: SDIO Data1.
 19          GPIO33              SD_D2: SDIO Data2.
 20          GPIO34              SD_D3: SD SPI CS / SDIO Data3.
 21          GPIO1               HOST_VOL: USB_DEV voltage monitoring, ADC1 channel 0.
 22          GPIO2               BAT_VOL: Battery voltage monitoring, ADC1 channel 1.
 23          GPIO17              LIMIT_EN: Enable current limiting IC, high level enable.
 24          GPIO21              0VER_CURRENT: Current overrun signal, high level means overrun.
 25          GPIO12              DEV_VBUS_EN: High level to enable DEV_VBUS power supply.
 26          GPIO13              BOOST_EN: High level to enable Boost boost circuit.


Extended pin:


 No.         ESP32-S3-MINI-1 Pin            Description
 1           GPIO45                         FREE_1: Idle, can be customized.
 2           GPIO46                         FREE_2: Idle, can be customized.
 3           GPIO48                         FREE_3: Idle, can be customized.
 4           GPIO26                         FREE_4: Idle, can be customized.
 5           GPIO47                         FREE_5: Idle, can be customized.
 6           GPIO3                          FREE_6: Idle, can be customized.



2.1.3    Related Documents

Please download the following documents from the HTML version of esp-dev-kits Documentation.
     • ESP32-S3 Datasheet (PDF)
     • ESP32-S3-MINI-1/1U Datasheet (PDF)
     • Espressif Product Selection Tool
     • ESP32-S3-USB-OTG Schematic Diagram (PDF)
     • ESP32-S3-USB-OTG PCB Layout Drawing (PDF)
     • ESP32-S3-USB-OTG Reference Design (ZIP)


Espressif Systems                               29                                             Release master
                                     Submit Document Feedback


---

Chapter 2. ESP32-S3-USB-OTG


   • ST7789VW Datasheet (PDF)




Espressif Systems                          30              Release master
                                Submit Document Feedback


---

Chapter 3

ESP32-S3-LCD-EV-Board


ESP32-S3-LCD-EV-Board is a development board for evaluating and verifying esp32s3 screen interactive applica-
tions. It has the functions of touchscreen interaction and voice interaction.


Note: Please check the version number of your ESP32-S3-LCD-EV-Board-MB indicated by the silk marking on
the back. For boards of the v1.5 version, please refer to ESP32-S3-LCD-EV-Board v1.5. For boards of the v1.4 and
below versions, please refer to ESP32-S3-LCD-EV-Board v1.4.
Unless otherwise stated, the ESP32-S3-LCD-EV-Board in this document refers to both ESP32-S3-LCD-EV-Board
and ESP32-S3-LCD-EV-Board-2.




3.1     ESP32-S3-LCD-EV-Board v1.5



Note: Please check the version number of your ESP32-S3-LCD-EV-Board-MB indicated by the silk marking on
the back. For boards of the v1.5 version, please refer to this user guide. For boards of the v1.4 and below versions,
please refer to ESP32-S3-LCD-EV-Board v1.4.
Unless otherwise stated, the ESP32-S3-LCD-EV-Board in this document refers to both ESP32-S3-LCD-EV-Board
and ESP32-S3-LCD-EV-Board-2.


This user guide will help you get started with ESP32-S3-LCD-EV-Board and will also provide more in-depth infor-
mation.
The document consists of the following sections:
    • Board Overview: Overview of the board hardware/software.
    • Start Application Development: How to set up hardware/software to develop applications.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: This is the first revision of this board released.
    • Sample Request: How to get a sample board.
    • Related Documents: Links to related documentation.


3.1.1    Board Overview

ESP32-S3-LCD-EV-Board is an ESP32-S3-based development board with a touchscreen. Together with different
subboards, ESP32-S3-LCD-EV-Board can drive LCDs with IIC, SPI, 8080, and RGB interfaces. It houses dual array


                                                                                                                  31


---

Chapter 3. ESP32-S3-LCD-EV-Board


microphones, supports voice recognition and near/far-field voice wake-up, and features screen and voice interaction.
The board caters to development needs for touchscreen products with different resolutions and interfaces.
Currently, we have two boards available:
    • ESP32-S3-LCD-EV-Board with 480x480 LCD
    • ESP32-S3-LCD-EV-Board-2 with 800x480 LCD




                              Fig. 1: ESP32-S3-LCD-EV-Board with 480x480 LCD



Feature List

The main features of the board are listed below:
    • Module Embedded: ESP32-S3-WROOM-1 module with 16 MB flash and 16 MB PSRAM
    • Display: Compatibility with various subboards and support for displays with RGB, 8080, SPI, and I2C
      interfaces. Please refer to LCD Subboards for more information
    • Audio: Audio Codec + ADC amplifier and dual microphones
    • USB: USB to serial port chip plus USB Type-C download/debug


Block Diagram

The block diagram below shows the components of ESP32-S3-LCD-EV-Board and their interconnections.


Espressif Systems                                  32                                               Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                         Fig. 2: ESP32-S3-LCD-EV-Board-2 with 800x480 LCD




                    Fig. 3: ESP32-S3-LCD-EV-Board Block Diagram (Click to Enlarge)


Espressif Systems                             33                                     Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


Description of Components

The ESP32-S3-LCD-EV-Board consists of a mainboard and a subboard (see LCD Subboards for options). Addition-
ally, it allows for a selection of a USB Type-A adapter.


Mainboard ESP32-S3-LCD-EV-Board-MB is the core of the kit, which integrates the ESP32-S3-WROOM-1
module and provides ports for connection to the LCD subboard.




                        Fig. 4: ESP32-S3-LCD-EV-Board-MB - Front (Click to Enlarge)

The key components of the board are described in a counter-clockwise direction.




Espressif Systems                                 34                                         Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




 Key Component                   Description
 ESP32-S3-WROOM-1-               ESP32-S3-WROOM-1-N16R16V is a generic Wi-Fi + Bluetooth LE MCU
 N16R16V Module                  module that is built around the ESP32-S3 series of SoCs. It is integrated with
                                 16 MB flash and 16 MB PSRAM. On top of a rich set of peripherals, the accel-
                                 eration for neural network computing and signal processing workloads provided
                                 by the SoC makes the module an ideal choice for a wide variety of application
                                 scenarios related to Artificial Intelligence of Things (AIoT).
 Reset Button                    Press this button to reset the system.
 Boot Button                     Holding down the Boot key and momentarily pressing the Reset key initiates
                                 the firmware upload mode. Then you can upload firmware through the serial
                                 port or USB.
 Expansion Connector             Provides connections for all I/O expander pins, all power supply pins, and some
                                 module pins.
 I/O Expander                    TCA9554 is a device that provides 8 bits of general purpose parallel I/O ex-
                                 pansion. It controls the I/O mode and level via two-line bidirectional I2C bus,
                                 offering a simple solution when additional I/Os are needed.
 LCD Board Connector             Three different types of LCD subboards can be connected via connectors with
                                 2.54 mm pitch.
 LED                             Supports configuring the RGB LED display to indicate status or behavior.
 USB-to-USB Port                 Provides power to the entire system (choose either USB-to-USB or USB-to-
                                 UART port). It is recommended to use at least a 5V/2A power adapter to
                                 ensure stable power supply. Used for USB communication between the PC
                                 and the ESP32-S3-WROOM-1 module.
 USB-to-UART Port                Provides power to the entire system (choose either USB-to-USB or USB-to-
                                 UART port). It is recommended to use at least a 5V/2A power adapter to
                                 ensure stable power supply. Used for serial communication between the PC
                                 side and the ESP32-S3-WROOM-1 module.
 Left Microphone                 On-board microphone, connected to Audio ADC Chip.
 Right Microphone                On-board microphone, connected to Audio ADC Chip.
 Audio ADC Chip                  ES7210 is a high performance, low power 4-channel audio ADC for applica-
                                 tions of microphone arrays. Featuring Acoustic Echo Cancellation (AEC), it
                                 is an ideal choice for music and voice applications.
 USB-to-UART Bridge Con-         CP2102N, the single-chip USB-to-UART bridge controller, provides up to 3
 troller                         Mbps connection for software download and debugging.
 Audio Codec Chip                ES8311 is a low-power mono audio codec that includes a single-channel ADC
                                 and DAC, low noise pre-amplifier, headphone driver, digital audio, analog mix-
                                 ing, and gain function. It connects to the ESP32-S3-WROOM-1 module via
                                 I2S and I2C buses to process audio through hardware instead of the audio ap-
                                 plication.
 Audio Amplifier                 NS4150 is a low EMI, 3 W mono class D audio amplifier used to drive speakers
                                 by amplifying the audio signal from the audio codec chip.
 Speaker Connector               External speaker playback is possible with the help of the audio amplifier.


LCD Subboards The mainboard can be used together with three different kinds of subboards:




Espressif Systems                               35                                                Release master
                                     Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




 Board Name                      Dis-        Reso-        LCD Driver    Touch       Available       Development
                                 play        lution       (Interface)   Driver      Boards
                                 (Inch)      (Px)
 ESP32-S3-LCD-EV-Board-          0.96        128      x   SSD1315       N/A         Not Available
 SUB1 v1.0                                   64           (I2C)
                                 2.40        320      x   ST7789V       XTP2046 Not Available
                                             240          (SPI)
 ESP32-S3-LCD-EV-Board-          3.50        480      x   ST7796S       GT911       Not Available
 SUB2 v1.5                                   320          (8080)
                                 3.95        480      x   GC9503CV      FT5x06      ESP32-S3-LCD-EV-Board
                                             480          (RGB)
 ESP32-S3-LCD-EV-Board-          4.30        800      x   ST7262E43     GT1151 ESP32-S3-LCD-EV-Board-2
 SUB3 v1.3                                   480          (RGB)

   • ESP32-S3-LCD-EV-Board-SUB1 subboard has two interfaces, which support connection to a 2.4-inch dis-
     play with the SPI interface or a 0.96-inch display with the I2C interface. This board is not yet configured, so
     it is not further explained here.
   • ESP32-S3-LCD-EV-Board-SUB2 subboard has two interfaces, which support connection to a display with
     the RGB interface or a display with the 8080 parallel interface. The current subboard has a 3.95-inch touch-
     screen with the RGB565 interface and 480x480 resolution. The LCD driver IC is GC9503CV and the touch-
     screen driver IC is FT5x06.




                      Fig. 5: ESP32-S3-LCD-EV-Board-SUB2 - Front (Click to Enlarge)

   • ESP32-S3-LCD-EV-Board-SUB3 subboard only supports a 4.3-inch touchscreen with the RGB565 interface


Espressif Systems                                  36                                               Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                       Fig. 6: ESP32-S3-LCD-EV-Board-SUB2 - Back (Click to Enlarge)


      and 800x480 resolution. The LCD driver IC is ST7262E43 and the touchscreen driver IC is GT1151.


USB Type-A Adapter With the USB Type-A adapter, the mainboard can serve as a USB host for connection to
USB devices.


Application Examples

The following application examples are available for ESP32-S3-LCD-EV-Board v1.5:
   • 86-box Demo Example - Demonstrates a GUI demo designed for a control panel (480x480) typically used for
     wall-mounted 86 type box, providing a smooth graphic operation experience with features like weather report,
     hot water heater, warm air heater page, and audio output function.
   • 86-box Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice
     recognition function, providing a reference for flashing the board and troubleshooting potential issues.
   • LVGL Demos Example - Demonstrates how to run LVGL s demos on an ESP32-S3-LCD-EV-Board, show-
     casing three methods to avoid tearing effect using different buffering modes, and providing performance testing
     results for different buffering modes.
   • Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice recognition
     function, providing instructions on how to flash the example to the ESP32-S3-LCD-EV-Board and configure
     it for use.
   • USB Camera LCD Example - Demonstrates how to use an LCD display to show video captured from a USB
     camera, with options to transfer frames to Wi-Fi and log memory information, providing a basis for developing
     applications with ESP32-S3-LCD-EV-Board.
   • USB File System - Demonstrates how to use USB HOST on ESP32-S2/ESP32-S3 to read and write files on
     a USB flash drive, displaying its contents on the screen, with support for various file formats for preview.
   • USB Keyboard Example - Demonstrates how to use LCD and LVGL to simulate a USB keyboard on the
     ESP32-S3-LCD-EV-Board, providing a GUI of a USB keyboard that can interact with a PC like a real key-


Espressif Systems                                 37                                                Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 7: ESP32-S3-LCD-EV-Board-SUB3 - Front (Click to Enlarge)




Espressif Systems                             38                                    Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 8: ESP32-S3-LCD-EV-Board-SUB3 - Back (Click to Enlarge)




                       Fig. 9: USB Type-A Adapter v1.1 - Front (Click to Enlarge)



Espressif Systems                             39                                    Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




              Fig. 10: USB Type-A Adapter v1.1 - Connected to the Mainboard (Click to Enlarge)




               Fig. 11: USB Type-A Adapter v1.1 - Connected to USB Devices (Click to Enlarge)




Espressif Systems                               40                                               Release master
                                     Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


        board.
For more examples and the latest updates, please refer to the examples folder.
To explore the application examples or to develop your own, please follow the steps outlined in the Start Application
Development section.


3.1.2     Start Application Development

This section provides instructions on how to do hardware and software setup and flash firmware onto the board to
develop your own application.


Required Hardware

    • 1 x ESP32-S3-LCD-EV-Board-MB
    • 1 x LCD subboard
    • 1 x USB 2.0 cable (standard Type-A to Type-C)
    • 1 x PC (Windows, Linux, or macOS)


Note: Please make sure to use the appropriate USB cable. Some cables can only be used for charging, not for data
transfer or program flashing.



Optional Hardware
    • 1 x Speaker


Hardware Setup

Prepare the board for loading of the first sample application:
   1. Connect the LCD subboard to the LCD Board Connector.
   2. Plug in the USB cable to connect the PC with the board.
   3. The LCD lights up and you can start to interact with it.
Now the board is ready for software setup.


Software Setup

The development framework of ESP32-S3-LCD-EV-Board is ESP-IDF. ESP-IDF is a FreeRTOS-based SoC devel-
opment framework with a bunch of components including LCD, ADC, RMT, and SPI.
To learn how to quickly set up your development environment, please go to Get Started > Installation.


Note:
    • ESP-IDF v5.1.2 is required. It is recommended to use the latest release/v5.1 branch for development.
    • For more information about developing LCD applications, please refer to ESP-IoT-Solution Programming
      Guide.



3.1.3     Hardware Reference

This section provides more detailed information about the board s hardware.




Espressif Systems                                   41                                               Release master
                                         Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


GPIO Allocation

The table below provides the allocation of GPIOs exposed on terminals of ESP32-S3-WROOM-1 module to control
specific components or functions of the board.

                                Table 1: ESP32-S3-WROOM-1 GPIO Allocation
 Pin                      Pin Name                  Function
 1                        GND                       GND
 2                        3V3                       Power supply
 3                        EN                        RESET
 4                        IO4                       LED
 5                        IO5                       I2S_MCLK
 6                        IO6                       I2S_CODEC_DSDIN
 7                        IO7                       I2S_LRCK
 8                        IO15                      I2S_ADC_SDOUT
 9                        IO16                      I2S_SCLK
 10                       IO17                      LCD_DE
 11                       IO18                      LCD_DATA7
 12                       IO8                       LCD_DATA6
 13                       IO19                      USB_D-
 14                       IO20                      USB_D+
 15                       IO3                       LCD_VSYNC
 16                       IO46                      LCD_HSYNC
 17                       IO9                       LCD_PCLK
 18                       IO10                      LCD_DATA0
 19                       IO11                      LCD_DATA1
 20                       IO12                      LCD_DATA2
 21                       IO13                      LCD_DATA3
 22                       IO14                      LCD_DATA4
 23                       IO21                      LCD_DATA5
 24                       IO47                      I2C_SDA
 25                       IO48                      I2C_SCL
 26                       IO45                      LCD_DATA8
 27                       IO0                       BOOT
 28                       IO35                      No connection
 29                       IO36                      No connection
 30                       IO37                      No connection
 31                       IO38                      LCD_DATA9
 32                       IO39                      LCD_DATA10
 33                       IO40                      LCD_DATA11
 34                       IO41                      LCD_DATA12
 35                       IO42                      LCD_DATA13
 36                       RXD0                      UART_RXD0
 37                       TXD0                      UART_TXD0
 38                       IO2                       LCD_DATA14
 39                       IO1                       LCD_DATA15
 40                       GND                       GND
 41                       EPAD                      GND


The pins on the I/O expander connected to the module can be used for different functions.




Espressif Systems                                 42                                         Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board



                                    Table 2: I/O Expander GPIO Allocation
 IO Expander Pin                 Pin Name                         Function
 1                               A0                               GND
 2                               A1                               GND
 3                               A2                               GND
 4                               P0                               PA_CTRL
 5                               P1                               LCD_SPI_CS
 6                               P2                               LCD_SPI_SCK
 7                               P3                               LCD_SPI_MOSI
 8                               GND                              GND
 9                               P4                               Free
 10                              P5                               Free
 11                              P6                               Free
 12                              P7                               Free
 13                              INT                              No connection
 14                              SCL                              I2C_SCL
 15                              SDA                              I2C_SDA
 16                              VCC                              Supply voltage


Power Distribution

Power Supply over USB There are two ways to power the development board via USB power port.
   • Via USB-to-USB port




                        Fig. 12: ESP32-S3-LCD-EV-Board - USB-to-USB Power Supply

   • Via USB-to-UART port


Independent Audio and Digital Power Supply ESP32-S3-LCD-EV-Board features independent power supplies
for the audio components and ESP module. This should reduce noise in the audio signal from digital components and
improve the overall performance of the components.


AEC Path

The acoustic echo cancellation (AEC) path provides reference signals for AEC algorithm.



Espressif Systems                                 43                                              Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 13: ESP32-S3-LCD-EV-Board - USB-to-UART Power Supply




                       Fig. 14: ESP32-S3-LCD-EV-Board - Digital Power Supply




                       Fig. 15: ESP32-S3-LCD-EV-Board - Audio Power Supply


Espressif Systems                             44                                Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


ESP32-S3-LCD-EV-Board provides two compatible echo reference signal source designs. One is Codec (ES8311)
DAC output (DAC_AOUTLP/DAC_AOUTLP), the other is PA (NS4150) output (PA_OUT+/PA_OUT+). The
former is a default and the recommended selection. Resistors R54 and R56 shown in the figure below should not be
installed.
The echo reference signal is collected by ADC_MIC3P/ADC_MIC3N of ADC (ES7210) and then sent back to
ESP32-S3 for AEC algorithm.




               Fig. 16: ESP32-S3-LCD-EV-Board - AEC Codec DAC Output (Click to Enlarge)


Hardware Setup Options

Automatic Download There are two ways to put the development board into the download mode.
   • Press the Boot and Reset buttons. Release the Reset button first and then the Boot button.
   • The download is performed automatically by the software. The software uses the DTR and RTS signals from
     the serial port to control the status of the EN and IO0 pins.


3.1.4   Hardware Revision Details

ESP32-S3-LCD-EV-Board v1.5

   • The following pins are re-allocated for the ESP32-S3-WROOM-1-N16R16V module:
       – I2C_SCL: from IO18 to IO48
       – I2C_SDA: from IO8 to IO47
       – LCD_DATA6: from IO47 to IO8
       – LCD_DATA7: from IO48 to IO18
   • Level-shifting circuits are added to IO47 and IO48 for converting the 1.8 V logic level to a 3.3 V logic level.


ESP32-S3-LCD-EV-Board v1.4

   • Initial Release


3.1.5   Sample Request

This development board with the USB Type-A adapter is suitable for evaluating Espressif s high-performance HMI
Smart Displays Solution. For placing orders, please proceed to the Espressif Online Shop.


Espressif Systems                                 45                                                Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 17: SP32-S3-LCD-Ev-Board - AEC PA Output (Click to Enlarge)




           Fig. 18: ESP32-S3-LCD-EV-Board - AEC Reference Signal Collection (Click to Enlarge)




Espressif Systems                              46                                          Release master
                                    Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


3.1.6    Related Documents

Please download the following documents from the HTML version of esp-dev-kits Documentation.
    • ESP32-S3 Datasheet
    • ESP32-S3-WROOM-1 Datasheet
    • ESP Product Selector
    • ESP32-S3-LCD-EV-Board-MB Schematics
    • ESP32-S3-LCD-EV-Board-MB PCB Layout
    • ESP32-S3-LCD-EV-Board-SUB1 Schematics
    • ESP32-S3-LCD-EV-Board-SUB1 PCB Layout
    • ESP32-S3-LCD-EV-Board-SUB2 Schematics
    • ESP32-S3-LCD-EV-Board-SUB2 PCB Layout
    • 3.95_480x480_RGB_Display Specification
    • ESP32-S3-LCD-EV-Board-SUB3 Schematics
    • ESP32-S3-LCD-EV-Board-SUB3 PCB Layout
    • ESP32-S3-LCD-EV-Board USB Adapter Schematics
    • ESP32-S3-LCD-EV-Board USB Adapter PCB Layout
    • ESP32-S3-LCD-EV-Board Reference Design
    • TCA9554 Datasheet
    • 4.3_800x480_RGB_Display Specification
For further design documentation for the board, please contact us at sales@espressif.com.


ESP32-S3-LCD-EV-Board v1.4




Note: Please check the version number of your ESP32-S3-LCD-EV-Board-MB indicated by the silk marking on
the back. For boards of the v1.4 and below versions, please refer to this user guide. For boards of the v1.5 version,
please refer to ESP32-S3-LCD-EV-Board v1.5.
Unless otherwise stated, the ESP32-S3-LCD-EV-Board in this document refers to both ESP32-S3-LCD-EV-Board
and ESP32-S3-LCD-EV-Board-2.


This user guide will help you get started with ESP32-S3-LCD-EV-Board and will also provide more in-depth infor-
mation.
The document consists of the following sections:
    • Board Overview: Overview of the board hardware/software.
    • Start Application Development: How to set up hardware/software to develop applications.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: This is the first revision of this board released.
    • Sample Request: How to get a sample board.
    • Related Documents: Links to related documentation.


Board Overview ESP32-S3-LCD-EV-Board is an ESP32-S3-based development board with a touchscreen. To-
gether with different subboards, ESP32-S3-LCD-EV-Board can drive LCDs with IIC, SPI, 8080, and RGB inter-
faces. It houses dual array microphones, supports voice recognition and near/far-field voice wake-up, and features
screen and voice interaction. The board caters to development needs for touchscreen products with different resolu-
tions and interfaces.
Currently, we have two boards available:
    • ESP32-S3-LCD-EV-Board with 480x480 LCD
    • ESP32-S3-LCD-EV-Board-2 with 800x480 LCD




Espressif Systems                                  47                                                Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                       Fig. 19: ESP32-S3-LCD-EV-Board with 480x480 LCD




Espressif Systems                             48                         Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                       Fig. 20: ESP32-S3-LCD-EV-Board-2 with 800x480 LCD




Espressif Systems                             49                           Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


Feature List The main features of the board are listed below:
   • Module Embedded: ESP32-S3-WROOM-1 module with 16 MB flash and 8 MB PSRAM
   • Display: Compatibility with various subboards and support for displays with RGB, 8080, SPI, and I2C
     interfaces. Please refer to LCD Subboards for more information
   • Audio: Audio Codec + ADC amplifier and dual microphones
   • USB: USB to serial port chip plus USB Type-C download/debug


Block Diagram The block diagram below shows the components of ESP32-S3-LCD-EV-Board and their inter-
connections.




                     Fig. 21: ESP32-S3-LCD-EV-Board Block Diagram (Click to Enlarge)



Description of Components The ESP32-S3-LCD-EV-Board development board consists of a mainboard and a
subboard (see LCD Subboards for options). Additionally, it allows for a selection of a USB Type-A adapter.


Mainboard ESP32-S3-LCD-EV-Board-MB is the core of the kit, which integrates the ESP32-S3-WROOM-1
module and provides ports for connection to the LCD subboard.
The key components of the board are described in a counter-clockwise direction.




Espressif Systems                                 50                                        Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 22: ESP32-S3-LCD-EV-Board-MB - Front (Click to Enlarge)




Espressif Systems                             51                                   Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




 Key Component                   Description
 ESP32-S3-WROOM-1-               ESP32-S3-WROOM-1-N16R8 is a generic Wi-Fi + Bluetooth LE MCU mod-
 N16R8 Module                    ule that is built around the ESP32-S3 series of SoCs. It is integrated with 16
                                 MB flash and 8 MB PSRAM. On top of a rich set of peripherals, the acceler-
                                 ation for neural network computing and signal processing workloads provided
                                 by the SoC makes the module an ideal choice for a wide variety of application
                                 scenarios related to Artificial Intelligence of Things (AIoT).
 Reset Button                    Press this button to reset the system.
 Boot Button                     Holding down the Boot key and momentarily pressing the Reset key initiates
                                 the firmware upload mode. Then you can upload firmware through the serial
                                 port or USB.
 Expansion Connector             Provides connections for all I/O expander pins, all power supply pins, and some
                                 module pins.
 I/O Expander                    TCA9554 is a device that provides 8 bits of general purpose parallel I/O ex-
                                 pansion. It controls the I/O mode and level via two-line bidirectional I2C bus,
                                 offering a simple solution when additional I/Os are needed.
 LCD Board Connector             Three different types of LCD subboards can be connected via connectors with
                                 2.54 mm pitch.
 LED                             Supports configuring the RGB LED display to indicate status or behavior.
 USB-to-USB Port                 Provides power to the entire system (choose either USB-to-USB or USB-to-
                                 UART port). It is recommended to use at least a 5V/2A power adapter to
                                 ensure stable power supply. Used for USB communication between the PC
                                 and the ESP32-S3-WROOM-1 module.
 USB-to-UART Port                Provides power to the entire system (choose either USB-to-USB or USB-to-
                                 UART port). It is recommended to use at least a 5V/2A power adapter to
                                 ensure stable power supply. Used for serial communication between the PC
                                 side and the ESP32-S3-WROOM-1 module.
 Left Microphone                 On-board microphone, connected to Audio ADC Chip.
 Right Microphone                On-board microphone, connected to Audio ADC Chip.
 Audio ADC Chip                  ES7210 is a high performance, low power 4-channel audio ADC for applica-
                                 tions of microphone arrays. Featuring Acoustic Echo Cancellation (AEC), it
                                 is an ideal choice for music and voice applications.
 USB-to-UART Bridge Con-         CP2102N, the single-chip USB-to-UART bridge controller, provides up to 3
 troller                         Mbps connection for software download and debugging.
 Audio Codec Chip                ES8311 is a low-power mono audio codec that includes a single-channel ADC
                                 and DAC, low noise pre-amplifier, headphone driver, digital audio, analog mix-
                                 ing, and gain function. It connects to the ESP32-S3-WROOM-1 module via
                                 I2S and I2C buses to process audio through hardware instead of the audio ap-
                                 plication.
 Audio Amplifier                 NS4150 is a low EMI, 3 W mono class D audio amplifier used to drive speakers
                                 by amplifying the audio signal from the audio codec chip.
 Speaker Connector               External speaker playback is possible with the help of the audio amplifier.


LCD Subboards The mainboard can be used together with three different kinds of subboards:




Espressif Systems                               52                                                Release master
                                     Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




 Board Name                      Dis-        Reso-        LCD Driver    Touch       Available       Development
                                 play        lution       (Interface)   Driver      Boards
                                 (Inch)      (Px)
 ESP32-S3-LCD-EV-Board-          0.96        128      x   SSD1315       Not     Not Available
 SUB1 v1.0                                   64           (I2C)         Avail-
                                                                        able
                                 2.40        320      x   ST7789V       XTP2046 Not Available
                                             240          (SPI)
 ESP32-S3-LCD-EV-Board-          3.50        480      x   ST7796S       GT911       Not Available
 SUB2 v1.4                                   320          (8080)
                                 3.95        480      x   GC9503CV      FT5x06      ESP32-S3-LCD-EV-Board
                                             480          (RGB)
 ESP32-S3-LCD-EV-Board-          4.30        800      x   ST7262E43     GT1151 ESP32-S3-LCD-EV-Board-2
 SUB3 v1.3                                   480          (RGB)

   • The ESP32-S3-LCD-EV-Board-SUB1 subboard has two interfaces, which support connection to a 2.4-inch
     display with the SPI interface or a 0.96-inch display with the I2C interface. This board is not yet configured,
     so it is not further explained here.
   • The ESP32-S3-LCD-EV-Board-SUB2 subboard has two interfaces, which support connection to a display
     with the RGB interface or a display with the 8080 parallel interface. The current subboard has a 3.95-inch
     touchscreen with the RGB565 interface and 480x480 resolution. The LCD driver IC is GC9503CV and the
     touchscreen driver IC is FT5x06.




                      Fig. 23: ESP32-S3-LCD-EV-Board-SUB2 - Front (Click to Enlarge)



Espressif Systems                                  53                                               Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                      Fig. 24: ESP32-S3-LCD-EV-Board-SUB2 - Back (Click to Enlarge)


   • The ESP32-S3-LCD-EV-Board-SUB3 subboard only supports a 4.3-inch touchscreen with the RGB565
     interface and 800x480 resolution. The LCD driver IC is ST7262E43 and the touchscreen driver IC is GT1151.


USB Type-A Adapter With the USB Type-A adapter, the mainboard can serve as a USB host for connection to
USB devices.


Application Examples The following application examples are available for ESP32-S3-LCD-EV-Board v1.4:
   • 86-box Demo Example - Demonstrates a GUI demo designed for a control panel (480x480) typically used for
     wall-mounted 86 type box, providing a smooth graphic operation experience with features like weather report,
     hot water heater, warm air heater page, and audio output function.
   • 86-box Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice
     recognition function, providing a reference for flashing the board and troubleshooting potential issues.
   • LVGL Demos Example - Demonstrates how to run LVGL s demos on an ESP32-S3-LCD-EV-Board, show-
     casing three methods to avoid tearing effect using different buffering modes, and providing performance testing
     results for different buffering modes.
   • Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice recognition
     function, providing instructions on how to flash the example to the ESP32-S3-LCD-EV-Board and configure
     it for use.
   • USB Camera LCD Example - Demonstrates how to use an LCD display to show video captured from a USB
     camera, with options to transfer frames to Wi-Fi and log memory information, providing a basis for developing
     applications with ESP32-S3-LCD-EV-Board.
   • USB File System - Demonstrates how to use USB HOST on ESP32-S2/ESP32-S3 to read and write files on
     a USB flash drive, displaying its contents on the screen, with support for various file formats for preview.
   • USB Keyboard Example - Demonstrates how to use LCD and LVGL to simulate a USB keyboard on the
     ESP32-S3-LCD-EV-Board, providing a GUI of a USB keyboard that can interact with a PC like a real key-
     board.


Espressif Systems                                 54                                                Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 25: ESP32-S3-LCD-EV-Board-SUB3 - Front (Click to Enlarge)




                    Fig. 26: ESP32-S3-LCD-EV-Board-SUB3 - Back (Click to Enlarge)



Espressif Systems                             55                                     Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                        Fig. 27: USB Type-A Adapter v1.1 - Front (Click to Enlarge)




              Fig. 28: USB Type-A Adapter v1.1 - Connected to the Mainboard (Click to Enlarge)




Espressif Systems                               56                                               Release master
                                     Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                Fig. 29: USB Type-A Adapter v1.1 - Connected to USB Devices (Click to Enlarge)


For more examples and the latest updates, please refer to the examples folder.
To explore the application examples or to develop your own, please follow the steps outlined in the Start Application
Development section.


Start Application Development This section provides instructions on how to do hardware and software setup and
flash firmware onto the board to develop your own application.


Required Hardware
    • 1 x ESP32-S3-LCD-EV-Board-MB
    • 1 x LCD subboard
    • 1 x USB 2.0 cable (standard Type-A to Type-C)
    • 1 x PC (Windows, Linux, or macOS)


Note: Please make sure to use the appropriate USB cable. Some cables can only be used for charging, not for data
transfer or program flashing.



Optional Hardware
    • 1 x Speaker


Hardware Setup Prepare the board for loading of the first sample application:
   1. Connect the LCD subboard to the LCD Board Connector.
   2. Plug in the USB cable to connect the PC with the board.
   3. The LCD lights up and you can start to interact with it.
Now the board is ready for software setup.




Espressif Systems                                  57                                                Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


Software Setup The development framework of ESP32-S3-LCD-EV-Board is ESP-IDF. ESP-IDF is a
FreeRTOS-based SoC development framework with a bunch of components including LCD, ADC, RMT, and SPI.
To learn how to quickly set up your development environment, please go to Get Started > Installation.

Note:
    • ESP-IDF v5.1.2 is required. It is recommended to use the latest release/v5.1 branch for development.
    • For more information about developing LCD applications, please refer to ESP-IoT-Solution Programming
      Guide.



Hardware Reference This section provides more detailed information about the board s hardware.


GPIO Allocation The table below provides the allocation of GPIOs exposed on terminals of ESP32-S3-WROOM-
1 module to control specific components or functions of the board.

                                Table 3: ESP32-S3-WROOM-1 GPIO Allocation
 Pin                       Pin Name                 Function
 1                         GND                      GND
 2                         3V3                      Power supply
 3                         EN                       RESET
 4                         IO4                      LED
 5                         IO5                      I2S_MCLK
 6                         IO6                      I2S_CODEC_DSDIN
 7                         IO7                      I2S_LRCK
 8                         IO15                     I2S_ADC_SDOUT
 9                         IO16                     I2S_SCLK
 10                        IO17                     LCD_DE
 11                        IO18                     I2C_SCL
 12                        IO8                      I2C_SDA
 13                        IO19                     USB_D-
 14                        IO20                     USB_D+
 15                        IO3                      LCD_VSYNC
 16                        IO46                     LCD_HSYNC
 17                        IO9                      LCD_PCLK
 18                        IO10                     LCD_DATA0
 19                        IO11                     LCD_DATA1
 20                        IO12                     LCD_DATA2
 21                        IO13                     LCD_DATA3
 22                        IO14                     LCD_DATA4
 23                        IO21                     LCD_DATA5
 24                        IO47                     LCD_DATA6
 25                        IO48                     LCD_DATA7
 26                        IO45                     LCD_DATA8
 27                        IO0                      BOOT
 28                        IO35                     No connection
 29                        IO36                     No connection
 30                        IO37                     No connection
 31                        IO38                     LCD_DATA9
 32                        IO39                     LCD_DATA10
 33                        IO40                     LCD_DATA11
 34                        IO41                     LCD_DATA12
 35                        IO42                     LCD_DATA13
 36                        RXD0                     UART_RXD0
                                                                                        continues on next page


Espressif Systems                                  58                                               Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


                                   Table 3 – continued from previous page
 Pin                      Pin Name                  Function
 37                       TXD0                      UART_TXD0
 38                       IO2                       LCD_DATA14
 39                       IO1                       LCD_DATA15
 40                       GND                       GND
 41                       EPAD                      GND


The pins on the I/O expander connected to the module can be used for different functions.

                                     Table 4: I/O Expander GPIO Allocation
 IO Expander Pin                  Pin Name                        Function
 1                                A0                              GND
 2                                A1                              GND
 3                                A2                              GND
 4                                P0                              PA_CTRL
 5                                P1                              LCD_SPI_CS
 6                                P2                              LCD_SPI_SCK
 7                                P3                              LCD_SPI_MOSI
 8                                GND                             GND
 9                                P4                              Free
 10                               P5                              Free
 11                               P6                              Free
 12                               P7                              Free
 13                               INT                             No connection
 14                               SCL                             I2C_SCL
 15                               SDA                             I2C_SDA
 16                               VCC                             Supply voltage


Power Distribution


Power Supply over USB There are two ways to power the development board via USB power port.
    • Via USB-to-USB port




                        Fig. 30: ESP32-S3-LCD-EV-Board - USB-to-USB Power Supply



Espressif Systems                                  59                                       Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


   • Via USB-to-UART port




                       Fig. 31: ESP32-S3-LCD-EV-Board - USB-to-UART Power Supply


Independent Audio and Digital Power Supply ESP32-S3-LCD-EV-Board features independent power supplies
for the audio components and ESP module. This should reduce noise in the audio signal from digital components and
improve the overall performance of the components.




                           Fig. 32: ESP32-S3-LCD-EV-Board - Digital Power Supply


AEC Path The acoustic echo cancellation (AEC) path provides reference signals for AEC algorithm.
ESP32-S3-LCD-EV-Board provides two compatible echo reference signal source designs. One is Codec (ES8311)
DAC output (DAC_AOUTLP/DAC_AOUTLP), the other is PA (NS4150) output (PA_OUT+/PA_OUT+). The
former is a default and the recommended selection. Resistors R54 and R56 shown in the figure below should not be
installed.
The echo reference signal is collected by ADC_MIC3P/ADC_MIC3N of ADC (ES7210) and then sent back to
ESP32-S3 for AEC algorithm.


Hardware Setup Options


Espressif Systems                                 60                                              Release master
                                       Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                         Fig. 33: ESP32-S3-LCD-EV-Board - Audio Power Supply




               Fig. 34: ESP32-S3-LCD-EV-Board - AEC Codec DAC Output (Click to Enlarge)




Espressif Systems                             61                                          Release master
                                   Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




                    Fig. 35: SP32-S3-LCD-Ev-Board - AEC PA Output (Click to Enlarge)




           Fig. 36: ESP32-S3-LCD-EV-Board - AEC Reference Signal Collection (Click to Enlarge)




Espressif Systems                              62                                          Release master
                                    Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board


Automatic Download There are two ways to put the development board into the download mode.
    • Press the Boot and Reset buttons. Release the Reset button first and then the Boot button.
    • The download is performed automatically by the software. The software uses the DTR and RTS signals from
      the serial port to control the status of the EN and IO0 pins.


Hardware Revision Details No previous revisions.


Sample Request This development board with the USB Type-A adapter is suitable for evaluating Espressif s
high-performance HMI Smart Displays Solution. For placing orders, please proceed to the Espressif Online Shop.


Related Documents Please download the following documents from the HTML version of esp-dev-kits Documen-
tation.
    • ESP32-S3 Datasheet
    • ESP32-S3-WROOM-1 Datasheet
    • ESP Product Selector
    • ESP32-S3-LCD-EV-Board-MB Schematics
    • ESP32-S3-LCD-EV-Board-MB PCB Layout
    • ESP32-S3-LCD-EV-Board-SUB1 Schematics
    • ESP32-S3-LCD-EV-Board-SUB1 PCB Layout
    • ESP32-S3-LCD-EV-Board-SUB2 Schematics
    • ESP32-S3-LCD-EV-Board-SUB2 PCB Layout
    • ESP32-S3-LCD-EV-Board-SUB3 Schematics
    • ESP32-S3-LCD-EV-Board-SUB3 PCB Layout
    • ESP32-S3-LCD-EV-Board USB Adapter Schematics
    • ESP32-S3-LCD-EV-Board USB Adapter PCB Layout
    • TCA9554 Datasheet
For further design documentation for the board, please contact us at sales@espressif.com.




Espressif Systems                                  63                                          Release master
                                        Submit Document Feedback


---

Chapter 3. ESP32-S3-LCD-EV-Board




Espressif Systems                             64              Release master
                                   Submit Document Feedback


---

Chapter 4

ESP-VoCat


ESP-VoCat is an intelligent AI development kit. It is suitable for voice interaction products that require large model
capabilities, such as toys, smart speakers, and smart central control systems. The device is equipped with an ESP32-
S3 module, a 1.85-inch QSPI circular touch screen, dual microphone array, and supports offline voice wake-up and
sound source localization algorithms. Combined with the large model capabilities provided by OpenAI Xiaozhi
AI, Gemini, etc., ESP-VoCat can achieve full-duplex voice interaction, multimodal recognition, and intelligent agent
control, providing a solid foundation for developers to create complete edge-side AI application experiences.
Application examples for the development board are stored in the esp-brookesia project.


Note: Please check the silkscreen version number on the mainboard to confirm your development board version.
For v1.0 version development boards, please refer to ESP-VoCat v1.0; for v1.2 version development boards, please
refer to ESP-VoCat v1.2.



Tip: For quick-start procedures after powering on ESP-VoCat, refer to the ESP-VoCat Built-in Firmware User
Guide.




4.1     ESP-VoCat v1.2



Note: Please check the silkscreen version number on the mainboard to confirm your development board version.
For v1.0 version development boards, please refer to ESP-VoCat v1.0; For v1.2 version development boards, please
refer to the current user guide.



Tip: For quick-start procedures after powering on ESP-VoCat, refer to the ESP-VoCat Built-in Firmware User
Guide.


This guide will help you get started with ESP-VoCat quickly and provide detailed information about this development
board.
ESP-VoCat is an intelligent AI development kit. It is suitable for voice interaction products that require large model
capabilities, such as toys, smart speakers, and smart central control systems. The device is equipped with an ESP32-
S3-WROOM-1 module, a 1.85-inch QSPI circular touch screen, dual microphone array, and supports offline voice
wake-up and sound source localization algorithms. Combined with the large model capabilities provided by Amazon


                                                                                                                   65


---

Chapter 4. ESP-VoCat


Nova, OpenAI, Xiaozhi AI, Gemini, etc. ESP-VoCat can achieve full-duplex voice interaction, multimodal recog-
nition, and intelligent agent control, providing a solid foundation for developers to create complete edge-side AI
application experiences.
ESP-VoCat s main controller uses the Espressif ESP32-S3-WROOM-1-N16R16VA module, supporting 2.4 GHz
Wi-Fi and Bluetooth 5 (LE) wireless connectivity. For storage, the entire device has 16MB PSRAM and 16MB
Flash storage space, and is also equipped with a microSD card slot that can support up to 32GB, meeting the needs
of voice interaction and multimedia processing. It features a 1.85-inch circular touch screen (360 × 360 resolution)
with ESP32-S3 native touch sensors, providing an intuitive and rich interactive experience.
For audio, ESP-VoCat has a built-in 3W speaker and dual microphone array, supporting local voice wake-up and
sound source localization. The power system is compatible with 5 V DC and 3.7 V lithium battery power supply.
Additionally, it integrates a USB-C interface for power supply and programming download, while reserving a Pogopin
interface for convenient functional expansion.




                                 Fig. 1: ESP-VoCat Front View (Click to enlarge)

The document consists of the following major sections:
    • Getting Started: Overview of the board and hardware/software setup instructions to get started.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: Hardware revision history and known issues (if any) of the board.
    • Related Documents: Links to related documentation.


4.1.1    Getting Started

This section provides a brief introduction of ESP-VoCat, instructions on how to do the initial hardware setup and
how to flash firmware onto it.


Description of Components

The following introduces the main components on the front PCB in clockwise order. For user convenience, we have
also labeled these components or interfaces on the ESP-VoCat housing.


Espressif Systems                                  66                                               Release master
                                        Submit Document Feedback


---

Chapter 4. ESP-VoCat




                               Fig. 2: ESP-VoCat Back View (Click to enlarge)




                       Fig. 3: ESP-VoCat CoreBoard PCB Front View (Click to enlarge)




Espressif Systems                               67                                     Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 4: ESP-VoCat MicBoard PCB Front View (Click to enlarge)




                       Fig. 5: ESP-VoCat BaseBoard PCB Front View (Click to enlarge)




Espressif Systems                               68                                     Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat




                            Fig. 6: ESP-VoCat Front View (Click to enlarge)



 Main Components              Description
 CoreBoard
 ESP32-S3-WROOM-1-            Main controller chip, integrates 16 MB Flash and 16 MB PSRAM, supports
 N16R16VA                     2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity.
 Battery Connector            Battery connector for connecting 3.7 V lithium battery, top is positive, bottom
                              is negative.
 LCD FPC Connector            For connecting 1.85-inch circular LCD screen with 360 x 360 resolution. For
                              detailed parameters, please refer to the Display Specification.
 MicBoard Connector           MicBoard PCB connector, connects dual microphone array and status indicator
                              LED.
 Touch Connector              Touch connector for connecting touch copper foil to achieve touch interaction
                              functionality.
 Speaker Connector            2-wire speaker connector for connecting built-in 3 W speaker.
 MicBoard
 Green LED                    Green LED indicator.
 MIC (Microphone Array)       Dual LMA3729T381-OY3S microphone array, supports local voice wake-up
                              and sound source localization functionality.
 BaseBoard
 BQ27220 (Battery Manage-     Battery management chip for battery level detection, charging management,
 ment Chip)                   and power status monitoring.
 TP4057 (Lithium Battery      Lithium battery charging chip for charging lithium batteries with 250 mA
 Charging Chip)               charging current.
 CoreBoard Connector          CoreBoard PCB connector, connects core board with base board.
 TlV62569 (DCDC Chip)         Buck converter chip for converting 5 V power to 3.3 V power, providing stable
                              power supply for the system.
 SAM8108 (Power Control       Power control chip for controlling device power on/off. Single click of POWER
 Chip)                        button can toggle power on/off status.
 Type-C (USB-C Interface)     USB-C interface for power supply, programming download, and debugging,
                              supports charging lithium batteries.
Espressif Systems                                  69                                            Release master
                                  Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 7: ESP-VoCat CoreBoard PCB Back View (Click to enlarge)




                        Fig. 8: ESP-VoCat MicBoard PCB Back View (Click to enlarge)

The following introduces the main components on the back PCB in clockwise order. For user convenience, we have
also labeled these components or interfaces on the ESP-VoCat housing.




Espressif Systems                                70                                            Release master
                                      Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 9: ESP-VoCat BaseBoard PCB Back View (Click to enlarge)




                              Fig. 10: ESP-VoCat Back View (Click to enlarge)



Espressif Systems                               71                                    Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat




 Main Components                   Description
 CoreBoard
 NS4150B (Class D Amplifier)       Ultra-low EMI, filterless, 3W mono Class D audio amplifier.
 ES7210 (Audio Decoder Chip)       High-performance 4-channel audio decoder chip, supports I2S/PDM/TDM
                                   data ports.
 SY8088AAC (DCDC chip)             Buck converter chip used to convert a 5 V power supply to a 3.3 V power supply,
                                   providing stable power for the Codec.
 BaseBoard Connector               Base board connector for connecting base board with CoreBoard.
 BMI270 (IMU - Inertial Mea-       6-axis intelligent low-power inertial measurement unit for high-performance
 surement Unit)                    applications.
 ES8311 (Audio Codec Chip)         Low-power mono audio codec with high-performance multi-bit Delta-Sigma
                                   audio ADC and DAC.
 MicBoard
 FPC Connector                     Connects MicBoard with CoreBoard FPC connector.
 BaseBoard
 M1.6 Welded Nut                   For fixing main board to housing.
 RST Button (Reset Button)         For resetting the main board.
 Magnetic Connector                For functional expansion, provides a serial port and 5 V power interface, can
                                   connect to rotating base and other devices.
 POWER Switch                      For controlling device power on/off. Single click of POWER button can toggle
                                   power on/off status.
 BOOT Button                       When powering on, hold this button to enter download mode.
 SD Card Slot                      Supports up to 32 GB microSD card slot for storing audio, images, videos, and
                                   other data.


Start Application Development

Before powering on, please ensure ESP-VoCat is intact and undamaged.


Required Hardware
    • ESP-VoCat
    • USB data cable
    • Computer (Windows, Linux, or macOS)


Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed
data lines nor work for programming the boards.



Hardware Setup Use a USB data cable to connect ESP-VoCat to your computer through the Type-C (USB-C
Interface) for firmware burning, debugging, and power supply.


Software Setup Please proceed to ESP-IDF Get Started to set up the development environment and flash an ap-
plication example onto your board.


Note: In most cases, USB drivers required to operate the board are already included in Windows, Linux, and macOS
operating systems. Some additional port access or security configuration may be required depending on your OS. In
case of issues, please check documentation on how to establish serial connection with the board. The documentation
also includes links to USB drivers applicable to boards produced by Espressif.




Espressif Systems                                 72                                                Release master
                                       Submit Document Feedback


---

Chapter 4. ESP-VoCat


Espressif provides Board Support Packages (BSPs) for various Espressif boards that help you initialize and use key
onboard peripherals, such as LCD displays, audio chips, buttons, and LEDs, more easily and efficiently. For a com-
plete list of supported boards, please visit esp-bsp.
Development board application examples are stored in the esp-brookesia project.


4.1.2    Hardware Reference

Block Diagram

The block diagram below shows the components of ESP-VoCat and their interconnections.




                              Fig. 11: ESP-VoCat Block Diagram (Click to enlarge)


Power Supply Options

There are three mutually exclusive ways to provide power to the board:
   1. Power through Type-C (USB-C Interface)
      When using this method, connect the device s Type-C interface using a USB Type-C data cable. If a lithium
      battery is installed, you need to press the POWER button to enable power supply to the device.
   2. Power through Magnetic Connector
      When using this method, connect the device to the corresponding magnetic connector base to power the device.
      If a lithium battery is installed, you need to press the POWER button to enable power supply to the device.


   3. Power through Battery
      The device has an integrated 3.7 V lithium battery. Press the POWER button to power the device.
Any of the above external power supply methods can charge the internal lithium battery.


Type-C Interface

Magnetic Connector Interface




Espressif Systems                                 73                                               Release master
                                       Submit Document Feedback


---

Chapter 4. ESP-VoCat




                             Fig. 12: Magnetic Connector (Click to enlarge)




                       Fig. 13: Type-C Interface Circuit Diagram (Click to enlarge)




Espressif Systems                             74                                      Release master
                                   Submit Document Feedback


---

Chapter 4. ESP-VoCat




                    Fig. 14: Magnetic Connector Interface Circuit Diagram (Click to enlarge)




                           Fig. 15: LCD Interface Circuit Diagram (Click to enlarge)




Espressif Systems                                 75                                           Release master
                                       Submit Document Feedback


---

Chapter 4. ESP-VoCat


LCD Interface

Please note that the CN3 interface is reserved for other screen compatibility and is currently not enabled.
The U2 interface is the officially used LCD screen interface. The screen model used by this development board is
ST77916, LCD: 1.85 , 360 x 360, ST77916, QSPI Interface. LCD_BLK (GPIO44) can be used to control screen
backlight.


SD Card Interface




                           Fig. 16: SD Card Interface Circuit Diagram (Click to enlarge)

Please note that the SD card interface supports:
    • 1-wire SD bus configuration
    • Communication through SDIO protocol


Power Switch Circuit




                             Fig. 17: Power Switch Circuit Diagram (Click to enlarge)



Charging Circuit




Espressif Systems                                   76                                                Release master
                                         Submit Document Feedback


---

Chapter 4. ESP-VoCat




                             Fig. 18: Charging Circuit Diagram (Click to enlarge)




                       Fig. 19: Battery Management Circuit Diagram (Click to enlarge)




                       Fig. 20: Microphone Interface Circuit Diagram (Click to enlarge)




Espressif Systems                               77                                        Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat


Microphone Interface

4.1.3    Hardware Revision Details

ESP-VoCat v1.2

    • The following pins have been reassigned:
        – U1RXD: Changed from IO5 to IO4
        – U1TXD: Changed from IO6 to IO5
        – I2S_DI: Changed from IO15 to IO3
        – PA_CTRL: Changed from IO4 to IO15
        – LCD_RST_CTRL: Changed from IO3 to IO47
    • TOUCH interface increased from 1 to 2 for sliding touch sensing:
        – TOUCH_PAD1: IO6
        – TOUCH_PAD2: IO7
    • Added CODEC power control:
        – CODEC_PWR_CTRL: IO48
    • Added IIC expansion interface:
        – Added HC-1.25-4PLT interface: Exposes VIN, I2C_SDA, I2C_SCL, and GND


ESP-VoCat v1.0

    • Initial Release


4.1.4    Related Documents

    • ESP-VoCat V1.2 Schematic (PDF)
    • ESP-VoCat V1.2 PCB Layout (PDF)
    • Display Specification (PDF)
    • ESP-VoCat Built-in Firmware User Guide (HTML)


ESP-VoCat v1.0




Note: Please check the silkscreen version number on the mainboard to confirm your development board version.
For v1.0 version development boards, please refer to the current user guide; for v1.2 version development boards,
please refer to ESP-VoCat v1.2.



Tip: For quick-start procedures after powering on ESP-VoCat, refer to the ESP-VoCat Built-in Firmware User
Guide.


This guide will help you get started with ESP-VoCat quickly and provide detailed information about this development
board.
ESP-VoCat is an intelligent AI development kit. It is suitable for voice interaction products that require large model
capabilities, such as toys, smart speakers, and smart central control systems. The device is equipped with an ESP32-
S3-WROOM-1 module, a 1.85-inch QSPI circular touch screen, dual microphone array, and supports offline voice
wake-up and sound source localization algorithms. Combined with the large model capabilities provided by Amazon
Nova, OpenAI, Xiaozhi AI, Gemini, etc. ESP-VoCat can achieve full-duplex voice interaction, multimodal recog-
nition, and intelligent agent control, providing a solid foundation for developers to create complete edge-side AI
application experiences.




Espressif Systems                                   78                                                Release master
                                         Submit Document Feedback


---

Chapter 4. ESP-VoCat


ESP-VoCat s main controller uses the Espressif ESP32-S3-WROOM-2-N32R16V module, supporting 2.4 GHz
Wi-Fi and Bluetooth 5 (LE) wireless connectivity. For storage, the entire device has 16 MB PSRAM and 32 MB
Flash storage space, and is also equipped with a microSD card slot that can support up to 32 GB, meeting the needs
of voice interaction and multimedia processing. It features a 1.85-inch circular touch screen (360 × 360 resolution)
with ESP32-S3 native touch sensors, providing an intuitive and rich interactive experience.
For audio, ESP-VoCat has a built-in 3W speaker and dual microphone array, supporting local voice wake-up and
sound source localization. The power system is compatible with 5 V DC and 3.7 V lithium battery power supply.
Additionally, it integrates a USB-C interface for power supply and programming download, while reserving a Pogopin
interface for convenient functional expansion.




                                Fig. 21: ESP-VoCat Front View (Click to enlarge)

The document consists of the following major sections:
    • Getting Started: Overview of the board and hardware/software setup instructions to get started.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: Hardware revision history and known issues (if any) of the board.
    • Related Documents: Links to related documentation.


Getting Started This section provides a brief introduction of ESP-VoCat, instructions on how to do the initial
hardware setup and how to flash firmware onto it.


Description of Components The following introduces the main components on the front PCB in clockwise order.
For user convenience, we have also labeled these components or interfaces on the ESP-VoCat housing.




Espressif Systems                                  79                                               Release master
                                        Submit Document Feedback


---

Chapter 4. ESP-VoCat




                               Fig. 22: ESP-VoCat Back View (Click to enlarge)




                       Fig. 23: ESP-VoCat CoreBoard PCB Front View (Click to enlarge)




Espressif Systems                                80                                     Release master
                                      Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 24: ESP-VoCat MicBoard PCB Front View (Click to enlarge)




                       Fig. 25: ESP-VoCat BaseBoard PCB Front View (Click to enlarge)




Espressif Systems                               81                                      Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat




                          Fig. 26: ESP-VoCat Front View (Click to enlarge)



 Main Components             Description
 CoreBoard
 ESP32-S3-WROOM-2-           Main controller chip, integrates 32 MB Flash and 16 MB PSRAM, supports
 N32R16V                     2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity.
 Battery Connector           Battery connector for connecting 3.7 V lithium battery, top is positive, bottom
                             is negative.
 LCD FPC Connector           For connecting 1.85-inch circular LCD screen with 360 x 360 resolution. For
                             detailed parameters, please refer to the Display Specification.
 MicBoard Connector          MicBoard PCB connector, connects dual microphone array and status indicator
                             LED.
 Touch Connector             Touch connector for connecting touch copper foil to achieve touch interaction
                             functionality.
 Speaker Connector           2-wire speaker connector for connecting built-in 3 W speaker.
 MicBoard
 Green LED                   Green LED indicator.
 MIC (Microphone Array)      Dual LMA3729T381-OY3S microphone array, supports local voice wake-up
                             and sound source localization functionality.
 BaseBoard
 BQ27220 (Battery Manage-    Battery management chip for battery level detection, charging management,
 ment Chip)                  and power status monitoring.
 TP4057 (Lithium Battery     Lithium battery charging chip for charging lithium batteries with 250 mA
 Charging Chip)              charging current.
 CoreBoard Connector         CoreBoard PCB connector, connects core board with base board.
 TlV62569 (DCDC Chip)        Buck converter chip for converting 5 V power to 3.3 V power, providing stable
                             power supply for the system.
 SAM8108 (Power Control      Power control chip for controlling device power on/off. Single click of POWER
 Chip)                       button can toggle power on/off status.
 Type-C (USB-C Interface)    USB-C interface for power supply, programming download, and debugging,
                             supports charging lithium batteries.
Espressif Systems                                 82                                            Release master
                                 Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 27: ESP-VoCat CoreBoard PCB Back View (Click to enlarge)




                       Fig. 28: ESP-VoCat MicBoard PCB Back View (Click to enlarge)

The following introduces the main components on the back PCB in clockwise order. For user convenience, we have
also labeled these components or interfaces on the ESP-VoCat housing.




Espressif Systems                                83                                            Release master
                                      Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 29: ESP-VoCat BaseBoard PCB Back View (Click to enlarge)




                              Fig. 30: ESP-VoCat Back View (Click to enlarge)


Espressif Systems                               84                                     Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat




 Main Components                   Description
 CoreBoard
 NS4150B (Class D Amplifier)       Ultra-low EMI, filterless, 3W mono Class D audio amplifier.
 ES7210 (Audio Decoder Chip)       High-performance 4-channel audio decoder chip, supports I2S/PDM/TDM
                                   data ports.
 BaseBoard Connector               Base board connector for connecting base board with CoreBoard.
 BMI270 (IMU - Inertial Mea-       6-axis intelligent low-power inertial measurement unit for high-performance
 surement Unit)                    applications.
 ES8311 (Audio Codec Chip)         Low-power mono audio codec with high-performance multi-bit Delta-Sigma
                                   audio ADC and DAC.
 MicBoard
 FPC Connector                     Connects MicBoard with CoreBoard FPC connector.
 BaseBoard
 M1.6 Welded Nut                   For fixing main board to housing.
 RST Button (Reset Button)         For resetting the main board.
 Magnetic Connector                For functional expansion, provides a serial port and 5 V power interface, can
                                   connect to rotating base and other devices.
 POWER Switch                      For controlling device power on/off. Single click of POWER button can toggle
                                   power on/off status.
 BOOT Button                       When powering on, hold this button to enter download mode.
 SD Card Slot                      Supports up to 32 GB microSD card slot for storing audio, images, videos, and
                                   other data.


Start Application Development Before powering on, please ensure ESP-VoCat is intact and undamaged.


Required Hardware
    • ESP-VoCat
    • USB data cable
    • Computer (Windows, Linux, or macOS)


Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed
data lines nor work for programming the boards.



Hardware Setup Use a USB data cable to connect ESP-VoCat to your computer through the Type-C (USB-C
Interface) for firmware burning, debugging, and power supply.


Software Setup Please proceed to ESP-IDF Get Started to set up the development environment and flash an ap-
plication example onto your board.


Note: In most cases, USB drivers required to operate the board are already included in Windows, Linux, and macOS
operating systems. Some additional port access or security configuration may be required depending on your OS. In
case of issues, please check documentation on how to establish serial connection with the board. The documentation
also includes links to USB drivers applicable to boards produced by Espressif.


Espressif provides Board Support Packages (BSPs) for various Espressif boards that help you initialize and use key
onboard peripherals, such as LCD displays, audio chips, buttons, and LEDs, more easily and efficiently. For a com-
plete list of supported boards, please visit esp-bsp.
Development board application examples are stored in the esp-brookesia project.




Espressif Systems                                 85                                               Release master
                                       Submit Document Feedback


---

Chapter 4. ESP-VoCat


Hardware Reference


Block Diagram The block diagram below shows the components of ESP-VoCat and their interconnections.




                              Fig. 31: ESP-VoCat Block Diagram (Click to enlarge)


Power Supply Options There are three mutually exclusive ways to provide power to the board:
   1. Power through Type-C (USB-C Interface)
      When using this method, connect the device s Type-C interface using a USB Type-C data cable. If a lithium
      battery is installed, you need to press the POWER button to enable power supply to the device.
   2. Power through Magnetic Connector
      When using this method, connect the device to the corresponding magnetic connector base to power the device.
      If a lithium battery is installed, you need to press the POWER button to enable power supply to the device.


   3. Power through Battery
      The device has an integrated 3.7 V lithium battery. Press the POWER button to power the device.
Any of the above external power supply methods can charge the internal lithium battery.


Type-C Interface


Magnetic Connector Interface


LCD Interface Please note that the CN3 interface is reserved for other screen compatibility and is currently not
enabled.
The U2 interface is the officially used LCD screen interface. The screen model used by this development board is
ST77916, LCD: 1.85 , 360 x 360, ST77916, QSPI Interface. LCD_BLK (GPIO44) can be used to control screen
backlight.


SD Card Interface Please note that the SD card interface supports:
    • 1-wire SD bus configuration
    • Communication through SDIO protocol




Espressif Systems                                 86                                               Release master
                                       Submit Document Feedback


---

Chapter 4. ESP-VoCat




                                Fig. 32: Magnetic Connector (Click to enlarge)




                          Fig. 33: Type-C Interface Circuit Diagram (Click to enlarge)




                    Fig. 34: Magnetic Connector Interface Circuit Diagram (Click to enlarge)


Espressif Systems                                 87                                           Release master
                                       Submit Document Feedback


---

Chapter 4. ESP-VoCat




                        Fig. 35: LCD Interface Circuit Diagram (Click to enlarge)




                       Fig. 36: SD Card Interface Circuit Diagram (Click to enlarge)




                         Fig. 37: Power Switch Circuit Diagram (Click to enlarge)


Espressif Systems                              88                                      Release master
                                    Submit Document Feedback


---

Chapter 4. ESP-VoCat


Power Switch Circuit




                            Fig. 38: Charging Circuit Diagram (Click to enlarge)




                       Fig. 39: Battery Management Circuit Diagram (Click to enlarge)

Charging Circuit


Microphone Interface


Hardware Revision Details No historical versions.


Related Documents
   • ESP-VoCat V1.0 Schematic (PDF)
   • ESP-VoCat V1.0 PCB Layout (PDF)
   • Display Specification (PDF)
   • Replication Tutorial (HTML)
   • ESP-VoCat Built-in Firmware User Guide (HTML)




Espressif Systems                               89                                      Release master
                                     Submit Document Feedback


---

Chapter 4. ESP-VoCat




                       Fig. 40: Microphone Interface Circuit Diagram (Click to enlarge)




Espressif Systems                               90                                        Release master
                                     Submit Document Feedback


---

Chapter 5

ESP-DualKey


ESP-DualKey is an intelligent dual-key controller development board based on the ESP32-S3 chip developed by
Espressif. It integrates smart home control, Bluetooth keyboard, USB keyboard, and other functions, and can switch
between different working modes through physical switches. The development board features dual buttons, RGB
lighting effects, battery management, power monitoring, and other functions, providing developers with a complete
intelligent button solution.
Application examples for the development board are stored in the Examples folder.


5.1     ESP-DualKey



Note: Please check the silkscreen version number on the main board to confirm your development board version.


This user guide will help you get started with ESP-DualKey and will also provide more in-depth information.
ESP-DualKey is an intelligent dual-key controller development board developed by Espressif based on the ESP32-S3
chip, integrating smart home control, Bluetooth keyboard, USB keyboard and other functions. It can switch between
different working modes through physical switches. The development board is equipped with dual buttons, RGB
lighting effects, battery management, power monitoring and other functions, providing developers with a complete
intelligent button solution.
The ESP-DualKey main controller uses the Espressif ESP32-S3 chip, supporting 2.4 GHz Wi-Fi and Bluetooth 5
(LE) wireless connectivity. In terms of storage, the entire device has 8 MB flash storage space to meet the needs of
intelligent button applications. It is equipped with a dual-button matrix and WS2812 RGB lighting effects, providing
an intuitive and rich interactive experience.
In terms of power supply, ESP-DualKey supports USB-C power supply and built-in lithium battery power supply,
integrating battery management chips and power monitoring functions. In addition, it also integrates a USB-C in-
terface that supports power supply and programming download, while providing multiple working mode switching
functions.
The document consists of the following major sections:
    • Getting Started: Overview of the board and hardware/software setup instructions to get started.
    • Hardware Reference: More detailed information about the board s hardware.
    • Hardware Revision Details: Hardware revision history and known issues (if any) of the board.
    • Related Documents: Links to related documentation.




                                                                                                                 91


---

Chapter 5. ESP-DualKey




                               Fig. 1: ESP-DualKey Front View (Click to enlarge)



Note: For instructions on using the factory firmware, please refer to ESP-DualKey User Guide.



5.1.1    Getting Started

This section provides a brief introduction of ESP-DualKey, instructions on how to do the initial hardware setup and
how to flash firmware onto it.


Feature List

The main features of the board are listed below:
Button Matrix Configuration:
    • 2×1 matrix configuration
    • Supports independent button detection
    • Supports combination button functions
RGB LED Features:
    • WS2812 programmable RGB LED
    • Supports multiple lighting effect modes
    • Supports brightness, hue, and saturation adjustment
Mode Switch:
    • Left Position: Bluetooth keyboard mode
    • Middle Position: USB keyboard mode
    • Right Position: Smart home mode (ESP RainMaker)


Description of Components

The key components of the board are described below. For user convenience, the components or interfaces are also
labeled on the housing of ESP-DualKey.




Espressif Systems                                  92                                               Release master
                                        Submit Document Feedback


---

Chapter 5. ESP-DualKey




 Key Component                      Description
 Main Controller
 ESP32-S3                           Main controller chip supporting 2.4 GHz Wi-Fi and Bluetooth 5 (LE) connec-
                                    tivity, and featuring 8 MB of integrated flash storage.
 Interaction
 Dual Buttons                       2×1 button matrix, supports independent key detection and combination key
                                    functions.
 Mode Switch                        Three-position switch for toggling between operating modes (Bluetooth
                                    keyboard/Wi-Fi Mode/USB keyboard).
 RGB Lighting
 WS2812 RGB LED                     Programmable RGB LED supporting diverse lighting effects, e.g., heat map,
                                    breathing effect, flowing effect.
 Power Management
 Lithium Battery Charging Chip      TP4057 lithium battery charging management, supports USB-C charging.
 Interfaces
 USB-C Port                         USB-C for power, programming/download, debugging, and battery charging.
 Two HY2.0-4P Ports                 Support auxiliary power output for connecting external sensors.
 Other Components
 Battery Voltage Monitoring         Real-time battery voltage and charging status monitoring.
 VBUS Monitoring                    Monitors USB power status.
 Deep-sleep                         Supports Deep-sleep mode for energy saving.


Application Examples

The following application examples are available for ESP-DualKey:
    • ESP-DualKey Smart Button Controller Example - Demonstrates the use of the ESP-DualKey development
      board as a smart button controller with smart home control, Bluetooth keyboard, and USB keyboard function-
      alities, allowing for mode switching through physical switches.
    • test_apps - Provides unit tests for the esp_hid component on ESP32 and ESP32-C3 chips, allowing developers
      to validate the functionality of their code and add new test cases as needed.
For more examples and the latest updates, please refer to the examples folder.
To explore the application examples or to develop your own, please follow the steps outlined in the Start Developing
Applications section.


Start Developing Applications

Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.


Required Hardware
    • ESP-DualKey
    • USB 2.0 cable (Standard-A to Type-C)
    • Computer running Windows, Linux, or macOS

Note: Please ensure you use an appropriate USB data cable. Some cables can only be used for charging and cannot
be used for data transmission and programming.



Hardware Setup Connect ESP-DualKey with the computer using a USB data cable through the USB-C inter-
face for firmware flashing, debugging and power supply.




Espressif Systems                                  93                                               Release master
                                        Submit Document Feedback


---

Chapter 5. ESP-DualKey


Software Setup Please proceed to ESP-IDF Get Started to set up the development environment and flash an ap-
plication example onto your board.


Note: In most cases USB drivers required to operate the board are already included in Windows, Linux, and macOS
operating systems. Some additional port access or security configuration may be required depending on your OS. In
case of issues please check documentation on how to establish serial connection with the board. The documentation
also includes links to USB drivers applicable to boards produced by Espressif.


Espressif provides Board Support Packages (BSPs) for various Espressif boards that help you initialize and use key
onboard peripherals, such as LCD displays, audio chips, buttons, and LEDs, more easily and efficiently. For a com-
plete list of supported boards, please visit esp-bsp.


5.1.2    Hardware Reference

Block Diagram

The block diagram below shows the components of ESP-DualKey and their interconnections.




                        Fig. 2: ESP-DualKey Functional Block Diagram (Click to enlarge)


Power Supply Options There are two mutually exclusive ways to provide power to the board:
   1. Through USB-C interface power supply
      When using this method for power supply, use a USB Type-C data cable to connect to the USB-C interface on
      the device.
   2. Through built-in lithium battery power supply
      The device has an integrated lithium battery inside, supporting independent power supply operation.


Mode Switch Circuit The mode switch circuit diagram of the board is shown below.




Espressif Systems                                 94                                               Release master
                                       Submit Document Feedback


---

Chapter 5. ESP-DualKey




                                Fig. 3: Mode Switch Circuit Diagram (Click to enlarge)


5.1.3    Hardware Revision Details

This is the first revision of this board released.


5.1.4    Related Documents

    • ESP-DualKey Schematic (PDF)
    • User Guide (HTML)




Espressif Systems                                     95                                 Release master
                                           Submit Document Feedback


---

Chapter 5. ESP-DualKey




Espressif Systems                   96              Release master
                         Submit Document Feedback


---

Chapter 6

EOL (End of Life) Boards


This section contains user guides for the ESP32-S3 end-of-life development boards and is provided for reference only.
While these boards may still be available on the market or used in legacy systems, they no longer receive updates,
bug fixes, or official support. It is recommended to switch to newer development boards for better performance and
more features.


6.1     ESP32-S3-DevKitM-1



Note: As the ESP32-S3-DevKitM-1 development board offers essentially the same functionality and applications as
ESP32-S3-DevKitC-1-N8R8 and ESP32-S3-DevKitC-1U-N8R8, its production has been discontinued. Developers
may use ESP32-S3-DevKitC-1-N8R8 or ESP32-S3-DevKitC-1U-N8R8 for software and basic function testing (refer
to ESP32-S3-DevKitC-1 User Guide). This change does not affect the supply of the ESP32-S3-MINI-1/1U modules
used on the board.

The ESP32-S3-DevKitM-1 is an entry-level development board equipped with either ESP32-S3-MINI-1 or ESP32-
S3-MINI-1U, a module named for its small size. This board integrates complete Wi-Fi and Bluetooth® Low Energy
functions.
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing.
Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitM-1 on a breadboard.


6.1.1    ESP32-S3-DevKitM-1



Note: As the ESP32-S3-DevKitM-1 development board offers essentially the same functionality and applications as
ESP32-S3-DevKitC-1-N8R8 and ESP32-S3-DevKitC-1U-N8R8, its production has been discontinued. Developers
may use ESP32-S3-DevKitC-1-N8R8 or ESP32-S3-DevKitC-1U-N8R8 for software and basic function testing (refer
to ESP32-S3-DevKitC-1 User Guide). This change does not affect the supply of the ESP32-S3-MINI-1/1U modules
used on the board.

This user guide will help you get started with ESP32-S3-DevKitM-1 and will also provide more in-depth information.
The ESP32-S3-DevKitM-1 is an entry-level development board equipped with either ESP32-S3-MINI-1 or ESP32-
S3-MINI-1U, a module named for its small size. This board integrates complete Wi-Fi and Bluetooth® Low Energy
functions.


                                                                                                                   97


---

Chapter 6. EOL (End of Life) Boards


Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing.
Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitM-1 on a breadboard.




                          Fig. 1: ESP32-S3-DevKitM-1 with ESP32-S3-MINI-1 Module

The document consists of the following major sections:
    • Getting Started: Overview of the board and hardware/software setup instructions to get started.
    • Hardware Reference: More detailed information about the board s hardware.
    • Related Documents: Links to related documentation.


Getting Started

This section provides a brief introduction of ESP32-S3-DevKitM-1, instructions on how to do the initial hardware
setup and how to flash firmware onto it.


Description of Components The key components of the board are described in a counter-clockwise direction,
starting from the ESP32-S3-MINI-1/1U module.




Espressif Systems                                   98                                                Release master
                                         Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




                                      Fig. 2: ESP32-S3-DevKitM-1 - front



 Key Component                    Description
 ESP32-S3-MINI-1/1U               ESP32-S3-MINI-1 and ESP32-S3-MINI-1U are two general-purpose Wi-Fi
                                  and Bluetooth Low Energy combo modules that have a rich set of peripherals.
                                  ESP32-S3-MINI-1 comes with a PCB antenna. ESP32-S3-MINI-1U comes
                                  with an external antenna connector. At the core of the modules is ESP32-
                                  S3FN8, a chip equipped with an 8 MB flash. Since flash is packaged in the chip,
                                  rather than integrated into the module, ESP32-S3-MINI-1/1U has a smaller
                                  package size.
 5 V to 3.3 V LDO                 Power regulator that converts a 5 V supply into a 3.3 V output.
 Pin Headers                      All available GPIO pins (except for the SPI bus for flash) are broken out to the
                                  pin headers on the board for easy interfacing and programming. For details,
                                  please see Header Block.
 USB-to-UART Port                 A Micro-USB port used for power supply to the board, for flashing applications
                                  to the chip, as well as for communication with the chip via the on-board USB-
                                  to-UART bridge.
 Boot Button                      Download button. Holding down Boot and then pressing Reset initiates
                                  Firmware Download mode for downloading firmware through the serial port.
 Reset Button                     Press this button to restart ESP32-S3.
 ESP32-S3 USB Port                ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 speci-
                                  fication. The interface is used for power supply to the board, for flashing appli-
                                  cations to the chip, for communication with the chip using USB 1.1 protocols,
                                  as well as for JTAG debugging.
 USB-to-UART Bridge               Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
 RGB LED                          Addressable RGB LED, driven by GPIO48.
 3.3 V Power On LED               Turns on when the USB power is connected to the board.


Start Application Development Before powering up your board, please make sure that it is in good condition with
no obvious signs of damage.


Required Hardware



Espressif Systems                                 99                                                 Release master
                                       Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


    • ESP32-S3-DevKitM-1
    • USB 2.0 cable (Standard-A to Micro-B)
    • Computer running Windows, Linux, or macOS


Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed
data lines nor work for programming the boards.



Hardware Setup Connect the board with the computer using USB-to-UART Port or ESP32-S3 USB Port. In
subsequent steps, USB-to-UART Port will be used by default.


Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel-
opment environment and then flash an application example onto your board.


Contents and Packaging


Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or
any packaging depending on your retailer.
For retail orders, please go to https://www.espressif.com/en/contact-us/get-samples.


Wholesale Orders If you order in bulk, the boards come in large cardboard boxes.
For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.


Hardware Reference

Block Diagram The block diagram below shows the components of ESP32-S3-DevKitM-1 and their interconnec-
tions.




                                 Fig. 3: ESP32-S3-DevKitM-1 (click to enlarge)




Espressif Systems                                  100                                           Release master
                                        Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


Power Supply Options There are three mutually exclusive ways to provide power to the board:
   • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended)
   • 5V and G (GND) pins
   • 3V3 and G (GND) pins


Header Block The two tables below provide the Name and Function of the pins on both sides of the board (J1 and
J3). The pin names are shown in ESP32-S3-DevKitM-1 - front. The numbering is the same as in the Board Schematic
(PDF).


                                                               J1

 No.    Name Type1                     Function
 1      3V3         P                  3.3 V power supply
 2      0           I/O/T              RTC_GPIO0, GPIO0
 3      1           I/O/T              RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
 4      2           I/O/T              RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
 5      3           I/O/T              RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2
 6      4           I/O/T              RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3
 7      5           I/O/T              RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4
 8      6           I/O/T              RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5
 9      7           I/O/T              RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6
 10     8           I/O/T              RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1
 11     9           I/O/T              RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD
 12     10          I/O/T              RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4, SUB-
                                       SPICS0
 13     11          I/O/T              RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5, SUBSPID
 14     12          I/O/T              RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6, SUB-
                                       SPICLK
 15     13          I/O/T              RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7, SUBSPIQ
 16     14          I/O/T              RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS, SUB-
                                       SPIWP
 17     15          I/O/T              RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P
 18     16          I/O/T              RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N
 19     17          I/O/T              RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6
 20     18          I/O/T              RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3
 21     5V          P                  5 V power supply
 22     G           G                  Ground

  1 P: Power supply; I: Input; O: Output; T: High impedance.




Espressif Systems                                          101                                  Release master
                                                Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


    J3
           No.      Name   Type    Function
           1        G      G       Ground
           2        RST    I       EN
           3        46     I/O/T   GPIO46
           4        45     I/O/T   GPIO45
           5        RX     I/O/T   U0RXD, GPIO44, CLK_OUT2
           6        TX     I/O/T   U0TXD, GPIO43, CLK_OUT1
           7        42     I/O/T   MTMS, GPIO42
           8        41     I/O/T   MTDI, GPIO41, CLK_OUT1
           9        40     I/O/T   MTDO, GPIO40, CLK_OUT2
           10       39     I/O/T   MTCK, GPIO39, CLK_OUT3, SUBSPICS1
           11       38     I/O/T   GPIO38, FSPIWP, SUBSPIWP
           12       37     I/O/T   SPIDQS, GPIO37, FSPIQ, SUBSPIQ
           13       36     I/O/T   SPIIO7, GPIO36, FSPICLK, SUBSPICLK
           14       35     I/O/T   SPIIO6, GPIO35, FSPID, SUBSPID
           15       34     I/O/T   SPIIO5, GPIO34, FSPICS0, SUBSPICS0
           16       33     I/O/T   SPIIO4, GPIO33, FSPIHD, SUBSPIHD
           17       26     I/O/T   SPICS1, GPIO26
           18       21     I/O/T   RTC_GPIO21, GPIO21
           19       20     I/O/T   RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
           20       19     I/O/T   RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
           21       48     I/O/T   SPICLK_N, GPIO48, SUBSPICLK_N_DIFF, RGB LED
           22       47     I/O/T   SPICLK_P, GPIO47, SUBSPICLK_P_DIFF

For description of function names, please refer to ESP32-S3 Datasheet (PDF).




                           Fig. 4: ESP32-S3-DevKitM-1 Pin Layout (click to enlarge)

Pin Layout


Espressif Systems                                 102                                 Release master
                                       Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


Hardware Revision Details

This is the first revision of this board released.


Related Documents

    • ESP32-S3 Datasheet (PDF)
    • ESP32-S3-MINI-1 & ESP32-S3-MINI-1U Datasheet (PDF)
    • ESP32-S3-DevKitM-1 Schematic (PDF)
    • ESP32-S3-DevKitM-1 PCB layout (PDF)
    • ESP32-S3-DevKitM-1 Dimensions (PDF)
    • ESP32-S3-DevKitM-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online
    • ESP32-S3-DevKitM-1 Reference Design (ZIP)
For further design documentation for the board, please contact us at sales@espressif.com.


6.2     ESP32-S3-USB-Bridge


ESP32-S3-USB-Bridge can act as an alternative to USB-to-UART chips like CP210x or debuggers by establishing a
bridge between the computer and existing microcontrollers.


6.2.1    ESP32-S3-USB-Bridge


This user guide will help you get started with ESP32-S3-USB-Bridge and will also provide more in-depth information.
The document consists of the following sections:
    • Board Overview: Overview of the board hardware/software
    • Start Application Development: How to set up hardware/software to develop applications
    • Hardware Reference: More detailed information about the board s hardware
    • Hardware Revision Details: This is the first revision of this board released
    • Sample Request: How to get a sample board
    • Related Documents: Links to related documentation


Board Overview

ESP32-S3-USB-Bridge is a development board based on ESP32-S3.
    • The usb_wireless_bridge example can be used to establish a bridge between a computer and the target chip. It
      can emulate a USB composite device and supports multiple functions:
         – USB-to-UART Bridge: realizes serial data transmission and reception between the computer and the
           target chip.
         – JTAG Adapter: realizes duplex JTAG communication between the computer and the target chip.
         – MSC Storage Device: updates firmware by storing the UF2 firmware files in the USB storage device of
           the board.
         – Wireless Bridge: realizes wireless flashing and wireless serial data transmission and reception through
           ESP-NOW.
The development board also supports a USB Type-A interface that is convenient for replacement.




Espressif Systems                                     103                                           Release master
                                           Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




                             Fig. 5: ESP32-S3-USB-Bridge Type-C Connection




                            Fig. 6: ESP32-S3-USB-Bridge Type-A Connection


Espressif Systems                                104                         Release master
                                      Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


Feature List The main features of the board are listed below:
   • Module Embedded: ESP32-S3-MINI-1 module with 4 MB flash and 2 MB PSRAM
   • LED Indicators: on-board WS2812 LED indicator with two serial data LED indicators
   • USB: on-board USB-to-UART bridge and JTAG adapter, with support for USB download/debugging


Block Diagram The block diagram below shows the components of ESP32-S3-USB-Bridge and their intercon-
nections.




                        Fig. 7: ESP32-S3-USB-Bridge Block Diagram (Click to Enlarge)



Description of Components ESP32-S3-USB-Bridge is a rather compact development board, with a dimension
of 23.3 mm * 31.5 mm. It integrates the ESP32-S3-MINI-1 module and offers a 12-pin expansion connector.
The key components of the board are described in a clockwise direction.


 Key Component                     Description
 ESP32-S3-MINI-1-N4R2              ESP32-S3-MINI-1-N4R2 is a generic Wi-Fi + Bluetooth LE MCU module
 Module                            that is built around the ESP32-S3 series of SoCs. It is integrated with 4 MB
                                   flash and 2 MB PSRAM. On top of a rich set of peripherals, the acceleration
                                   for neural network computing and signal processing workloads provided by the
                                   SoC makes the module an ideal choice for a wide variety of application sce-
                                   narios related to Artificial Intelligence of Things (AIoT).
 TX/RX Indicator                   Indicates transmit and receive status of serial data.
 Expansion Connector               Provides connections for JTAG pins, serial pins, TX/RX pins, Boot pins, Reset
                                   pins, and power supply pins.
 Reset Button                      Connects the Reset button on the target chip and IO8 on the module. Press this
                                   button to reset the target chip.
 USB-to-USB Port                   Provides power to the entire system. Used for USB communication between
                                   the PC and the ESP32-S3-MINI-1 module.
 Boot Button                       Connects the Boot button on the target chip and IO9 on the module. Holding
                                   down the Boot button and momentarily pressing the Reset button initiates the
                                   firmware upload mode. Then you can upload firmware through the serial port
                                   or USB.




Espressif Systems                                 105                                              Release master
                                       Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




                          Fig. 8: ESP32-S3-USB-Bridge - Front (Click to Enlarge)




                          Fig. 9: ESP32-S3-USB-Bridge - Back (Click to Enlarge)




Espressif Systems                                106                               Release master
                                      Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




 Key Component                     Description
 5 V to 3.3 V                      Converts the USB voltage to 3.3 V for powering the ESP32-S3-MINI-1 mod-
                                   ule.
 Module Boot Button                Connects IO0 on the module. After holding down the Boot button and power-
                                   ing up the development board again, the board enters the download mode and
                                   initiates the firmware upload mode for uploading firmware.
 WS2812                            Connects IO42 on the module and indicates the current state of the development
                                   board.


Software Support Development of applications for ESP32-S3-USB-Bridge can be done using ESP-IDF frame-
work. ESP-IDF is a FreeRTOS-based SoC development framework with several components including LCD, ADC,
RMT, and SPI. An example is provided for ESP32-S3-LCD-EV-Board under the folder Examples . You can config-
ure project options by entering idf.py menuconfig in the example directory.


Note:
    • The current supported ESP-IDF version is release/5.0.
    • To prevent the default firmware from being replaced, please avoid pressing and holding the module s own
      Boot button while powering the board up/down.



Start Application Development

This section provides instructions on how to do hardware and software setup and flash firmware onto the board to
develop your own application.


Required Hardware
    • 1 x ESP32-S3-USB-Bridge
    • 1 x LCD subboard
    • 1 x USB 2.0 cable (standard Type-A to Type-C)
    • 1 x PC (Windows, Linux, or macOS)


Note: Please make sure to use the appropriate USB cable. Some cables can only be used for charging, not for data
transfer or program flashing.



Hardware Setup Prepare the board for loading of the first sample application:
   1. Plug in the USB cable to connect the PC with the USB port on the board.
   2. Make sure the board is in the download mode.
   3. The LED lights up indicating the completion of flashing.
Now the board is ready for software setup.


Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel-
opment environment.
For more software information on developing applications, please go to Software Support.


Hardware Reference

This section provides more detailed information about the board s hardware.


Espressif Systems                                 107                                              Release master
                                       Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


GPIO Allocation The table below provides the GPIO allocation of the ESP32-S3-MINI-1 module and its 12-pin
expansion connector, which is used to control specific components or functions on the development board as well as
the externally connected target chip.

                     Table 1: ESP32-S3-MINI-1 and Expansion Connector GPIO Allocation
 Pin                      Pin Name                  Function
 1                        GND                       GND
 2                        3V3                       Power supply
 3                        IO0                       Module boot button for entering download mode which can
                                                    also be used as a key input pin
 4                        IO2                       JTAG pin TDO for test data output
 5                        IO3                       JTAG pin TDI for test data input
 6                        IO4                       JTAG pin TCK for synchronized test data transfer
 7                        IO5                       JTAG pin TMS for test mode configuration
 8                        IO8                       The Reset pin connecting to the target chip, which sets the
                                                    target chip to low level when pressed
 9                        IO9                       The Boot pin connecting to the target chip, which sets the tar-
                                                    get chip to low level when pressed
 10                       IO19                      USB_D-
 11                       IO20                      USB_D+
 12                       IO40                      RX connecting to the UART TX pin of the target chip
 13                       IO41                      TX connecting to the UART RX pin of the target chip
 14                       IO42                      WS2812 control pin



Note: Pin 3 to Pin 14 are the corresponding pins of the 12-pin expansion connector. Apart from the features in the
above table, all these IO pins support to be configured for other purposes. Note that GPIO5 and GPIO8 should be
connected to external keys.



Power Distribution


Power Supply over USB There are two ways to power the development board via the USB power port:
     • Via the Type-A port




                             Fig. 10: ESP32-S3-USB-Bridge - Type-A Power Supply

     • Via the Type-C port


Voltage Conversion Circuit The ESP32-S3-USB-Bridge supports converting 5 V to 3.3 V for the module.


Espressif Systems                                 108                                                Release master
                                       Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




                          Fig. 11: ESP32-S3-USB-Bridge - Type-C Power Supply




                           Fig. 12: ESP32-S3-USB-Bridge - Voltage Conversion




Espressif Systems                                109                           Release master
                                      Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards


Hardware Setup Options


Automatic Download Press the Boot button on the module and re-power up the board, then release the Boot button
to allow the board to enter the download mode.


Hardware Revision Details

No previous revisions.


Sample Request

This board has been open-sourced to OSHWHub. Please sample it according to your needs.


Related Documents

Please download the following documents from the HTML version of esp-dev-kits Documentation.
    • ESP32-S3 Datasheet
    • ESP32-S3-MINI-1 Datasheet
    • ESP Product Selector
    • ESP32-S3-USB-Bridge PCB Layout
    • ESP32-S3-USB-Bridge Schematics
For further design documentation for the board, please contact us at sales@espressif.com.




Espressif Systems                                  110                                         Release master
                                        Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




 ESP32-S3 Development Boards




 ESP32-S3-DevKitC-1                                      ESP32-S3-USB-OTG




 ESP32-S3-LCD-EV-Board                                   ESP-VoCat




 ESP-DualKey




Espressif Systems                                111                        Release master
                                      Submit Document Feedback


---

Chapter 6. EOL (End of Life) Boards




Espressif Systems                                112             Release master
                                      Submit Document Feedback


---

Chapter 7

Related Documentation and Resources


7.1   Related Documentation
  • ESP32-S3 Datasheet Specifications of the ESP32-S3 hardware.
  • ESP32-S3 Technical Reference Manual Detailed information on how to use the ESP32-S3 memory and pe-
    ripherals.
  • ESP32-S3 Hardware Design Guidelines Guidelines on how to integrate the ESP32-S3 into your hardware
    product.
  • ESP32-S3 Product/Process Change Notifications (PCN)
    https://espressif.com/en/support/documents/pcns?keys=ESP32-S3
  • ESP32-S3 Advisories Information on security, bugs, compatibility, component reliability.
    https://espressif.com/en/support/documents/advisories?keys=ESP32-S3
  • Certificates
    https://espressif.com/en/support/documents/certificates
  • Documentation Updates and Update Notification Subscription
    https://espressif.com/en/support/download/documents


7.2   Developer Zone
  • ESP-IDF Programming Guide for ESP32-S3 Extensive documentation for the ESP-IDF development frame-
    work.
  • ESP-IoT-Solution Programming Guide - Extensive documentation for the ESP-IoT-Solution development
    framework.
  • ESP-FAQ - A summary document of frequently asked questions released by Espressif.
  • ESP-IDF and other development frameworks on GitHub.
    https://github.com/espressif
  • ESP32 BBS Forum Engineer-to-Engineer (E2E) Community for Espressif products where you can post ques-
    tions, share knowledge, explore ideas, and help solve problems with fellow engineers.
    https://esp32.com/
  • The ESP Journal Best Practices, Articles, and Notes from Espressif folks.
    https://blog.espressif.com/
  • See the tabs SDKs and Demos, Apps, Tools, AT Firmware.
    https://espressif.com/en/support/download/sdks-demos




                                                                                                    113


---

Chapter 7. Related Documentation and Resources


7.3    Products
   • ESP32-S3 Series SoCs Browse through all ESP32-S3 SoCs.
     https://espressif.com/en/products/socs?id=ESP32-S3
   • ESP32-S3 Series Modules Browse through all ESP32-S3-based modules.
     https://espressif.com/en/products/modules?id=ESP32-S3
   • ESP32-S3 Series DevKits Browse through all ESP32-S3-based devkits.
     https://espressif.com/en/products/devkits?id=ESP32-S3
   • ESP Product Selector Find an Espressif hardware product suitable for your needs by comparing or applying
     filters.
     https://products.espressif.com/#/product-selector


7.4    Contact Us
   • See the tabs Sales Questions, Technical Enquiries, Circuit Schematic & PCB Design Review, Get Samples
     (Online stores), Become Our Supplier, Comments & Suggestions.
     https://espressif.com/en/contact-us/sales-questions




Espressif Systems                               114                                           Release master
                                     Submit Document Feedback


---

Chapter 8

Disclaimer and Copyright Notice


Information in this document, including URL references, is subject to change without notice.
All third party s information in this document is provided as is with no warranties to its authenticity and accuracy.
No warranty is provided to this document for its merchantability, non-infringement, fitness for any particular purpose,
nor does any warranty otherwise arising out of any proposal, specification or sample.
All liability, including liability for infringement of any proprietary rights, relating to use of information in this doc-
ument is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are
granted herein.
The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is a registered trademark
of Bluetooth SIG.
All trade names, trademarks and registered trademarks mentioned in this document are property of their respective
owners, and are hereby acknowledged.




                                                                                                                     115


---