Datasheet docs

{ "mpn": "ADS7029" }

ADS7029

Small-Size, Low-Power, 8-Bit, 2-MSPS, SAR ADC

Input

ADS7029-Q1 Small-Size, Low-Power, 8-Bit, 2-MSPS, SAR ADC

1 Features

1• Qualified for Automotive Applications

• AEC-Q100 Qualified With the Following Results:

Device Temperature Grade $1 : - 4 0 ^ { \circ } \mathsf { C }$ to $1 2 5 ^ { \circ } \mathrm { C }$ Ambient Operating Temperature Range

– Device HBM ESD Classification Level ±2000 V

– Device CDM ESD Classification Level ±1000 V

• Ultra-Low Power Consumption:

– 1.11 mW (max) at 2 MSPS with 3-V AVDD

– Less Than 1 µW at 1 kSPS with 3-V AVDD

• Miniature Footprint:

– 8-Pin VSSOP Package: 2.30 mm × 2.00 mm

• 2-MSPS Throughput with Zero Data Latency

• Wide Operating Range:

– AVDD: 2.35 V to 3.6 V

– DVDD: 1.65 V to 3.6 V (Independent of AVDD)

– Temperature Range: $\scriptscriptstyle - 4 0 ^ { \circ } \mathsf { C }$ to $+ 1 2 5 ^ { \circ } \mathrm { C }$

• Excellent Performance:

– 8-Bit Resolution with NMC

– ±0.2 LSB DNL; ±0.25 LSB INL

– 49-dB SNR with 3-V AVDD

– –70-dB THD with 3-V AVDD

• Unipolar Input Range: 0 V to AVDD

• Integrated Offset Calibration

• SPI-Compatible Serial Interface: 32 MHz

• JESD8-7A Compliant Digital I/O

2 Applications

• Automotive Infotainment

• Automotive Sensors

• Level Sensors

• Ultrasonic Flow Meters

• Motor Control

• Portable Medical Equipment

3 Description

The ADS7029-Q1 device is a an automotive Q100- qualified, 8-bit, 2-MSPS, analog-to-digital converter (ADC). The device supports a wide analog input voltage range (2.35 V to 3.6 V) and includes a capacitor-based, successive-approximation register (SAR) ADC with an inherent sample-and-hold circuit. The SPI-compatible serial interface is controlled by the CS and SCLK signals. The input signal is sampled with the CS falling edge and SCLK is used for conversion and serial data output. The device supports a wide digital supply range (1.65 V to 3.6 V), enabling direct interface to a variety of host controllers. The ADS7029-Q1 complies with the JESD8-7A standard for a normal DVDD range (1.65 V to 1.95 V).

The ADS7029-Q1 is available in an 8-pin, miniature, VSSOP package and is specified for operation from –40°C to +125°C. The fast sampling rate of the ADS7029-Q1, along with miniature form-factor and low-power consumption, makes this device suitable for space-constrained and fast-scanning automotive applications.

Device Information(1)

PART NAMEPACKAGEBODY SIZE (NOM)
ADS7029-Q1VSSOP (8)2.30 mm × 2.00 mm

(1) For all available packages, see the orderable addendum at the end of the datasheet.

Typical Application

Copyright © 2016, Texas Instruments Incorporated

Table of Contents

1 Features.... 1
2 Applications.... 1
3 Description.... 1
4 Revision History.... 2
5 Pin Configuration and Functions.... 3
6 Specifications.... 4
6.1 Absolute Maximum Ratings.... 4
6.2 ESD Ratings.... 4
6.3 Recommended Operating Conditions.... 4
6.4 Thermal Information.... 4
6.5 Electrical Characteristics.... 5
6.6 Timing Requirements.... 6
6.7 Switching Characteristics.... 6
6.8 Typical Characteristics.... 7
7 Parameter Measurement Information.... 12
7.1 Digital Voltage Levels.... 12
8 Detailed Description.... 12
8.1 Overview.... 12
8.2 Functional Block Diagram.... 13
8.3 Feature Description.... 13

8.4 Device Functional Modes.... 17
9 Application and Implementation.... 20
9.1 Application Information.... 20
9.2 Typical Application.... 20
10 Power Supply Recommendations.... 23
10.1 AVDD and DVDD Supply Recommendations.... 23
10.2 Estimating Digital Power Consumption.... 23
10.3 Optimizing Power Consumed by the Device.... 23
11 Layout.... 24
11.1 Layout Guidelines.... 24
11.2 Layout Example.... 24
12 Device and Documentation Support.... 25
12.1 Documentation Support.... 25
12.2 Receiving Notification of Documentation Updates.... 25
12.3 Community Resources.... 25
12.4 Trademarks.... 25
12.5 Electrostatic Discharge Caution.... 25
12.6 Glossary.... 25
13 Mechanical, Packaging, and Orderable Information.... 25

4 Revision History

DATEREVISIONNOTES
January 2017*Initial release.

5 Pin Configuration and Functions

Pin Functions

NAMENO.I/ODESCRIPTION
AINM5Analog inputAnalog signal input, negative
AINP6Analog inputAnalog signal input, positive
AVDD7SupplyAnalog power-supply input, also provides the reference voltage to the ADC
$\overline{CS}$ 4Digital inputChip-select signal, active low
DVDD1SupplyDigital I/O supply voltage
GND8SupplyGround for power supply, all analog and digital signals are referred to this pin
SCLK2Digital inputSerial clock
SDO3Digital outputSerial data out

6 Specifications

6.1 Absolute Maximum Ratings(1)

MINMAXUNIT
AVDD to GND-0.33.9V
DVDD to GND-0.33.9V
AINP to GND-0.3AVDD + 0.3V
AINM to GND-0.30.3V
Digital input voltage to GND-0.3DVDD + 0.3V
Storage temperature, $T_{stg}$ -60150°C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

6.2 ESD Ratings

VALUEUNIT
$V_{(ESD)}$ Electrostatic dischargeHuman-body model (HBM), per AEC Q100-002 $^{(1)}$ ±2000V
Charged-device model (CDM), per AEC Q100-011±1000

(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)

MINNOMMAXUNIT
AVDDAnalog supply voltage range2.353.6V
DVDDDigital supply voltage range1.653.6V
$T_A$ Operating free-air temperature-40125°C

6.4 Thermal Information

THERMAL METRIC(1)ADS7029-Q1UNIT
DCU (VSSOP)
8 PINS
$R_{\theta JA}$ Junction-to-ambient thermal resistance181.8°C/W
$R_{\theta JC(top)}$ Junction-to-case (top) thermal resistance50.8°C/W
$R_{\theta JB}$ Junction-to-board thermal resistance73.9°C/W
$\psi_{JT}$ Junction-to-top characterization parameter1.0°C/W
$\psi_{JB}$ Junction-to-board characterization parameter73.9°C/W
$R_{\theta JC(bot)}$ Junction-to-case (bottom) thermal resistanceN/A°C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.

6.5 Electrical Characteristics

PARAMETERTEST CONDITIONSMINTYPMAXUNIT
ANALOG INPUT
Full-scale input voltage span(1)0AVDDV
Absolute input voltage rangeAINP to GND-0.1AVDD + 0.1V
AINM to GND-0.10.1
$C_S$ Sampling capacitance15pF
SYSTEM PERFORMANCE
Resolution8Bits
NMC No missing codes8Bits
INL Integral nonlinearityAVDD = 3 V-0.5±0.250.5LSB(2)
DNL Differential nonlinearityAVDD = 3 V-0.4±0.20.4LSB
$E_O$ Offset error±0.5LSB
d $V_{OS}$ /dT Offset error drift with temperature±25ppm/°C
$E_G$ Gain errorAVDD = 3 V±0.2%FS
Gain error drift with temperatureNo calibration±25ppm/°C
SAMPLING DYNAMICS
$t_{ACQ}$ Acquisition time120ns
Maximum throughput rate32-MHz SCLK, AVDD = 2.35 V to 3.6 V2MHz
DYNAMIC CHARACTERISTICS
SNR Signal-to-noise ratio(3) $f_{IN}$ =2 kHz, AVDD=3 V48.549dB
THD Total harmonic distortion(3)(4) $f_{IN}$ =2 kHz, AVDD=3 V-70dB
SINAD Signal-to-noise and distortion(3) $f_{IN}$ =2 kHz, AVDD=3 V48.549dB
SFDR Spurious-free dynamic range(3) $f_{IN}$ =2 kHz, AVDD=3 V75dB
$BW_{(fp)}$ Full-power bandwidthAt -3 dB, AVDD=3 V25MHz
DIGITAL INPUT/OUTPUT (CMOS Logic Family)
$V_{IH}$ High-level input voltage(5)0.65 × DVDDDVDD + 0.3V
$V_{IL}$ Low-level input voltage(5)-0.30.35 × DVDDV
$V_{OH}$ High-level output voltage(5)At $I_{source}$ =500 μA0.8 × DVDDDVDDV
At $I_{source}$ =2 mADVDD - 0.45DVDD
$V_{OL}$ Low-level output voltage(5)At $I_{sink}$ =500 μA00.2 × DVDDV
At $I_{sink}$ =2 mA00.45
POWER-SUPPLY REQUIREMENTS
AVDD Analog supply voltage2.3533.6V
DVDD Digital I/O supply voltage1.6533.6V
$I_{AVDD}$ Analog supply currentAt 2 MSPS with AVDD = 3 V335370μA
$I_{DVDD}$ Digital supply currentAVDD = 3 V, no load, no transitions10μA
$P_D$ Power dissipationAt 2 MSPS with AVDD = 3 V1.0051.11mW

(1) Ideal input span; does not include gain or offset error.
(2) LSB means least significant bit.
(3) All specifications expressed in decibels (dB) refer to the full-scale input (FSR) and are tested with an input signal 0.5 dB below full-scale, unless otherwise specified.
(4) Calculated on the first nine harmonics of the input frequency.
(5) Digital voltage levels comply with the JESD8-7A standard for DVDD from 1.65 V to 1.95 V; see the Digital Voltage Levels section for more details.

6.6 Timing Requirements

all specifications are at $\mathsf { T } _ { \mathsf { A } } = - 4 0 ^ { \circ } \mathsf { C }$ to ${ 1 2 5 ^ { \circ } \mathrm { C } } ,$ AVDD = 2.35 V to 3.6 V, DVDD = 1.65 V to 3.6 V, and $\mathsf { C } _ { \mathsf { L O A D } }$ on SDO = 20 pF (unless otherwise specified)

MINTYPMAXUNIT
$t_{ACQ}$ Acquisition time120ns
$f_{SCLK}$ SCLK frequency0.01624MHz
$t_{SCLK}$ SCLK period41.67ns
$t_{PH\_CK}$ SCLK high time0.450.55 $t_{SCLK}$
$t_{PL\_CK}$ SCLK low time0.450.55 $t_{SCLK}$
$t_{PH\_CS}$ $\overline{CS}$ high time30ns
$t_{SU\_CSCK}$ Setup time: $\overline{CS}$ falling to SCLK falling12ns
$t_{D\_CKCS}$ Delay time: last SCLK falling to $\overline{CS}$ rising10ns

6.7 Switching Characteristics

all specifications are at $\mathsf { T } _ { \mathsf { A } } = - 4 0 ^ { \circ } \mathsf { C }$ to ${ 1 2 5 ^ { \circ } \mathsf C } ,$ AVDD = 2.35 V to 3.6 V, DVDD = 1.65 V to 3.6 V, and $\mathsf { C } _ { \mathsf { L O A D } }$ on SDO = 20 pF (unless otherwise specified)

PARAMETERTEST CONDITIONSMINTYPMAXUNIT
$f_{THROUGHPUT}$ Throughput2MSPS
$t_{CYCLE}$ Cycle time0.5μs
$t_{CONV}$ Conversion time8.5 × $t_{SCLK} + t_{SU\_CSCK}$ ns
$t_{DV\_CSDO}$ Delay time: $\overline{CS}$ falling to data enable10ns
$t_{D\_CKDO}$ Delay time: SCLK falling to (next) data valid on DOUTAVDD = 2.35 V to 3.6 V25ns
$t_{DZ\_CSDO}$ Delay time: $\overline{CS}$ rising to DOUT going to tri-state5ns


Figure 1. Timing Diagram

6.8 Typical Characteristics

at ${ \sf T } _ { \sf A } = 2 5 ^ { \circ } { \sf C }$ , AVDD = 3 V, $\mathsf { D V D D } = 1 . 8 \mathsf { V } ,$ and $\mathsf { f } _ { \mathsf { S A M P L E } } = 2$ MSPS (unless otherwise noted)


SNR = 49.65 dB, THD = –73.26 dB, f = 2 kHz, AVDD = 3 V

Figure 2. Typical FFT

SNR = 49.19 dB, THD = –71.25 dB, f = 250 kHz, AVDD = 3 V

Figure 3. Typical FFT

Figure 4. SNR and SINAD vs Temperature

Figure 6. SNR and SINAD vs Reference Voltage (AVDD)
Figure 5. SNR and SINAD vs Input Frequency

Figure 7. THD vs Temperature

Typical Characteristics (continued)

at ${ \sf T } _ { \sf A } = 2 5 ^ { \circ } { \sf C }$ , AVDD = 3 V, DVDD = 1.8 V, and $\mathbf { f } _ { \mathsf { S A M P L E } } = 2$ MSPS (unless otherwise noted)

Figure 8. SFDR vs Temperature

Figure 9. THD vs Input Frequency

Figure 10. SFDR vs Input Frequency

Figure 12. SFDR vs Reference Voltage (AVDD)

Figure 11. THD vs Reference Voltage (AVDD)

Figure 13. DC Input Histogram

Typical Characteristics (continued)

at ${ \sf T } _ { \sf A } = 2 5 ^ { \circ } { \sf C }$ , AVDD = 3 V, DVDD = 1.8 V, and $\mathsf { f } _ { \mathsf { S A M P L E } } = 2$ MSPS (unless otherwise noted)

Figure 14. Typical DNL

Figure 15. Typical INL

Figure 16. Typical DNL

Figure 18. DNL vs Temperature

Figure 17. Typical INL

Figure 19. DNL vs Reference Voltage (AVDD)

Typical Characteristics (continued)

at ${ \sf T } _ { \sf A } = 2 5 ^ { \circ } { \sf C }$ , AVDD = 3 V, DVDD = 1.8 V, and $\mathbf { f } _ { \mathsf { S A M P L E } } = 2$ MSPS (unless otherwise noted)

Figure 20. INL vs Temperature

Figure 21. INL vs Reference Voltage (AVDD)

Figure 22. AVDD Supply Current vs Temperature

Figure 24. AVDD Supply Current vs Supply Voltage

Figure 23. AVDD Supply Current vs Throughput

Figure 25. ENOB vs Sampling Rate

www.ti.com

Typical Characteristics (continued)
at $\bar { \mathsf { T } } _ { \mathsf { A } } = 2 5 ^ { \circ } \mathsf { C }$ , AVDD = 3 V, DVDD = 1.8 V, and $\mathbf { f } _ { \mathsf { S A M P L E } } = 2$ MSPS (unless otherwise noted)

Figure 26. SNR vs Sampling Rate

Figure 27. SINAD vs Sampling Rate

Figure 28. THD vs Sampling Rate

7 Parameter Measurement Information

7.1 Digital Voltage Levels

The device complies with the JESD8-7A standard for DVDD from 1.65 V to 1.95 V. Figure 29 shows voltage levels for the digital input and output pins.


Figure 29. Digital Voltage Levels as per the JESD8-7A Standard

8 Detailed Description

8.1 Overview

The ADS7029-Q1 is an ultra-low-power, miniature analog-to-digital converter (ADC) that supports a wide analog input range. The analog input range for the device is defined by the AVDD supply voltage. The device samples the input voltage across the AINP and AINM pins on the CS falling edge and starts the conversion. The clock provided on the SCLK pin is used for conversion and data transfer. During conversions, both the AINP and AINM pins are disconnected from the sampling circuit. After the conversion completes, the sampling capacitors are reconnected across the AINP and AINM pins and the ADS7029-Q1 enters acquisition phase.

The device has an internal offset calibration. The offset calibration can be initiated by the user either on power-up or during normal operation; see the Offset Calibration section for more details.

The device also provides a simple serial interface to the host controller and operates over a wide range of digital power supplies. The ADS7029-Q1 requires only a 24-MHz SCLK for supporting a throughput of 2 MSPS. The digital interface also complies with the JESD8-7A (normal range) standard. The Functional Block Diagram section provides a block diagram of the device.

8.2 Functional Block Diagram

8.3 Feature Description

8.3.1 Reference

The device uses the analog supply voltage (AVDD) as a reference, as shown in Figure 30. The AVDD pin is recommended to be decoupled with a 3.3-µF, low equivalent series resistance (ESR) ceramic capacitor.. The AVDD pin functions as a switched capacitor load to the source powering AVDD. The decoupling capacitor provides the instantaneous charge required by the internal circuit and helps in maintaining a stable dc voltage on the AVDD pin. The AVDD pin is recommended to be powered with a low output impedance and low-noise regulator (such as the TPS73230).


Figure 30. Reference for the Device

Feature Description (continued)

8.3.2 Analog Input

The device supports single-ended analog inputs. The ADC samples the difference between AINP and AINM and converts for this voltage. The device is capable of accepting a signal from –100 mV to 100 mV on the AINM input and is useful in systems where the sensor or signal-conditioning block is far from the ADC. In such a scenario, there can be a difference between the ground potential of the sensor or signal conditioner and the ADC ground. In such cases, use separate wires to connect the ground of the sensor or signal conditioner to the AINM pin. The AINP input is capable of accepting signals from 0 V to AVDD. Figure 31 represents the equivalent analog input circuits for the sampling stage. The device has a low-pass filter followed by the sampling switch and sampling capacitor. The sampling switch is represented by an $\mathsf { R } _ { \mathsf { S } }$ (typically 50 Ω) resistor in series with an ideal switch and ${ \sf C } _ { \sf S }$ (typically 15 pF) is the sampling capacitor. The ESD diodes are connected from both analog inputs to AVDD and ground.


Figure 31. Equivalent Input Circuit for the Sampling Stage

The analog input full-scale range (FSR) is equal to the reference voltage of the ADC. The reference voltage for the device is equal to the analog supply voltage (AVDD). Thus, the device FSR can be determined by Equation 1:

$$
\mathrm{FSR} = \mathrm{V} _ {\mathrm{REF}} = \mathrm{AVDD}\tag{1}
$$

Feature Description (continued)

8.3.3 ADC Transfer Function

The device output is in straight binary format. The device resolution for a single-ended input can be computed by Equation 2:

$$
1 \mathrm{LSB} = V _ {\mathrm{REF}} / 2 ^ {N}
$$

where:

$\mathsf { V } _ { \mathsf { R E F } } = \mathsf { A V D D a n d }$

$\Nu = 8$

(2)

Figure 32 and Table 1 show the ideal transfer characteristics for the device.


Figure 32. Ideal Transfer Characteristics

Table 1. Transfer Characteristics

INPUT VOLTAGE (AINP – AINM)CODEDESCRIPTIONIDEAL OUTPUT CODE (HEX)
≤1 LSBNFSCNegative full-scale code00
1 LSB to 2 LSBsNFSC + 1—01
$(V_{REF} / 2)$ to $(V_{REF} / 2) + 1$ LSBMCMid code80
$(V_{REF} / 2) + 1$ LSB to $(V_{REF} / 2) + 2$ LSBsMC + 1—81
≥ $V_{REF} - 1$ LSBPFSCPositive full-scale codeFF

8.3.4 Serial Interface

The device supports a simple, SPI-compatible interface to the external host. The $\overline { { \mathsf { C S } } }$ signal defines one conversion and serial transfer frame. A frame starts with a CS falling edge and ends with a CS rising edge. The SDO pin outputs the ADC conversion results. Figure 33 shows a detailed timing diagram for the serial interface. A minimum delay of $\mathfrak { t } _ { \mathtt { S U } _ { \mathtt { - } } }$ _CSCK must elapse between the CS falling edge and the first SCLK falling edge. The device uses the clock provided on the SCLK pin for conversion and data transfer. The conversion result is available on the SDO pin with the first two bits set to 0, followed by 12 bits of the conversion result. The first zero is launched on the SDO pin on the CS falling edge. Subsequent bits (starting with another 0 followed by the conversion result) are launched on the SDO pin on subsequent SCLK falling edges. The SDO output remains low after 14 SCLKs. A CS rising edge ends the frame and brings the serial data bus to tri-state. For acquisition of the next sample, a minimum time of $\mathtt { t _ { A C Q } }$ must be provided after the conversion of the current sample is completed. For details on timing specifications, see the Timing Requirements table.

The device initiates an offset calibration on the first $\overline { { \mathsf { C S } } }$ falling edge after power-up and the SDO output remains low during the first serial transfer frame after power-up. For further details, see the Offset Calibration section.


Figure 33. Serial Interface Timing Diagram

www.ti.com

8.4 Device Functional Modes

8.4.1 Offset Calibration

The ADS7029-Q1 includes a feature to calibrate the device internal offset. During offset calibration, the analog input pins (AINP and AINM) are disconnected from the sampling stage. The device includes an internal offset calibration register (OCR) that stores the offset calibration result. The OCR is an internal register and cannot be accessed by the user through the serial interface. The OCR is reset to zero on power-up. Therefore, it is recommended to calibrate the offset on power-up in order to bring the offset error within the specified limits. If the operating temperature or analog supply voltage reflect a significant change, the offset can be recalibrated during normal operation. Figure 34 shows the offset calibration process.

(1) See the Timing Requirements section for timing specifications.

(2) See the Offset Calibration During Normal Operation section for details.

(3) See the Offset Calibration on Power-Up section for details.

(4) The power recycle on the AVDD supply is required to reset the offset calibration and to bring the device to a power-up state.

Figure 34. Offset Calibration

Device Functional Modes (continued)

8.4.1.1 Offset Calibration on Power-Up

The device initiates offset calibration on the first CS falling edge after power-up and calibration completes if the CS pin remains low for at least 16 SCLK falling edges after the first CS falling edge. The SDO output remains low during calibration. The minimum acquisition time must be provided after calibration for acquiring the first sample. If the device is not provided with at least 16 SCLKs during the first serial transfer frame after power-up, the OCR is not updated. Table 2 provides the timing parameters for offset calibration on power-up.

For subsequent samples, the device adjusts the conversion results with the value stored in the OCR. The conversion result adjusted with the value stored in OCR is provided by the device on the SDO output. Figure 35 shows the timing diagram for offset calibration on power-up.

Table 2. Offset Calibration on Power-Up

MINTYPMAXUNIT
$f_{CLK-CAL}$ SCLK frequency for calibration12MHz
$t_{POWERUP-CAL}$ Calibration time at power-up $15 \times t_{SCLK}$ ns
$t_{ACQ}$ Acquisition time120ns
$t_{PH\_CS}$ $\overline{CS}$ high time $t_{ACQ}$ ns
$t_{SU\_CSCK}$ Setup time: $\overline{CS}$ falling to SCLK falling12ns
$t_{D\_CKCS}$ Delay time: last SCLK falling to $\overline{CS}$ rising10ns


Figure 35. Offset Calibration on Power-Up Timing Diagram

www.ti.com

8.4.1.2 Offset Calibration During Normal Operation

Offset calibration can be done during normal device operation if at least 32 SCLK falling edges are provided in one serial transfer frame. During the first 10 SCLKs, the device converts the sample acquired on the CS falling edge and provides data on the SDO output. The device initiates the offset calibration on the 17th SCLK falling edge and calibration completes on the 32nd SCLK falling edge. The SDO output remains low after the 10th SCLK falling edge and SDO goes to tri-state after CS goes high. If the device is provided with less than 32 SCLKs during a serial transfer frame, the OCR is not updated. Table 3 provides the timing parameters for offset calibration during normal operation.

For subsequent samples, the device adjusts the conversion results with the value stored in the OCR. The conversion result adjusted with the value stored in the OCR is provided by the device on the SDO output. Figure 36 shows the timing diagram for offset calibration during normal operation.

Table 3. Offset Calibration During Normal Operation

MINTYPMAXUNIT
$f_{CLK-CAL}$ SCLK frequency for calibration12MHz
$t_{CAL}$ Calibration time during normal operation $15 \times t_{SCLK}$ ns
$t_{ACQ}$ Acquisition time120ns
$t_{PH\_CS}$ $\overline{CS}$ high time $t_{ACQ}$ ns
$t_{SU\_CSCK}$ Setup time: $\overline{CS}$ falling to SCLK falling12ns
$t_{D\_CKCS}$ Delay time: last SCLK falling to $\overline{CS}$ rising10ns


Figure 36. Offset Calibration During Normal Operation Timing Diagram

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality.

9.1 Application Information

The two primary circuits required to maximize the performance of a SAR ADC are the input driver and the reference driver circuits. This section details some general principles for designing the input driver circuit, reference driver circuit, and provides some application circuits designed for the ADS7029-Q1.

9.2 Typical Application


Figure 37. Single-Supply DAQ with the ADS7029-Q1

9.2.1 Design Requirements

The goal of this application is to design a single-supply digital acquisition (DAQ) circuit based on the ADS7029- Q1 with SNR greater than 49 dB and THD less than –70 dB for input frequencies of 2 kHz at a throughput of 2 MSPS.

9.2.2 Detailed Design Procedure

The input driver circuit for a high-precision ADC mainly consists of two parts: a driving amplifier and a charge kickback filter. Careful design of the front-end circuit is critical to meet the linearity and noise performance of a high-precision ADC.

Typical Application (continued)

9.2.2.1 Low Distortion Charge Kickback Filter Design

Figure 38 shows the input circuit of a typical SAR ADC. During the acquisition phase, the SW switch closes and connects the sampling capacitor $( \mathsf { C } _ { \mathsf { S H } } )$ to the input driver circuit. This action introduces a transient on the input pins of the SAR ADC. An ideal amplifier with 0 Ω of output impedance and infinite current drive can settle this transient in zero time. For a real amplifier with non-zero output impedance and finite drive strength, this switched capacitor load can create stability issues.


Figure 38. Charge Kickback Filter

For ac signals, the filter bandwidth must be kept low to band limit the noise fed into the ADC input, thereby increasing the SNR of the system. Besides filtering the noise from the front-end drive circuitry, the RC filter also helps attenuate the sampling charge injection from the switched-capacitor input stage of the ADC. A filter capacitor, $\complement _ { \mathsf { F L T } }$ , is connected across the ADC inputs. This capacitor helps reduce the sampling charge injection and provides a charge bucket to quickly charge the internal sample-and-hold capacitors during the acquisition process. As a rule of thumb, the value of this capacitor is at least 20 times the specified value of the ADC sampling capacitance. For this device, the input sampling capacitance is equal to 15 pF. Thus, the value of $\complement _ { \mathsf { F L T } }$ is greater than 300 pF. Select a COG- or NPO-type capacitor because these capacitor types have a high-Q, low temperature coefficient, and stable electrical characteristics under varying voltages, frequency, and time.

Note that driving capacitive loads can degrade the phase margin of the input amplifiers, thus making the amplifier marginally unstable. To avoid amplifier stability issues, series isolation resistors $( \mathsf { R } _ { \mathsf { F L T } } )$ are used at the output of the amplifiers. A higher value of $\dot { \mathsf { R } } _ { \mathsf { F L T } }$ is helpful from the amplifier stability perspective, but adds distortion as a result of interactions with the nonlinear input impedance of the ADC. Distortion increases with source impedance, input signal frequency, and input signal amplitude. Therefore, the selection of $\mathsf { R } _ { \mathsf { F L T } }$ requires balancing the stability and distortion of the design.

The input amplifier bandwidth is typically much higher than the cutoff frequency of the antialiasing filter. Thus, a SPICE simulation is strongly recommended to be performed to confirm that the amplifier has more than $4 0 ^ { \circ }$ phase margin with the selected filter. Simulation is critical because even with high-bandwidth amplifiers, some amplifiers can require more bandwidth than others to drive similar filters.

Typical Application (continued)

9.2.2.2 Input Amplifier Selection

To achieve a SINAD greater than 49 dB, the operational amplifier must have high bandwidth in order to settle the input signal within the acquisition time of the ADC. The operational amplifier must have low noise to keep the total system noise below 20% of the input-referred noise of the ADC. For the application circuit illustrated in Figure 37, the OPA365-Q1 is selected for its high bandwidth (50 MHz) and low noise (4.5 nV/√Hz).

For a step-by-step design procedure for a low-power, small form-factor digital acquisition (DAQ) circuit based on similar SAR ADCs, see the Three 12-Bit Data Acquisition Reference Designs Optimized for Low Power and Ultra-Small Form Factor TI Precision Design.

9.2.2.3 Reference Circuit

The analog supply voltage of the device is also used as a voltage reference for conversion. The AVDD pin is recommended to be decoupled with a 3.3-µF, low-ESR ceramic capacitor.

9.2.3 Application Curve

Figure 39 shows the FFT plot for the ADS7029-Q1 with a 2-kHz input frequency used for the circuit in Figure 37.


SNR = 70.6 dB, THD = –86 dB, SINAD = 70.2 dB, number of samples = 32768
Figure 39. Test Results for the ADS7029-Q1 and OPA365-Q1 for a 2-kHz Input

10 Power Supply Recommendations

10.1 AVDD and DVDD Supply Recommendations

The ADS7029-Q1 has two separate power supplies: AVDD and DVDD. The device operates on AVDD; DVDD is used for the interface circuits. AVDD and DVDD can be independently set to any value within the permissible ranges. The AVDD supply also defines the full-scale input range of the device. Always set the AVDD supply to be greater than or equal to the maximum input signal to avoid saturation of codes. Decouple the AVDD and DVDD pins individually with 3.3-µF ceramic decoupling capacitors, as shown in Figure 40.


Figure 40. Power-Supply Decoupling

10.2 Estimating Digital Power Consumption

The current consumption from the DVDD supply depends on the DVDD voltage, load capacitance on the SDO line, and the output code. The load capacitance on the SDO line is charged by the current from the SDO pin on every rising edge of the data output and is discharged on every falling edge of the data output. The current consumed by the device from the DVDD supply can be calculated by Equation 3:

$$
I _ {D V D D} = C \times V \times f
$$

where:

• C = Load capacitance on the SDO line

• V = DVDD supply voltage and

• f = Number of transitions on the SDO output

(3)

The number of transitions on the SDO output depends on the output code, and thus changes with the analog input. The maximum value of f occurs when data output on SDO change at every SCLK. SDO data changing at every SCLK results in an output code of AAh or 55h. For an output code of AAh or 55h at a 2-MSPS throughput, the frequency of transitions on the SDO output is 8 MHz.

For the current consumption to remain at the lowest possible value, keep the DVDD supply at the lowest permissible value and keep the capacitance on the SDO line as low as possible.

10.3 Optimizing Power Consumed by the Device

• Keep the analog supply voltage (AVDD) as close as possible to the analog input voltage. Set AVDD to be greater than or equal to the analog input voltage of the device.

• Keep the digital supply voltage (DVDD) at the lowest permissible value.

• Reduce the load capacitance on the SDO output.

• Run the device at the optimum throughput. Power consumption reduces with throughput.

11 Layout

11.1 Layout Guidelines

Figure 41 shows a board layout example for the ADS7029-Q1.

Some of the key considerations for an optimum layout with this device are:

• Use a ground plane underneath the device and partition the printed circuit board (PCB) into analog and digital sections.

• Avoid crossing digital lines with the analog signal path and keep the analog input signals and the reference input signals away from noise sources.

• The power sources to the device must be clean and well-bypassed. Use 2.2-μF ceramic bypass capacitors in close proximity to the analog (AVDD) and digital (DVDD) power-supply pins.

• Avoid placing vias between the AVDD and DVDD pins and the bypass capacitors.

• Connect ground pins to the ground plane using short, low-impedance path.

• Place the fly-wheel RC filters components close to the device.

Among ceramic surface-mount capacitors, COG (NPO) ceramic capacitors provide the best capacitance precision. The type of dielectric used in COG (NPO) ceramic capacitors provides the most stable electrical properties over voltage, frequency, and temperature changes.

11.2 Layout Example


Copyright © 2016, Texas Instruments Incorporated

Figure 41. Example Layout

12 Device and Documentation Support

12.1 Documentation Support

12.1.1 Related Documentation

For related documentation see the following:

• TPS732xx Capacitor-Free, NMOS, 250-mA Low-Dropout Regulator With Reverse Current Protection

Three 12-Bit Data Acquisition Reference Designs Optimized for Low Power and Ultra-Small Form Factor TI Precision Design

• OPAx314 3-MHz, Low-Power, Low-Noise, RRIO, 1.8-V CMOS Operational Amplifier

• OPAx365-Q1 50-MHz Low-Distortion High-CMRR Rail-to-Rail I/O, Single-Supply Operational Amplifiers

12.2 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document.

12.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support.

12.4 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.5 Electrostatic Discharge Caution

This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.

ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

12.6 Glossary

SLYZ022 — TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical packaging and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGING INFORMATION

Orderable part numberStatus(1)Material type(2)Package | PinsPackage qty | CarrierRoHS(3)Lead finish/ Ball material(4)MSL rating/ Peak reflow(5)Op temp (°C)Part marking(6)
ADS7029QDCURQ1ActiveProductionVSSOP (DCU) | 83000 | LARGE T&RYesNIPDAULevel-2-260C-1 YEAR-40 to 12517TT
ADS7029QDCURQ1.AActiveProductionVSSOP (DCU) | 83000 | LARGE T&RYesNIPDAULevel-2-260C-1 YEAR-40 to 12517TT

(1) Status: For more details on status, see our product life cycle.

(2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind.

(3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition.

(4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width.

(5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board.

(6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part.

Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representativ and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS number and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

A0Dimension designed to accommodate the component width
B0Dimension designed to accommodate the component length
K0Dimension designed to accommodate the component thickness
WOverall width of the carrier tape
P1Pitch between successive cavity centers
  • Reel Width (W1)
    QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE

*All dimensions are nomina

DevicePackage TypePackage DrawingPinsSPQReel Diameter (mm)Reel Width W1 (mm)A0 (mm)B0 (mm)K0 (mm)P1 (mm)W (mm)Pin1 Quadrant
ADS7029QDCURQ1VSSOPDCU83000180.08.42.253.351.054.08.0Q3

*All dimensions are nomina

DevicePackage TypePackage DrawingPinsSPQLength (mm)Width (mm)Height (mm)
ADS7029QDCURQ1VSSOPDCU83000223.0270.035.0

SMALL OUTLINE PACKAGE

4225266/A 09/2014

NOTES:


NOTES: (continued)

  1. Publication IPC-7351 may have alternate designs.

  2. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

(R0.05) TYP

SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE: 25X

4225266/A 09/2014

NOTES: (continued)

  1. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations.

  2. Board assembly site may have different recommendations for stencil design.

Extracted Images

Figures and diagrams from the PDF

Preview the extracted datasheet assets and open any image in a separate tab for closer inspection.

ca1361d5cc94d2f77b42145fd7c7b29983aee6084ce5ccec96040b3cb7bfb369.jpg

ca1361d5cc94d2f77b42145fd7c7b29983aee6084ce5ccec96040b3cb7bfb369.jpg

299b2bc8c03e934a44095759373a52b63a8ce62a0a489d4046abfaf3d50b6114.jpg

299b2bc8c03e934a44095759373a52b63a8ce62a0a489d4046abfaf3d50b6114.jpg

b836649e3d33734a23efda42246051389005a3461ee246ff5e8cc49ce71451f5.jpg

b836649e3d33734a23efda42246051389005a3461ee246ff5e8cc49ce71451f5.jpg

e106a38f70975b2d168b8054ff5c4b62953033d17d0a7bf1b9947c636c288c74.jpg

e106a38f70975b2d168b8054ff5c4b62953033d17d0a7bf1b9947c636c288c74.jpg

b79244ec3c32c502697f66d6685db79e0c5d32af3361cc2c25b20330b2333cfb.jpg

b79244ec3c32c502697f66d6685db79e0c5d32af3361cc2c25b20330b2333cfb.jpg

2cea58238925a9783544a31eee9ee57a5f190dbd9e2aede70e406623ce938f14.jpg

2cea58238925a9783544a31eee9ee57a5f190dbd9e2aede70e406623ce938f14.jpg

a12545591362ede32d380bd17b22ba535a396f651e9d3e3425ac6283fa7876b8.jpg

a12545591362ede32d380bd17b22ba535a396f651e9d3e3425ac6283fa7876b8.jpg

8185a73f51b1479860aa9e4f2be764bd1862683df67799679cb1010873c21fae.jpg

8185a73f51b1479860aa9e4f2be764bd1862683df67799679cb1010873c21fae.jpg

cacc95d249e72d90e8be35d8a4697edbe516a29c4f344594c70a1b7fe9fd0a1c.jpg

cacc95d249e72d90e8be35d8a4697edbe516a29c4f344594c70a1b7fe9fd0a1c.jpg

f7d5a4bee5a5a32d2c8dddb47200f9fb4356b28fcbbdfb26fc4daf314dc8b88d.jpg

f7d5a4bee5a5a32d2c8dddb47200f9fb4356b28fcbbdfb26fc4daf314dc8b88d.jpg

80534fb3bb712c6a83fbe7a5b03d66cf94030792ba553b6983771c24911e6a4f.jpg

80534fb3bb712c6a83fbe7a5b03d66cf94030792ba553b6983771c24911e6a4f.jpg

1e50fac9fe799f6a413cd9b7991e5b5110ed4727de192ad1177a7b25353e0fc8.jpg

1e50fac9fe799f6a413cd9b7991e5b5110ed4727de192ad1177a7b25353e0fc8.jpg

2454a481b57619ec50d4089fdede4371cf1b0c4acd80b44d12a0f8d1151a46d3.jpg

2454a481b57619ec50d4089fdede4371cf1b0c4acd80b44d12a0f8d1151a46d3.jpg

ca8b2397120197ef5d0df39762df412bbdd1d5e9c3dc1ad92cfa60ef95db1b1a.jpg

ca8b2397120197ef5d0df39762df412bbdd1d5e9c3dc1ad92cfa60ef95db1b1a.jpg

24d4dee9ae7145cbdaa1b60185377128cf135339c50ef8aeb70af2381f438a22.jpg

24d4dee9ae7145cbdaa1b60185377128cf135339c50ef8aeb70af2381f438a22.jpg

973a49e0b7f2cc2160d88ae45d59dcf5ebf05e5f6858d15f195bf00c3e0292f7.jpg

973a49e0b7f2cc2160d88ae45d59dcf5ebf05e5f6858d15f195bf00c3e0292f7.jpg

886d4de06f4bcf811cccfa639b0a1d87cda549f7f732371cac1a14fdde87dad7.jpg

886d4de06f4bcf811cccfa639b0a1d87cda549f7f732371cac1a14fdde87dad7.jpg

0fbc41d62c0430e1c4edf24d6bef370e2cefec05c40ab2d3cfbe1766a17cc975.jpg

0fbc41d62c0430e1c4edf24d6bef370e2cefec05c40ab2d3cfbe1766a17cc975.jpg

acb1617a2dbd711cf25fcbd6041b40006c5abf3771ccf58b2f399b74a43fdf34.jpg

acb1617a2dbd711cf25fcbd6041b40006c5abf3771ccf58b2f399b74a43fdf34.jpg

56268f20b74208086d401a5c724ca51541e5b7a734e78b6ee4d015a627a43614.jpg

56268f20b74208086d401a5c724ca51541e5b7a734e78b6ee4d015a627a43614.jpg

7e6661d29e85748a5f15e29632887cdb6305ebe1b5756aff8bef878e6d373648.jpg

7e6661d29e85748a5f15e29632887cdb6305ebe1b5756aff8bef878e6d373648.jpg

de99a75fb888556a507f9a5dc7c632a4b3ac5cb5096ce9991a847af600470214.jpg

de99a75fb888556a507f9a5dc7c632a4b3ac5cb5096ce9991a847af600470214.jpg

1246fe3a840a1f8bf6ad69a9697d281c5c2f613b8e3ef05c070f62216932245e.jpg

1246fe3a840a1f8bf6ad69a9697d281c5c2f613b8e3ef05c070f62216932245e.jpg

a09a8b72b68f9a8ee159fb1bb1bbc9fac4523c953be741cd6fa277f91e67f4b7.jpg

a09a8b72b68f9a8ee159fb1bb1bbc9fac4523c953be741cd6fa277f91e67f4b7.jpg

cef5ce49bcd6691072ae19d9d757e76a8fca4359f176033cc70f6f37fcdee1d6.jpg

cef5ce49bcd6691072ae19d9d757e76a8fca4359f176033cc70f6f37fcdee1d6.jpg

61062f4a7e6a7567c7c6c25147c31ea89286ec3a336ccb4fcb530fa982c7b503.jpg

61062f4a7e6a7567c7c6c25147c31ea89286ec3a336ccb4fcb530fa982c7b503.jpg

d37fada43f64cc138720065b526a386c80afd80388db29485d866ca5e2f25302.jpg

d37fada43f64cc138720065b526a386c80afd80388db29485d866ca5e2f25302.jpg

3737ef2984d20de69372a0ac63a24f7dbdd993b4c1be6b5db6563e9b318a3d40.jpg

3737ef2984d20de69372a0ac63a24f7dbdd993b4c1be6b5db6563e9b318a3d40.jpg

5c4d6c1eec42980d2d6e476edd8c387326615f615515d4ac02234b7a6b87c391.jpg

5c4d6c1eec42980d2d6e476edd8c387326615f615515d4ac02234b7a6b87c391.jpg

99a6839ae36e61a1b12d2069fa84fcce62f51e25f711a920f9e0cc816fd14cf4.jpg

99a6839ae36e61a1b12d2069fa84fcce62f51e25f711a920f9e0cc816fd14cf4.jpg

e6ade345f6a2059be5b5d411d239e64198826ce47d90cbc3743082bb7c6e2e4b.jpg

e6ade345f6a2059be5b5d411d239e64198826ce47d90cbc3743082bb7c6e2e4b.jpg

70b8e91d05355febfcef4a327862f0d1cbfb621876808f0f8bc1513134269e30.jpg

70b8e91d05355febfcef4a327862f0d1cbfb621876808f0f8bc1513134269e30.jpg

31d8e71513c12036b8492b7cb912f61a80f16bc3c62c178610d562319289df2d.jpg

31d8e71513c12036b8492b7cb912f61a80f16bc3c62c178610d562319289df2d.jpg

24bb645a598968b5ee69db56ce9fc62f3efc2f68a26ec2bfa5e523fd68f29f72.jpg

24bb645a598968b5ee69db56ce9fc62f3efc2f68a26ec2bfa5e523fd68f29f72.jpg

769829064cdeda193f9e652a598cb7e43ddf1565b82ed2b5cb6f6893c4b2eaa0.jpg

769829064cdeda193f9e652a598cb7e43ddf1565b82ed2b5cb6f6893c4b2eaa0.jpg

cbeee80f9642c0784ea64bda45cd54d41c8019385bd7ed7df434490ac1caf78c.jpg

cbeee80f9642c0784ea64bda45cd54d41c8019385bd7ed7df434490ac1caf78c.jpg

26f131f37af1113f1e956a934a12ace2a9c9c313ce8458feee923c060ae5ffca.jpg

26f131f37af1113f1e956a934a12ace2a9c9c313ce8458feee923c060ae5ffca.jpg

b6b48b2ed4b96df3c39d47d4386534e15ac13c0e3555712f3aa2718e706f067f.jpg

b6b48b2ed4b96df3c39d47d4386534e15ac13c0e3555712f3aa2718e706f067f.jpg

2ab158401eed7237b1c8b3db9f01f2fff71bb40150e2a2edaa029bda7c32a9e7.jpg

2ab158401eed7237b1c8b3db9f01f2fff71bb40150e2a2edaa029bda7c32a9e7.jpg

671f4ea6ffb5e967473a5ef88a7562c2e86c4f9e2fa219bc0cd99c13fcbdf5b0.jpg

671f4ea6ffb5e967473a5ef88a7562c2e86c4f9e2fa219bc0cd99c13fcbdf5b0.jpg

566c37e5db396f28f4df6c64172e1bf83c809e79642c1de34772b1ee4c3216ca.jpg

566c37e5db396f28f4df6c64172e1bf83c809e79642c1de34772b1ee4c3216ca.jpg

ea9035078a7e21281e6f57bb2490fb786158dce4154f3989b3b80bffbd7e9af2.jpg

ea9035078a7e21281e6f57bb2490fb786158dce4154f3989b3b80bffbd7e9af2.jpg

26dbca7b49864c60509dd1f960d589f861e2265e733baca068be6f443ee86023.jpg

26dbca7b49864c60509dd1f960d589f861e2265e733baca068be6f443ee86023.jpg

b5e50d272a8c60a145121e6c7766da98331d3784d3da2b077ba9d6ba97fec10f.jpg

b5e50d272a8c60a145121e6c7766da98331d3784d3da2b077ba9d6ba97fec10f.jpg

f3e7e1c165aff35617facb1d29a6bf35bdbced7c54f0bc439b126fb91e41af9d.jpg

f3e7e1c165aff35617facb1d29a6bf35bdbced7c54f0bc439b126fb91e41af9d.jpg

27ae5162f71a7e06b279c3bda800c37935fc1f08b561a394db19607933450b36.jpg

27ae5162f71a7e06b279c3bda800c37935fc1f08b561a394db19607933450b36.jpg

1ebda965fecc763842700291a9fef472287fda7daca72875fff5cfcdcb088e00.jpg

1ebda965fecc763842700291a9fef472287fda7daca72875fff5cfcdcb088e00.jpg

c4ef5f74a1e394fef75915bbf37a38c73472a62e4a834512227534634c7d7d84.jpg

c4ef5f74a1e394fef75915bbf37a38c73472a62e4a834512227534634c7d7d84.jpg

72e561aee58153f53f7b19ac7aec96f1aa0cbcc2baa1b94aa0c92882a2d4ead3.jpg

72e561aee58153f53f7b19ac7aec96f1aa0cbcc2baa1b94aa0c92882a2d4ead3.jpg

344a37b85a973ab72efee0f1ee48870567dda17b0ec3d4c1f1042c8bedcbea9c.jpg

344a37b85a973ab72efee0f1ee48870567dda17b0ec3d4c1f1042c8bedcbea9c.jpg

a62c8365ca6a63063d7f17ffa4f517ad0e4de972ba7f155d4674641e5b0dac69.jpg

a62c8365ca6a63063d7f17ffa4f517ad0e4de972ba7f155d4674641e5b0dac69.jpg

f8378386b1d0cd2b7a8e87d62cb099c59f31df3d9150abd65b8041a0a8df8498.jpg

f8378386b1d0cd2b7a8e87d62cb099c59f31df3d9150abd65b8041a0a8df8498.jpg

4cf59b8a99742d2496bd26667263a92f53c54946535b7cbaf46b096076af1ed3.jpg

4cf59b8a99742d2496bd26667263a92f53c54946535b7cbaf46b096076af1ed3.jpg

c3764a8304a9755a9abfc6027fe94974089bcdd11e93d2e0a227761a11a9630f.jpg

c3764a8304a9755a9abfc6027fe94974089bcdd11e93d2e0a227761a11a9630f.jpg

6bf31a4fc2482aa8b2a6fb1b5ec68cd03efcb1cad9a38e4c1a5473fad263c2de.jpg

6bf31a4fc2482aa8b2a6fb1b5ec68cd03efcb1cad9a38e4c1a5473fad263c2de.jpg

a8323daf371807cfa6c1db37a176f0dbce1175246aa5034ea1a4414c25ea6203.jpg

a8323daf371807cfa6c1db37a176f0dbce1175246aa5034ea1a4414c25ea6203.jpg

5f6e238d6977406a2005400404bbdf67ea5b8670a9ef282b244c9f07fe9b03ef.jpg

5f6e238d6977406a2005400404bbdf67ea5b8670a9ef282b244c9f07fe9b03ef.jpg

2718e0d8827b6f46bc50c5dca0ad886a8dcf32b5543fea7460dec7ce0696a872.jpg

2718e0d8827b6f46bc50c5dca0ad886a8dcf32b5543fea7460dec7ce0696a872.jpg

9c3ddd28c0810c9dbc1ce48cf918afde97f0684a187f9bc96cbaf589604861c2.jpg

9c3ddd28c0810c9dbc1ce48cf918afde97f0684a187f9bc96cbaf589604861c2.jpg

2e4cec53ac41c9eaa5dab93fae3638238e723a351fbee6c1440adb2b45b8916f.jpg

2e4cec53ac41c9eaa5dab93fae3638238e723a351fbee6c1440adb2b45b8916f.jpg

Agent APIs

Use this datasheet from any agent

Send the page, markdown, chunks, or search endpoint to ChatGPT, Claude, embedr-app, or your own tooling.