Datasheet docs

{ "mpn": "LM2672M-12" }

LM2672M-12

SIMPLE SWITCHER® 12V, 1A Step-Down Voltage Regulator

Power

LM2672 SIMPLE SWITCHER® Power Converter High Efficiency 1-A Step-Down Voltage Regulator with Features

1 Features

1• Efficiency up to 96%

• Available in 8-Pin SOIC and PDIP Packages

• Requires only 5 External Components

• 3.3-V, 5-V, 12-V, and Adjustable Output Versions

• Adjustable Version Output Voltage Range: 1.21 V to 37 V

• ±1.5% Maximum Output Voltage Tolerance Over Line and Load Conditions

• Specified 1-A Output Load Current

• Wide Input Voltage Range: 8 V to 40 V

• 260-kHz Fixed Frequency Internal Oscillator

• TTL Shutdown Capability, Low Power Standby Mode

• Soft-Start and Frequency Synchronization

• Thermal Shutdown and Current Limit Protection

2 Applications

Simple High Efficiency (>90%) Step-Down (Buck) Regulator

• Efficient Preregulator for Linear Regulators

3 Description

The LM2672 series of regulators are monolithic integrated DC-DC converter built with a LMDMOS process. These regulators provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1-A load current with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5 V, 12 V, and an adjustable output version.

Requiring a minimum number of external components, these regulators are simple to use and include patented internal frequency compensation, fixed frequency oscillator, external shutdown, softstart, and frequency synchronization.

The LM2672 series operates at a switching frequency of 260 kHz, thus allowing smaller sized filter components than what is required with lower frequency switching regulators. Because of its very high efficiency (>90%), the copper traces on the printed-circuit board are the only heat sinking required.

Device Information(1)

PART NUMBERPACKAGEBODY SIZE (NOM)
LM2672SOIC (8)5.00 mm × 6.20 mm
PDIP (8)10.16 mm × 6.60 mm
WSON (16)5.00 mm × 5.00 mm

(1) For all available packages, see the orderable addendum at the end of the data sheet.


Fixed output voltage versions
Copyright © 2016, Texas Instruments Incorporated

Table of Contents

1 Features.... 1 2 Applications.... 1 3 Description.... 1 4 Revision History.... 2 5 Description (continued).... 3 6 Pin Configuration and Functions.... 3 7 Specifications.... 4 7.1 Absolute Maximum Ratings.... 4 7.2 ESD Ratings.... 4 7.3 Recommended Operating Conditions.... 4 7.4 Thermal Information.... 4 7.5 Electrical Characteristics – 3.3 V.... 5 7.6 Electrical Characteristics – 5 V.... 5 7.7 Electrical Characteristics – 12 V.... 5 7.8 Electrical Characteristics – Adjustable.... 6 7.9 Electrical Characteristics – All Output Voltage Versions.... 6 7.10 Typical Characteristics.... 7 7.11 Typical Characteristics – Fixed Output Voltage Versions.... 9 8 Parameter Measurement Information.... 10 9 Detailed Description.... 11

9.1 Overview.... 11 9.2 Functional Block Diagram.... 11 9.3 Feature Description.... 11 9.4 Device Functional Modes.... 12 10 Application and Implementation.... 13 10.1 Application Information.... 13 10.2 Typical Applications.... 14 11 Power Supply Recommendations.... 25 12 Layout.... 25 12.1 Layout Guidelines.... 25 12.2 Layout Examples.... 25 13 Device and Documentation Support.... 27 13.1 Documentation Support.... 27 13.2 Receiving Notification of Documentation Updates.... 27 13.3 Community Resources.... 27 13.4 Trademarks.... 27 13.5 Electrostatic Discharge Caution.... 27 13.6 Glossary.... 27 14 Mechanical, Packaging, and Orderable Information.... 27 14.1 DAP (WSON Package).... 27

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision K (April 2013) to Revision L

Page

Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .... 1

• Removed all references to Computer Design Software LM267X Made Simple (Version 6.0)......... ................

Changes from Revision J (April 2013) to Revision K

- Changed layout of National Data Sheet to TI format .... 1

5 Description (continued)

A family of standard inductors for use with the LM2672 are available from several different manufacturers. This feature greatly simplifies the design of switch-mode power supplies using these advanced ICs. Also included in the datasheet are selector guides for diodes and capacitors designed to work in switch-mode power supplies.

Other features include ±1.5%-tolerance on output voltage within specified input voltages and output load conditions, and ±10% on the oscillator frequency. External shutdown is included, featuring typically 50 $\mu { \sf A }$ standby current. The output switch includes current limiting, as well as thermal shutdown for full protection under fault conditions.

6 Pin Configuration and Functions

Pin Functions

PINI/ODESCRIPTION
NAMESOIC, PDIPWSON
$C_B$ 11IBoot-strap capacitor connection for high-side driver. Connect a high quality 100-nF capacitor from $C_B$ to $V_{SW}$ Pin.
FB48IFeedback sense input pin. Connect to the midpoint of feedback divider to set VOUT for ADJ version or connect this pin directly to the output capacitor for a fixed output version.
GND611, 12—Power ground pins. Connect to system ground. Ground pins of $C_{IN}$ and $C_{OUT}$ . Path to $C_{IN}$ must be as short as possible.
NC—2, 3, 5, 7, 10, 13—No connection pins.
ON/OFF59IEnable input to the voltage regulator. High = ON and low = OFF. Pull this pin high or float to enable the regulator.
SS24ISoft-start capacitor pin. Connect a capacitor from this pin to GND to control the output voltage ramp. If the feature not desired, the pin can be left floating.
SYNC36IThis input allows control of the switching clock frequency. If left open-circuited the regulator is switched at the internal oscillator frequency, typically 260 kHz.
$V_{IN}$ 714ISupply input pin to collector pin of high side FET. Connect to power supply and input bypass capacitors $C_{IN}$ . Path from $V_{IN}$ pin to high frequency bypass $C_{IN}$ and GND must be as short as possible.
$V_{SW}$ 815, 16OSource pin of the internal High Side FET. This is a switching node. Attached this pin to an inductor and the cathode of the external diode.

7 Specifications

7.1 Absolute Maximum Ratings

over recommended operating junction temperature range of $\scriptscriptstyle - 4 0 ^ { \circ } \mathsf { C }$ to $1 2 5 ^ { \circ } \mathrm { C }$ (unless otherwise noted)(1)

MINMAXUNIT
Supply voltage45V
ON/OFF pin voltage, VSH-0.16V
Switch voltage to ground-1V
Boost pin voltageVSW+8V
Feedback pin voltage, VFB-0.314V
Power dissipationInternally limited
Lead temperatureD packageVapor phase (60s)215°C
Infrared (15s)220
P package (soldering, 10s)260
Maximum junction temperature, TJ150°C
Storage temperature, Tstg-65150°C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

7.2 ESD Ratings

VALUEUNIT
$V_{(ESD)}$ Electrostatic dischargeHuman-body model (HBM), per ANSI/ESDA/JEDEC JS-001 $^{(1)}$ ±2000V

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)

MINMAXUNIT
Supply voltage6.540V
$T_J$ Operating junction temperature-40125°C

7.4 Thermal Information

THERMAL METRIC(1)(2)LM2672UNIT
D (SOIC)P (PDIP)WSON (NHN)
8 PINS8 PINS16 PINS
$R_{\theta JA}$ Junction-to-ambient thermal resistance10595—°C/W
$R_{\theta JC(top)}$ Junction-to-case (top) thermal resistance———°C/W
$R_{\theta JB}$ Junction-to-board thermal resistance———°C/W
$\psi_{JT}$ Junction-to-top characterization parameter———°C/W
$\psi_{JB}$ Junction-to-board characterization parameter———°C/W
$R_{\theta JC(bot)}$ Junction-to-case (bottom) thermal resistance———°C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report.
(2) Thermal resistances were simulated on 4-layer JEDEC board.

7.5 Electrical Characteristics – 3.3 V

${ \sf T } _ { \mathrm { J } } = 2 5 ^ { \circ } { \sf C }$ (unless otherwise noted; see Figure 19)(1)

PARAMETERTEST CONDITIONSMIN(2)TYP(3)MAX(2)UNIT
$V_{OUT}$ Output voltage $V_{IN}=8 V to 40 V, I_{LOAD}=20 mA to 1 A$ $T_J=25°C$ 3.2513.33.35V
$T_J=-40°C to 125°C$ 3.2013.399
$V_{IN}=6.5 V to 40 V, I_{LOAD}=20 mA to 500 mA$ $T_J=25°C$ 3.353.33.35
$T_J=-40°C to 125°C$ 3.2013.399
ηEfficiency $V_{IN}=12 V, I_{LOAD}=1 A$ 86%

(1) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator performance. When the LM2672 is used as shown in Figure 19 test circuits, system performance is as specified by the system parameters section of Electrical Characteristics.

(2) All limits specified at room temperature and at temperature extremes. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).

(3) Typical numbers are at 25°C and represent the most likely norm.

7.6 Electrical Characteristics – 5 V

T = 25°C (unless otherwise noted; see Figure 19)(1)

PARAMETERTEST CONDITIONSMIN(2)TYP(3)MAX(2)UNIT
$V_{OUT}$ Output voltage $V_{IN}=8 V to 40 V, I_{LOAD}=20 mA to 1 A$ $T_J=25°C$ 4.92555.075V
$T_J=-40°C to 125°C$ 4.855.15
$V_{IN}=6.5 V to 40 V, I_{LOAD}=20 mA to 500 mA$ $T_J=25°C$ 4.92555.075
$T_J=-40°C to 125°C$ 4.855.15
ηEfficiency $V_{IN}=12 V, I_{LOAD}=1 A$ 90%

(1) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator performance. When the LM2672 is used as shown in Figure 19 test circuits, system performance is as specified by the system parameters section of Electrical Characteristics.

(2) All limits specified at room temperature and at temperature extremes. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).

(3) Typical numbers are at 25°C and represent the most likely norm.

7.7 Electrical Characteristics – 12 V

${ \sf T } _ { \mathrm { J } } = 2 5 ^ { \circ } { \sf C }$ (unless otherwise noted; see Figure 19)(1)

PARAMETERTEST CONDITIONSMIN(2)TYP(3)MAX(2)UNIT
$V_{OUT}$ Output voltage $V_{IN} = 15 \text{ V to } 40 \text{ V, } I_{LOAD} = 20 \text{ mA to } 1 \text{ A}$ $T_J = 25°C$ 11.821212.18V
$T_J = -40°C \text{ to } 125°C$ 11.6412.36
$\eta$ Efficiency $V_{IN} = 24 \text{ V, } I_{LOAD} = 1 \text{ A}$ 94%

(1) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator performance. When the LM2672 is used as shown in Figure 19 test circuits, system performance is as specified by the system parameters section of Electrical Characteristics.

(2) All limits specified at room temperature and at temperature extremes. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).

(3) Typical numbers are at 25°C and represent the most likely norm.

7.8 Electrical Characteristics – Adjustable

${ \sf T } _ { \mathrm { J } } = 2 5 ^ { \circ } { \sf C }$ (unless otherwise noted; see Figure 19)(1)

PARAMETERTEST CONDITIONSMIN(2)TYP(3)MAX(2)UNIT
$V_{FB}$ Feedback voltage $V_{IN}=8 V to 40 V, I_{LOAD}=20 mA to 1 A, V_{OUT}programmed for 5 V (see Figure 19)\(T_J=25°C$ 1.1921.211.228V
$T_J=-40°C to 125°C$ 1.1741.246
$V_{IN}=6.5 V to 40 V, I_{LOAD}=20 mA to 500 mA, V_{OUT}programmed for 5 V (see Figure 19)\(T_J=25°C$ 1.1921.211.228
$T_J=-40°C to 125°C$ 1.1741.246
ηEfficiency $V_{IN}=12 V, I_{LOAD}=1 A$ 90%

(1) External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator performance. When the LM2672 is used as shown in Figure 19 test circuits, system performance is as specified by the system parameters section of Electrical Characteristics.

(2) All limits specified at room temperature and at temperature extremes. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).

(3) Typical numbers are at $2 5 ^ { \circ } \mathrm { C }$ and represent the most likely norm.

7.9 Electrical Characteristics – All Output Voltage Versions

$\mathsf { T } _ { \mathsf { J } } = 2 5 ^ { \circ } \mathsf { C } , \mathsf { V } _ { \mathsf { I N } } = 1 2 \mathsf { V }$ for the 3.3 V, 5 V, and Adjustable versions and $\mathsf { V } _ { \mathsf { I N } } = 2 4 \mathsf { V }$ for the 12V version, and $\mathsf { I } _ { \mathsf { L O A D } } = 1 0 0 \mathsf { m A }$ (unless otherwise noted)

PARAMETERTEST CONDITIONSMIN(1)TYP(2)MAX(1)UNIT
$I_Q$ Quiescent current $V_{FEEDBACK}=8 V for 3.3 V, 5 V, and adjustable versions2.53.6mA
\(V_{FEEDBACK}=15 V for 12 V versions2.5
\(I_{STBY}$ Standby quiescent currentON/OFF Pin = 0 V $T_J=25°C$ 50100μA
$T_J=-40°C to 125°C$ 150
$I_{CL}$ Current limit1.251.552.1A
1.22.2
$I_L$ Output leakage current $V_{SWITCH}=0 V, ON/OFF Pin=0 V, V_{IN}=40 V$ 125μA
$V_{SWITCH}=-1 V, ON/OFF Pin=0 V$ 615mA
$R_{DS(ON)}$ Switch on-resistance $I_{SWITCH}=1 A$ $T_J=25°C$ 0.250.3Ω
$T_J=-40°C to 125°C$ 0.5
$f_O$ Oscillator frequencyMeasured at switch pin $T_J=25°C$ 260kHz
$T_J=-40°C to 125°C$ 225275
DMaximum duty cycle $T_J=25°C$ 95%
Minimum duty cycle $T_J=-40°C to 125°C$ 0%
$I_{BIAS}$ Feedback bias current $V_{FEEDBACK}=1.3 V, adjustable version only$ 85nA
$V_{S/D}$ ON/OFF pin voltage $T_J=25°C$ 1.4V
$T_J=-40°C to 125°C$ 0.82
$I_{S/D}$ ON/OFF pin currentON/OFF Pin = 0 V $T_J=25°C$ 20μA
$T_J=-40°C to 125°C$ 737
$F_{SYNC}$ Synchronization frequency $V_{SYNC}=3.5 V, 50\% duty cycle$ 400kHz
$V_{SYNC}$ Synchronization threshold voltage1.4V
$V_{SS}$ Soft-start voltage $T_J=25°C$ 0.63V
$T_J=-40°C to 125°C$ 0.530.73
$I_{SS}$ Soft-start current $T_J=25°C$ 4.5μA
$T_J=-40°C to 125°C$ 1.56.9

(1) All limits specified at room temperature and at temperature extremes. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(2) Typical numbers are at 25°C and represent the most likely norm.

7.10 Typical Characteristics


JUNCTION TEMPERATURE (°C)

Figure 1. Normalized Output Voltage

INPUT VOLTAGE (V)

Figure 3. Efficiency

Figure 5. Switch Current Limit
JUNCTION TEMPERATURE (°C)

Figure 2. Line Regulation

JUNCTION TEMPERATURE (°C)

Figure 4. Drain-to-Source Resistance

JUNCTION TEMPERATURE (°C)
Figure 6. Operating Quiescent Current

Typical Characteristics (continued)

Figure 7. Standby Quiescent CurrentFigure 8. ON/OFF Threshold Voltage
Figure 9. ON/OFF Pin Current (Sourcing)Figure 10. Switching Frequency
Figure 11. Feedback Pin Bias CurrentFigure 12. Peak Switch Current

Output ripple voltage, 20 mV/div AC-coupled

Inductor current, 0.5 A/div

V pin voltage, 10 V/div Inductor current, 0.5 A/div Output ripple voltage, 20 mV/div AC-coupled

Typical Characteristics (continued)


Figure 13. Dropout Voltage, 3.3-V Option


Figure 14. Dropout Voltage, 5-V Option

7.11 Typical Characteristics – Fixed Output Voltage Versions see Figure 19

V pin voltage, 10 V/div

$$ V _ {I N} = 2 0 \mathrm{V}, V _ {O U T} = 5 \mathrm{V}, $$

$$ I _ {L O A D} = 1 \mathrm{A}, L = 4 7 \mu \mathrm{H}, $$

COUTESR = 50 mΩ

$$ V _ {I N} = 2 0 \mathrm{V}, V _ {O U T} = 5 \mathrm{V}, $$

ILOAD = 300 mA, L = 15 μH,

COUT = 68 μF (2×),

COUTESR = 25 mΩ

Figure 15. Continuous Mode Switching Waveforms, Horizontal Time Base: 1 μs/div

Figure 16. Discontinuous Mode Switching Waveforms, Horizontal Time Base: 1 μs/div

Output voltage,

100 mV/div, AC-coupled

$$ V _ {I N} = 2 0 \mathrm{V}, V _ {O U T} = 5 \mathrm{V}, $$

Load current: 200 mA to 1 A load pulse

$$ I _ {L O A D} = 1 \mathrm{A}, L = 4 7 \mu \mathrm{H}, $$

$$ C _ {O U T} = 6 8 \mu F, $$

COUTESR = 50 mΩ

Figure 17. Load Transient Response for Continuous Mode, Horizontal Time Base: 50 μs/div

Output voltage,

$$ V _ {I N} = 2 0 \mathrm{V}, V _ {O U T} = 5 \mathrm{V}, $$

100 mV/div, AC-coupled

$$ \mathrm{L} = 4 7 \mu \mathrm{H}, $$

Load current: 100 mA to 300 mA load pulse

$$ \mathrm{C} _ {\text { OUT }} = 6 8 \mu \mathrm{F}, $$

COUTESR = 50 mΩ

Figure 18. Load Transient Response for Discontinuous Mode, Horizontal Time Base: 200 μs/div

8 Parameter Measurement Information


Copyright © 2016, Texas Instruments Incorporated

CIN = 22-μF, 50-V Tantalum Sprague 199D Series

COUT = 47-μF, 25-V Tantalum Sprague 595D Series

D1 = 3.3-A, 50-V Schottky Rectifier, IR 30WQ05F

L1 = 68-μH Sumida #RCR110D-680L

$\mathsf { C } _ { \mathsf { B } } = 0 . 0 1 \mathsf { - \mu F }$ , 50-V ceramic

Figure 19. Standard Test Circuits and Layout Guides, Fixed Output Voltage Versions

9 Detailed Description

9.1 Overview

The LM2672 provides all of the active functions required for a step-down (buck) switching regulator. The internal power switch is a DMOS power MOSFET to provide power supply designs with high current capability, up to 1 A, and highly efficient operation.

The LM2672 is part of the SIMPLE SWITCHER® family of power converters. A complete design uses a minimum number of external components, which have been pre-determined from a variety of manufacturers. Using either this data sheet or TI's WEBENCH® design tool, a complete switching power supply can be designed quickly. Refer to LM2670 SIMPLE SWITCHER® High Efficiency 3A Step-Down Voltage Regulator with Sync for additional application information.

9.2 Functional Block Diagram

9.3 Feature Description

9.3.1 Switch Output

This is the output of a power MOSFET switch connected directly to the input voltage. The switch provides energy to an inductor, an output capacitor and the load circuitry under control of an internal pulse-width-modulator (PWM). The PWM controller is internally clocked by a fixed 260-kHz oscillator. In a standard step-down application the duty cycle (time ON or time OFF) of the power switch is proportional to the ratio of the power supply output voltage to the input voltage. The voltage on the $\mathsf { V } _ { \mathsf { S W } }$ pin cycles between $\mathsf { V } _ { \mathsf { i n } }$ (switch ON) and below ground by the voltage drop of the external Schottky diode (switch OFF).

Feature Description (continued)

9.3.2 C Boost

A capacitor must be connected from the $C _ { \mathsf { B } }$ pin to the $\mathsf { V } _ { \mathsf { S W } }$ pin. This capacitor boosts the gate drive to the internal MOSFET above $\mathsf { V } _ { \mathsf { i n } }$ to fully turn it ON. This minimizes conduction losses in the power switch to maintain high efficiency. The recommended value for C Boost is 0.01 $\mu \mathsf { F }$

9.3.3 SYNC

This input allows control of the switching clock frequency. If left open-circuited the regulator is switched at the internal oscillator frequency, typically 260 kHz. An external clock can be used to force the switching frequency and thereby control the output ripple frequency of the regulator. This capability provides for consistent filtering of the output ripple from system to system as well as precise frequency spectrum positioning of the ripple frequency which is often desired in communications and radio applications. This external frequency must be greater than the LM2672 internal oscillator frequency, which could be as high as 275 kHz, to prevent an erroneous reset of the internal ramp oscillator and PWM control of the power switch. The ramp oscillator is reset on the positive going edge of the sync input signal. TI recommends that the external TTL or CMOS compatible clock (between 0 V and a level greater than 3 V) be AC-coupled to the SYNC pin through a 100-pF capacitor and a 1-kΩ resistor to ground.

When the SYNC function is used, current limit frequency foldback is not active. Therefore, the device may not be fully protected against extreme output short circuit conditions.

9.3.4 Feedback

This is the input to a two-stage high gain amplifier, which drives the PWM controller. Connect the FB pin directly to the output for proper regulation. For the fixed output devices (3.3-V, 5-V, and 12-V outputs), a direct wire connection to the output is all that is required as internal gain setting resistors are provided inside the LM2672. For the adjustable output version two external resistors are required to set the DC output voltage. For stable operation of the power supply, it is important to prevent coupling of any inductor flux to the feedback input.

9.4 Device Functional Modes

9.4.1 ON/OFF

This input provides an electrical ON/OFF control of the power supply. Connecting this pin to ground or to any voltage less than 1.4 V completely turns OFF the regulator. The current drain from the input supply when OFF is only ${ \bar { 5 } } 0 ~ \mu \mathsf { A } .$ . The ON/OFF input has an internal pullup current source of approximately 20 μA and a protection clamp Zener diode of 7 V to ground. When electrically driving the ON/OFF pin the high voltage level for the ON condition must not exceed the 6-V absolute maximum limit. When ON/OFF control is not required this pin must be left open.

9.4.2 Shutdown Mode

The ON/OFF pin provides electrical ON and OFF control for the LM2671. When the voltage of this pin is lower than 1.4 $\vee ,$ the device is shutdown mode. The typical standby current in this mode is 50 $\mu { \sf A } ,$

9.4.3 Active Mode

When the voltage of the ON/OFF pin is higher than 1.4 V, the device starts switching and the output voltage rises until it reaches a normal regulation voltage.

10 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality.

10.1 Application Information

The LM2672 is a step-down DC-DC regulator. It is typically used to convert a higher DC voltage to a lower DC voltage with a maximum output current of 1 A. The following design procedure can be used to select components for the LM2672.

When the output voltage is greater than approximately 6 V, and the duty cycle at minimum input voltage is greater than approximately 50%, the designer must exercise caution in selection of the output filter components. When an application designed to these specific operating conditions is subjected to a current limit fault condition, it may be possible to observe a large hysteresis in the current limit. This can affect the output voltage of the device until the load current is reduced sufficiently to allow the current limit protection circuit to reset itself.

Under current limiting conditions, the LM267x is designed to respond in the following manner:

  1. At the moment when the inductor current reaches the current limit threshold, the ON-pulse is immediately terminated. This happens for any application condition.

  2. However, the current limit block is also designed to momentarily reduce the duty cycle to below 50% to avoid subharmonic oscillations, which could cause the inductor to saturate.

  3. Thereafter, once the inductor current falls below the current limit threshold, there is a small relaxation time during which the duty cycle progressively rises back above 50% to the value required to achieve regulation.

If the output capacitance is sufficiently large, it may be possible that as the output tries to recover, the output capacitor charging current is large enough to repeatedly re-trigger the current limit circuit before the output has fully settled. This condition is exacerbated with higher output voltage settings because the energy requirement of the output capacitor varies as the square of the output voltage (½ CV2), thus requiring an increased charging current. A simple test to determine if this condition might exist for a suspect application is to apply a short circuit across the output of the converter, and then remove the shorted output condition. In an application with properly selected external components, the output recovers smoothly. Practical values of external components that have been experimentally found to work well under these specific operating conditions are COUT = 47 µF, L = 22 µH. Note that even with these components, for a device’s current limit of ICLIM, the maximum load current under which the possibility of the large current limit hysteresis can be minimized is I /2. For example, if the input is 24 V and the set output voltage is 18 V, then for a desired maximum current of 1.5 A, the current limit of the chosen switcher must be confirmed to be at least 3 A. Under extreme overcurrent or short-circuit conditions, the LM267X employs frequency foldback in addition to the current limit. If the cycle-by-cycle inductor current increases above the current limit threshold (due to short circuit or inductor saturation for example) the switching frequency is automatically reduced to protect the IC. Frequency below 100 KHz is typical for an extreme shortcircuit condition.

10.2 Typical Applications

10.2.1 Typical Application for Fixed Output Voltage Versions


Copyright © 2016, Texas Instruments Incorporated
L1 = 68-μH Sumida #RCR110D-680L
CB = 0.01-μF, 50-V Ceramic

Figure 20. Fixed Output Voltage Typical Application

10.2.1.1 Design Requirements

Table 1 lists the design requirements for the fixed output voltage application.

Table 1. Fixed Output Voltage Application Parameters

PARAMETERVALUE
Regulated output voltage (3.3 V, 5 V, or 12 V), $V_{OUT}$ 5 V
Maximum DC input voltage, $V_{IN}$ (max)12 V
Maximum load current, $I_{LOAD}$ (max)1 A

10.2.1.2 Detailed Design Procedure

10.2.1.2.1 Inductor Selection (L1)

First, select the correct inductor value selection guide from Figure 23, Figure 24, or Figure 25 (output voltages of 3.3-V, 5-V, or 12-V respectively). For all other voltages, see the design procedure for the adjustable version. Use the inductor selection guide for the 5-V version shown in Figure 24.

From the inductor value selection guide, identify the inductance region intersected by the maximum input voltage line and the maximum load current line. Each region is identified by an inductance value and an inductor code (LXX). From the inductor value selection guide shown in Figure 24, the inductance region intersected by the 12 V horizontal line and the 1 A vertical line is 33 μH, and the inductor code is L23.

Select an appropriate inductor from the four manufacturer's part numbers listed in Table 2. Each manufacturer makes a different style of inductor to allow flexibility in meeting various design requirements. The inductance value required is 33 μH. From Table 2, go to the L23 line and choose an inductor part number from any of the four manufacturers shown. In most instances, both through hole and surface mount inductors are available.

Table 2. Inductor Manufacturers' Part Numbers

IND. REF. DESG.INDUCTANCE (μH)CURRENT (A)SCHOTTRENCOPULSE ENGINEERINGCOILCRAFT
THROUGH HOLESURFACE MOUNTTHROUGH HOLESURFACE MOUNTTHROUGH HOLESURFACE MOUNTSURFACE MOUNT
L4680.326714394067144310RL-1284-68-43RL1500-68PE-53804PE-53804-SDO1608-683
L5470.376714831067148420RL-1284-47-43RL1500-47PE-53805PE-53805-SDO1608-473
L6330.446714832067148430RL-1284-33-43RL1500-33PE-53806PE-53806-SDO1608-333
L7220.526714833067148440RL-1284-22-43RL1500-22PE-53807PE-53807-SDO1608-223
L92200.326714396067144330RL-5470-3RL1500-220PE-53809PE-53809-SDO3308-224
L101500.396714397067144340RL-5470-4RL1500-150PE-53810PE-53810-SDO3308-154
L111000.486714398067144350RL-5470-5RL1500-100PE-53811PE-53811-SDO3308-104
L12680.586714399067144360RL-5470-6RL1500-68PE-53812PE-53812-SDO3308-683
L13470.706714400067144380RL-5470-7RL1500-47PE-53813PE-53813-SDO3308-473
L14330.836714834067148450RL-1284-33-43RL1500-33PE-53814PE-53814-SDO3308-333
L15220.996714835067148460RL-1284-22-43RL1500-22PE-53815PE-53815-SDO3308-223
L182200.556714404067144420RL-5471-2RL1500-220PE-53818PE-53818-SDO3316-224
L191500.666714405067144430RL-5471-3RL1500-150PE-53819PE-53819-SDO3316-154
L201000.826714406067144440RL-5471-4RL1500-100PE-53820PE-53820-SDO3316-104
L21680.996714407067144450RL-5471-5RL1500-68PE-53821PE-53821-SDO3316-683
L22471.176714408067144460RL-5471-6—PE-53822PE-53822-SDO3316-473
L23331.46714409067144470RL-5471-7—PE-53823PE-53823-SDO3316-333
L24221.76714837067148480RL-1283-22-43—PE-53824PE-53824-SDO3316-223
L2722016714411067144490RL-5471-2—PE-53827PE-53827-SDO5022P-224
L281501.26714412067144500RL-5471-3—PE-53828PE-53828-SDO5022P-154
L291001.476714413067144510RL-5471-4—PE-53829PE-53829-SDO5022P-104
L30681.786714414067144520RL-5471-5—PE-53830PE-53830-SDO5022P-683

10.2.1.2.2 Output Capacitor Selection (C )

Select an output capacitor from the output capacitor table in Table 3. Using the output voltage and the inductance value found in the inductor selection guide, step 1, locate the appropriate capacitor value and voltage rating. Use the 5-V section in Table 3. Choose a capacitor value and voltage rating from the line that contains the inductance value of 33 μH. The capacitance and voltage rating values corresponding to the 33 μH.

The capacitor list contains through-hole electrolytic capacitors from four different capacitor manufacturers and surface mount tantalum capacitors from two different capacitor manufacturers.

Surface mount:

• 68-μF, 10-V Sprague 594D series

• 100-μF, 10-V AVX TPS series

Through hole:

• 68-μF, 10-V Sanyo OS-CON SA series

• 220-μF, 35-V Sanyo MV-GX series

• 220-μF, 35-V Nichicon PL series

• 220-μF, 35-V Panasonic HFQ series

Table 3. Output Capacitor Table

OUTPUT VOLTAGE (V)INDUCTANCE (μH)OUTPUT CAPACITOR
SURFACE MOUNTTHROUGH HOLE
SPRAGUE 594D SERIES (μF/V)AVX TPS SERIES (μF/V)SANYO OS-CON SA SERIES (μF/V)SANYO MV-GX SERIES (μF/V)NICHICON PL SERIES (μF/V)PANASONIC HFQ SERIES (μF/V)
3.322120/6.3100/10100/10330/35330/35330/35
33120/6.3100/1068/10220/35220/35220/35
4768/10100/1068/10150/35150/35150/35
68120/6.3100/10100/10120/35120/35120/35
100120/6.3100/10100/10120/35120/35120/35
150120/6.3100/10100/10120/35120/35120/35
522100/16100/10100/10330/35330/35330/35
3368/10100/1068/10220/35220/35220/35
4768/10100/1068/10150/35150/35150/35
68100/16100/10100/10120/35120/35120/35
100100/16100/10100/10120/35120/35120/35
150100/16100/10100/10120/35120/35120/35
1222120/20(2×) 68/2068/20330/35330/35330/35
3368/2568/2068/20220/35220/35220/35
4747/2068/2047/20150/35150/35150/35
6847/2068/2047/20120/35120/35120/35
10047/2068/2047/20120/35120/35120/35
15047/2068/2047/20120/35120/35120/35
22047/2068/2047/20120/35120/35120/35

10.2.1.2.3 Catch Diode Selection (D1)

In normal operation, the average current of the catch diode is the load current times the catch diode duty cycle, 1-D (D is the switch duty cycle, which is approximately the output voltage divided by the input voltage). The largest value of the catch diode average current occurs at the maximum load current and maximum input voltage (minimum D). For normal operation, the catch diode current rating must be at least 1.3 times greater than its maximum average current. However, if the power supply design must withstand a continuous output short, the diode must have a current rating equal to the maximum current limit of the LM2672. The most stressful condition for this diode is a shorted output condition. Refer to the table shown in Table 4. In this example, a 1-A, 20-V Schottky diode provides the best performance. If the circuit must withstand a continuous shorted output, a higher current Schottky diode is recommended.

The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best performance and efficiency. This Schottky diode must be placed close to the LM2672 using short leads and short printed circuit traces.

Table 4. Schottky Diode Selection Table

$V_R$ 1-A DIODES3-A DIODES
SURFACE MOUNTTHROUGH HOLESURFACE MOUNTTHROUGH HOLE
20 VSK121N5817SK321N5820
B120SR102—SR302
30 VSK131N5818SK331N5821
B13011DQ0330WQ03F31DQ03
MBRS130SR103——
40 VSK141N5819SK341N5822
B14011DQ0430BQ040MBR340
MBRS140SR10430WQ04F31DQ04
10BQ040—MBRS340SR304
10MQ040—MBRD340—
15MQ040———
50 VSK15MBR150SK35MBR350
B15011DQ0530WQ05F31DQ05
10BQ050SR105—SR305

10.2.1.2.4 Input Capacitor $( \mathsf { C } _ { \mathsf { I N } } )$

A low ESR aluminum or tantalum bypass capacitor is required between the input pin and ground to prevent large voltage transients from appearing at the input. This capacitor must be placed close to the IC using short leads. In addition, the RMS current rating of the input capacitor must be selected to be at least ½ the DC load current. The capacitor manufacturer data sheet must be checked to assure that this current rating is not exceeded. Figure 21 shows typical RMS current ratings for several different aluminum electrolytic capacitor values. A paralle connection of two or more capacitors may be required to increase the total minimum RMS current rating to suit the application requirements.


Figure 21. RMS Current Ratings for Low ESR Electrolytic Capacitors (Typical)

For an aluminum electrolytic capacitor, the voltage rating must be at least 1.25 times the maximum input voltage. Caution must be exercised if solid tantalum capacitors are used. The tantalum capacitor voltage rating must be twice the maximum input voltage. The tables in Table 5 show the recommended application voltage for AVX TPS and Sprague 594D tantalum capacitors. It is also recommended that they be surge current tested by the manufacturer. The TPS series available from AVX, and the 593D and 594D series from Sprague are all surge current tested. Another approach to minimize the surge current stresses on the input capacitor is to add a small inductor in series with the input supply line.

Table 5. Recommended Application Voltage for AVX TPS and Sprague 594D Tantalum Chip Capacitors Derated for $\mathtt { \pmb { 8 5 } ^ { \circ } C }$

RECOMMENDED APPLICATION VOLTAGEVOLTAGE RATING
3.36.3
510
1020
1225
1535

Use caution when using ceramic capacitors for input bypassing, because it may cause severe ringing at the $V _ { \sf I N }$ pin.

The important parameters for the input capacitor are the input voltage rating and the RMS current rating. With a maximum input voltage of 12 V, an aluminum electrolytic capacitor with a voltage rating greater than 15 V (1.25 × $\mathsf { V } _ { \mathsf { I N } } )$ is required. The next higher capacitor voltage rating is 16 V.

The RMS current rating requirement for the input capacitor in a buck regulator is approximately ½ the DC load current. In this example, with a 1-A load, a capacitor with a RMS current rating of at least 500 mA is required. The curves shown in Figure 21 can be used to select an appropriate input capacitor. From the curves, locate the 16-V line and note which capacitor values have RMS current ratings greater than 500 mA.

For a through hole design, a 330-μF, 16-V electrolytic capacitor (Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or equivalent) would be adequate. Other types or other manufacturers' capacitors can be used provided the RMS ripple current ratings are adequate. Additionally, for a complete surface mount design, electrolytic capacitors such as the Sanyo CV-C or CV-BS and the Nichicon WF or UR and the NIC Components NACZ series could be considered.

For surface mount designs, solid tantalum capacitors can be used, but caution must be exercised with regard to the capacitor surge current rating and voltage rating. In this example, checking Table 5, and the Sprague 594D series data sheet, a Sprague 594D 15-μF, 25-V capacitor is adequate.

10.2.1.2.5 Boost Capacitor $( C _ { \mathsf { B } } )$

This capacitor develops the necessary voltage to turn the switch gate on fully. All applications must use a 0.01- μF, 50-V ceramic capacitor.

10.2.1.2.6 Soft-Start Capacitor $( \cos ,$ , Optional)

This capacitor controls the rate at which the device starts up. The formula for the soft-start capacitor $\mathtt { C } _ { \mathtt { S S } }$ is calculated with Equation 1.

$$ C _ {S S} \approx \left(I _ {S S} \cdot t _ {S S}\right) / \left[ V _ {S S T H} + 2. 6 V \cdot \left(\frac {V _ {O U T} + V _ {S C H O T T K Y}}{V _ {I N}}\right) \right] $$

where

• ISS = Soft-start current (4.5 µA, typical)

$\mathfrak { t } _ { \mathbb { S } \mathbb { S } } =$ Soft-start time (selected)

$\mathsf { V } _ { \mathsf { S S T H } }$ = Soft-start threshold voltage (0.63 V, typical)

$\mathsf { V } _ { \mathsf { O U T } } = ($ Output voltage (selected)

$\mathsf { V } _ { \mathsf { S C H O T T K Y } } = \mathsf { S c h o t t k y }$ diode voltage drop (0.4 V, typical)

• VIN = Input voltage (selected)

(1)

If this feature is not desired, leave this pin open. With certain soft-start capacitor values and operating conditions, the LM2672 can exhibit an overshoot on the output voltage during turn on. Especially when starting up into no load or low load, the soft-start function may not be effective in preventing a larger voltage overshoot on the output. With larger loads or lower input voltages during startup this effect is minimized. In particular, avoid using soft-start capacitors between 0.033 $\mathsf { \Pi } \dot { \mu } \mathsf { F }$ and 1 µF.

For this application, selecting a start-up time of 10 ms and using the formula for $\mathtt { C } _ { \mathtt { S S } }$ results in a value of Equation 2.

$$ \begin{array}{r l} C _ {S S} \approx (4. 5 \mu A \cdot 1 0 m s) / [ 0. 6 3 V + 2. 6 V \cdot (\frac {5 V + 0 . 4 V}{1 2 V}) ] \ = 2 5 n F \approx 0. 0 2 2 \mu F. \end{array}\tag{2} $$

10.2.1.2.7 Frequency Synchronization (Optional)

The LM2672 (oscillator) can be synchronized to run with an external oscillator, using the sync pin (pin 3). By doing so, the LM2672 can be operated at higher frequencies than the standard frequency of 260 kHz. This allows for a reduction in the size of the inductor and output capacitor.

As shown in Figure 22, a signal applied to a RC filter at the sync pin causes the device to synchronize to the frequency of that signal. For a signal with a peak-to-peak amplitude of 3 V or greater, a 1-kΩ resistor and a 100- pF capacitor are suitable values. For all applications, use a 1-kΩ resistor and a 100-pF capacitor for the RC filter.


Figure 22. Synchronization on LM2672

10.2.1.3 Application Curves

Figure 23. LM2672, 3.3-V Output


MAXIMUM LOAD CURRENT (A) Figure 24. LM2672, 5-V Output


Figure 25. LM2672, 12-V Output

10.2.2 Typical Application for Adjustable Output Voltage Versions


Copyright © 2016, Texas Instruments Incorporated

CIN = 22-μF, 50-V Tantalum, Sprague 199D Series

D1 = 3.3-A, 50-V Schottky Rectifier, IR 30WQ05F

R1 = 1.5-kΩ , 1%

$\mathsf { C } _ { \mathsf { B } } = 0 . 0 1 \mathsf { - } \mu \mathsf { F }$ , 50-V Ceramic

Figure 26. Adjustable Output Voltage Typical Application

10.2.2.1 Design Requirements

Table 6 lists the design requirements for the adjustable output voltage application.

Table 6. Adjustable Output Voltage Application Parameters

PARAMETERSVALUE
Regulated output voltage, $V_{OUT}$ 20 V
Maximum input voltage, $V_{IN(max)}$ 28 V
Maximum load current, $I_{LOAD(max)}$ 1 A
Switching frequency, FFixed at a nominal 260 kHz

10.2.2.2 Detailed Design Procedure

10.2.2.2.1 Programming Output Voltage

For this application, TI recommends selecting $\mathsf { R } _ { 1 }$ and $\mathsf { R } _ { 2 } ,$ as shown in Parameter Measurement Information. Use Equation 3 to select the appropriate resistor values.

$$ V _ {O U T} = V _ {R E F} \left(1 + \frac {R _ {2}}{R _ {1}}\right) $$

$$ \begin{array}{l} \text {where} \ \bullet \quad V _ {\text {REF}} = 1. 2 1 \mathrm{V} \end{array}\tag{3} $$

Select a value for $\mathsf { R } _ { 1 }$ between 240 Ω and 1.5 kΩ. The lower resistor values minimize noise pickup in the sensitive feedback pin. For the lowest temperature coefficient and the best stability with time, use 1% metal film resistors as in Equation 4.

$$ R _ {2} = R _ {1} \left(\frac {V _ {\mathrm{OUT}}}{V _ {\mathrm{REF}}} - 1\right)\tag{4} $$

For this application example, select ${ \mathsf { R } } _ { 1 }$ to be 1 kΩ, 1%. Solve for ${ \sf R } _ { 2 }$ with Equation 5.

$$ R _ {2} = R _ {1} \left(\frac {V _ {\mathrm{OUT}}}{V _ {\mathrm{REF}}} - 1\right) = 1 \mathrm{k} \Omega \left(\frac {2 0 \mathrm{V}}{1 . 2 3 \mathrm{V}} - 1\right)\tag{5} $$

R = 1 kΩ (16.53 − 1) = 15.53 kΩ, closest 1% value is 15.4 kΩ.

$$ \mathsf {R} _ {2} = 1 5. 4 \mathrm{k} \Omega . $$

10.2.2.2.2 Inductor Selection (L1)

Calculate the inductor Volt × microsecond constant E × T $( \mathsf { V } \times \mathsf { \mu } \mathsf { s } )$ with Equation 6.

$$ E \cdot T = \left(V _ {I N (M A X)} - V _ {O U T} - V _ {S A T}\right) \cdot \frac {V _ {O U T} + V _ {D}}{V _ {I N (M A X)} - V _ {S A T} + V _ {D}} \cdot \frac {1 0 0 0}{2 6 0} (V \cdot \mu s) $$

where

• VSAT = internal switch saturation voltage = 0.25 V

• V = diode forward voltage drop = 0.5 V

(6)

For this application example, calculate the inductor Volt × microsecond constant (E × T) with Equation 7.

$$ \begin{array}{l} \mathrm{E} \cdot \mathrm{T} = (2 8 - 2 0 - 0. 2 5) \cdot \frac {2 0 + 0 . 5}{2 8 - 0 . 2 5 + 0 . 5} \cdot \frac {1 0 0 0}{2 6 0} (\mathrm{V} \cdot \mu \mathrm{s}) \ \mathrm{E} \cdot \mathrm{T} = (7. 7 5) \cdot \frac {2 0 . 5}{2 8 . 2 5} \cdot 3. 8 5 (\mathrm{V} \cdot \mu \mathrm{s}) = 2 1. 6 (\mathrm{V} \cdot \mu \mathrm{s}) \end{array}\tag{7} $$

Use the E × T value from the previous formula and match it with the E × T number on the vertical axis of the inductor value selection guide in Figure 27. E × T = 21.6 (V × μs).

On the horizontal axis, select the maximum load current $( \mathsf { I } _ { \mathsf { L O A D } } ( \mathsf { m a x } ) = 1 \ \mathsf { A } )$

Identify the inductance region intersected by the E × T value and the maximum load current value. Each region is identified by an inductance value and an inductor code (LXX). From the inductor value selection guide shown in Figure 27, the inductance region intersected by the 21.6 (V × μs) horizontal line and the 1-A vertical line is 68 μH, and the inductor code is L30.

Select an appropriate inductor from the four manufacturer's part numbers listed in Table 2. For information on the different types of inductors, see the inductor selection in the fixed output voltage design procedure. From the table in Table 2, locate line L30, and select an inductor part number from the list of manufacturers' part numbers.

10.2.2.2.3 Output Capacitor SeIection (C )

Select an output capacitor from the capacitor code selection guide in Table 7. Using the inductance value found in the inductor selection guide, step 1, locate the appropriate capacitor code corresponding to the desired outpu voltage. Use the appropriate row of the capacitor code selection guide, in Table 7. For this example, use the 15 to 20 V row. The capacitor code corresponding to an inductance of 68 μH is C20.

Table 7. Capacitor Code Selection Guide

CASE STYLE(1)OUTPUT VOLTAGE (V)INDUCTANCE (μH)
22334768100150220
SM and TH1.21 to 2.5————C1C2C3
SM and TH2.5 to 3.75———C1C2C3C3
SM and TH3.75 to 5——C4C5C6C6C6
SM and TH5 to 6.25—C4C7C6C6C6C6
SM and TH6.25 to 7.5C8C4C7C6C6C6C6
SM and TH7.5 to 10C9C10C11C12C13C13C13
SM and TH10 to 12.5C14C11C12C12C13C13C13
SM and TH12.5 to 15C15C16C17C17C17C17C17
SM and TH15 to 20C18C19C20C20C20C20C20
SM and TH20 to 30C21C22C22C22C22C22C22
TH30 to 37C23C24C24C25C25C25C25

(1) SM = surface mount, TH = through hole

Select an appropriate capacitor value and voltage rating, using the capacitor code, from the output capacitor selection table in Table 8. There are two solid tantalum (surface mount) capacitor manufacturers and four electrolytic (through hole) capacitor manufacturers to choose from. TI recommends that both the manufacturers and the manufacturer's series that are listed in the table be used. From the output capacitor selection table in Table 8, choose a capacitor value (and voltage rating) that intersects the capacitor code(s) selected in section A, C20 (Table 8).

The capacitance and voltage rating values corresponding to the capacitor code C20 are surface mount and through hole.

Surface mount:

• 33-μF, 25-V Sprague 594d series

• 33-μF, 25-V AVX TPS series

Through hole:

• 33-μF, 25-V Sanyo OS-CON SC series

• 120-μF, 35-V Sanyo MV-GX series

• 120-μF, 35-V Nichicon PL series

• 120-μF, 35-V Panasonic HFQ series

Other manufacturers or other types of capacitors may also be used, provided the capacitor specifications (especially the 100 kHz ESR) closely match the characteristics of the capacitors listed in the output capacitor table. Refer to the capacitor manufacturers' data sheet for this information.

Table 8. Output Capacitor Selection Table

OUTPUT CAPACITOR
CAP. REF. DESG.#SURFACE MOUNTTHROUGH HOLE
SPRAGUE 594D SERIES (μF/V)AVX TPSSERIES (μF/V)SANYO OS-CON SA SERIES (μF/V)SANYO MV-GX SERIES (μF/V)NICHICON PL SERIES (μF/V)PANASONIC HFQ SERIES (μF/V)
C1120/6.3100/10100/10220/35220/35220/35
C2120/6.3100/10100/10150/35150/35150/35
C3120/6.3100/10100/35120/35120/35120/35
C468/10100/1068/10220/35220/35220/35
C5100/16100/10100/10150/35150/35150/35
C6100/16100/10100/10120/35120/35120/35
C768/10100/1068/10150/35150/35150/35
C8100/16100/10100/10330/35330/35330/35
C9100/16100/16100/16330/35330/35330/35
C10100/16100/1668/16220/35220/35220/35
C11100/16100/1668/16150/35150/35150/35
C12100/16100/1668/16120/35120/35120/35
C13100/16100/16100/16120/35120/35120/35
C14100/16100/16100/16220/35220/35220/35
C1547/2068/2047/20220/35220/35220/35
C1647/2068/2047/20150/35150/35150/35
C1747/2068/2047/20120/35120/35120/35
C1868/25(2x) 33/25 $47/25^{(1)}$ 220/35220/35220/35
C1933/2533/25 $33/25^{(1)}$ 150/35150/35150/35
C2033/2533/25 $33/25^{(1)}$ 120/35120/35120/35
C2133/35(2x) 22/25 $See^{(2)}$ 150/35150/35150/35
C2233/3522/35 $See^{(2)}$ 120/35120/35120/35
C23 $See^{(2)}$ $See^{(2)}$ $See^{(2)}$ 220/50100/50120/50
C24 $See^{(2)}$ $See^{(2)}$ $See^{(2)}$ 150/50100/50120/50
C25 $See^{(2)}$ $See^{(2)}$ $See^{(2)}$ 150/5082/5082/50

(1) The SC series of Os-Con capacitors (others are SA series)
(2) The voltage ratings of the surface mount tantalum chip and Os-Con capacitors are too low to work at these voltages.

10.2.2.2.4 Catch Diode Selection (D1)

In normal operation, the average current of the catch diode is the load current times the catch diode duty cycle, 1-D (D is the switch duty cycle, which is approximately $\mathsf { V _ { O U T } } / \mathsf { V _ { I N } } )$ . The largest value of the catch diode average current occurs at the maximum input voltage (minimum D). For normal operation, the catch diode current rating must be at least 1.3 times greater than its maximum average current. However, if the power supply design must withstand a continuous output short, the diode must have a current rating greater than the maximum current limit of the LM2672. The most stressful condition for this diode is a shorted output condition. Refer to the table shown in Table 4. Schottky diodes provide the best performance, and in this example a 1-A, 40-V Schottky diode would be a good choice. If the circuit must withstand a continuous shorted output, a higher current (at least 2.2-A) Schottky diode is recommended.

The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best performance and efficiency. The Schottky diode must be placed close to the LM2672 using short leads and short printed circuit traces.

10.2.2.2.5 Input Capacitor $( \mathsf { C } _ { \mathsf { I N } } )$

A low ESR aluminum or tantalum bypass capacitor is required between the input pin and ground to prevent large voltage transients from appearing at the input. This capacitor must be placed close to the IC using short leads. In addition, the RMS current rating of the input capacitor must be selected to be at least ½ the DC load current. The capacitor manufacturer data sheet must be checked to assure that this current rating is not exceeded. Figure 21 shows typical RMS current ratings for several different aluminum electrolytic capacitor values. A parallel connection of two or more capacitors may be required to increase the total minimum RMS current rating to suit the application requirements.

For an aluminum electrolytic capacitor, the voltage rating must be at least 1.25 times the maximum input voltage. Caution must be exercised if solid tantalum capacitors are used. The tantalum capacitor voltage rating must be twice the maximum input voltage. The tables in Table 5 show the recommended application voltage for AVX TPS and Sprague 594D tantalum capacitors. It is also recommended that they be surge current tested by the manufacturer. The TPS series available from AVX, and the 593D and 594D series from Sprague are all surge current tested. Another approach to minimize the surge current stresses on the input capacitor is to add a small inductor in series with the input supply line.

Use caution when using ceramic capacitors for input bypassing, because it may cause severe ringing at the $V _ { \sf I N }$ pin.

The important parameters for the input capacitor are the input voltage rating and the RMS current rating. With a maximum input voltage of 28 V, an aluminum electrolytic capacitor with a voltage rating of at least 35 V (1.25 × $\mathsf { V } _ { \mathsf { I N } } )$ is required.

The RMS current rating requirement for the input capacitor in a buck regulator is approximately ½ the DC load current. In this example, with a 1-A load, a capacitor with a RMS current rating of at least 500 mA is required. The curves shown in Figure 21 can be used to select an appropriate input capacitor. From the curves, locate the 35-V line and note which capacitor values have RMS current ratings greater than 500 mA.

For a through hole design, a 330-μF, 35-V electrolytic capacitor (Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or equivalent) would be adequate. Other types or other manufacturers' capacitors can be used provided the RMS ripple current ratings are adequate. Additionally, for a complete surface mount design, electrolytic capacitors such as the Sanyo CV-C or CV-BS and the Nichicon WF or UR and the NIC Components NACZ series could be considered.

For surface mount designs, solid tantalum capacitors can be used, but caution must be exercised with regard to the capacitor surge current rating and voltage rating. In this example, checking Table 5, and the Sprague 594D series datasheet, a Sprague 594D 15-μF, 50-V capacitor is adequate.

10.2.2.2.6 Boost Capacitor (C )

This capacitor develops the necessary voltage to turn the switch gate on fully. All applications must use a 0.01-μF, 50-V ceramic capacitor. If the soft-start and frequency synchronization features are desired, see steps 6 and 7 in the fixed output design procedure.

10.2.2.3 Application Curve


Figure 27. LM2672, Adjustable Output

11 Power Supply Recommendations

The input voltage for the power supply is connected to the $V _ { \sf I N }$ pin. In addition to providing energy to the load the input voltage also provides bias for the internal circuitry of the LM2672. For ensured performance, the input voltage must be in the range of 6.5 V to 40 V. For best performance of the power supply, the $V _ { \sf I N }$ pin must always be bypassed with an input capacitor placed close to this pin and GND.

12 Layout

12.1 Layout Guidelines

Layout is very important in switching regulator designs. Rapidly switching currents associated with wiring inductance can generate voltage transients which can cause problems. For minimal inductance and ground loops, the wires indicated by heavy lines (in Figure 19) must be wide printed circuit traces and must be kept as short as possible. For best results, external components must be placed as close to the switcher IC as possible using ground plane construction or single point grounding.

This is the ground reference connection for all components in the power supply. In fast-switching, high-current applications such as those implemented with the LM2672, TI recommends that a broad ground plane be used to minimize signal coupling throughout the circuit.

If open-core inductors are used, take special care as to the location and positioning of this type of inductor. Allowing the inductor flux to intersect sensitive feedback, IC ground path, and ${ \mathsf { C } } _ { \mathsf { O U T } }$ wiring can cause problems.

When using the adjustable version, take special care as to the location of the feedback resistors and the associated wiring. Physically place both resistors near the IC, and route the wiring away from the inductor, especially an open core type of inductor.

12.1.1 WSON Package Devices

The LM2672 is offered in the 16-pin WSON surface mount package to allow for increased power dissipation compared to the 8-pin SOIC and PDIP.

The Die Attach Pad (DAP) can and must be connected to PCB Ground plane/island. For CAD and assembly guidelines, refer to AN-1187 Leadless Leadframe Package (LLP).

12.2 Layout Examples

$\mathsf { C } _ { \mathsf { I N } } = 1 5 \mathsf { - } \mathsf { \mu F } , 5 0 \mathsf { - } \mathsf { V } ,$ solid tantalum Sprague 594D series

COUT = 68-μF, 16-V, solid tantalum Sprague 594D series

D1 = 1-A, 40-V Schottky rectifier, surface mount

L1 = 33-μH, L23, coilcraft DO3316

$\mathsf { C } _ { \mathsf { B } } = 0 . 0 1 \mathsf { - \mu F }$ , 50-V ceramic

Figure 28. Typical Surface Mount PC Board Layout, Fixed Output

Layout Examples (continued)

C = 15-μF, 50-V, solid tantalum Sprague 594D series

C = 33-μF, 25-V, solid tantalum Sprague 594D series

D1 = 1-A, 40-V Schottky rectifier, surface mount

L1 = 68-μH, L30, coilcraft DO3316

$\mathsf { C } _ { \mathsf { B } } = 0 . 0 1 \mathsf { - } \mu \mathsf { F } ,$ , 50-V ceramic

R1 = 1k, 1%, R2: use formula in Detailed Design Procedure

Figure 29. Typical Surface Mount PC Board Layout, Adjustable Output

13 Device and Documentation Support

13.1 Documentation Support

13.1.1 Related Documentation

For related documentation see the following:

LM2670 SIMPLE SWITCHER® High Efficiency 3A Step-Down Voltage Regulator with Sync (SNVS036)

• AN-1187 Leadless Leadframe Package (LLP) (SNOA401)

13.2 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document.

13.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support.

13.4 Trademarks

E2E is a trademark of Texas Instruments.

SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.

All other trademarks are the property of their respective owners.

13.5 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.

13.6 Glossary

SLYZ022 — TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

14 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

14.1 DAP (WSON Package)

The die attach pad (DAP) must be connected to the PCB ground plane. For CAD and assembly guidelines, refer to AN-1187 Leadless Leadframe Package (LLP).

PACKAGING INFORMATION

Orderable part numberStatus(1)Material type(2)Package | PinsPackage qty | CarrierRoHS(3)Lead finish/ Ball material(4)MSL rating/ Peak reflow(5)Op temp (°C)Part marking(6)
LM2672LD-ADJ/NOPBActiveProductionWSON (NHN) | 161000 | SMALL T&RYesSNLevel-3-260C-168 HR-40 to 125S0004B
LM2672LD-ADJ/NOPB.BActiveProductionWSON (NHN) | 161000 | SMALL T&RYesSNLevel-3-260C-168 HR-40 to 125S0004B
LM2672M-12/NOPBActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672M-12
LM2672M-12/NOPB.BActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672M-12
LM2672M-3.3/NOPBActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672M3.3
LM2672M-3.3/NOPB.BActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672M3.3
LM2672M-5.0/NOPBActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672M5.0
LM2672M-5.0/NOPB.BActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672M5.0
LM2672M-ADJ/NOPBActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672MADJ
LM2672M-ADJ/NOPB.BActiveProductionSOIC (D) | 895 | TUBEYesSNLevel-1-260C-UNLIM-40 to 1252672MADJ
LM2672MX-12/NOPBActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672M-12
LM2672MX-12/NOPB.BActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672M-12
LM2672MX-3.3/NOPBActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672M3.3
LM2672MX-3.3/NOPB.BActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672M3.3
LM2672MX-5.0/NOPBActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672M5.0
LM2672MX-5.0/NOPB.BActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672M5.0
LM2672MX-ADJ/NOPBActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672MADJ
LM2672MX-ADJ/NOPB.BActiveProductionSOIC (D) | 82500 | LARGE T&RYesSNLevel-1-260C-UNLIM-40 to 1252672 MADJ
LM2672N-12/NOPBActiveProductionPDIP (P) | 840 | TUBEYesNIPDAULevel-1-NA-UNLIM-40 to 125LM2672 N-12
LM2672N-12/NOPB.BActiveProductionPDIP (P) | 840 | TUBEYesNIPDAULevel-1-NA-UNLIM-40 to 125LM2672 N-12
LM2672N-5.0/NOPBActiveProductionPDIP (P) | 840 | TUBEYesNIPDAULevel-1-NA-UNLIM-40 to 125LM2672 N-5.0
LM2672N-5.0/NOPB.BActiveProductionPDIP (P) | 840 | TUBEYesNIPDAULevel-1-NA-UNLIM-40 to 125LM2672 N-5.0
LM2672N-ADJ/NOPBActiveProductionPDIP (P) | 840 | TUBEYesNIPDAULevel-1-NA-UNLIM-40 to 125LM2672 N-ADJ
LM2672N-ADJ/NOPB.BActiveProductionPDIP (P) | 840 | TUBEYesNIPDAULevel-1-NA-UNLIM-40 to 125LM2672 N-ADJ

(1) Status: For more details on status, see our product life cycle.

(2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind.

(3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition.

(4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width.

(5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board.

(6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part.

www.ti.com

10-Nov-2025

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, an makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representativ and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS number

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

A0Dimension designed to accommodate the component width
B0Dimension designed to accommodate the component length
K0Dimension designed to accommodate the component thickness
WOverall width of the carrier tape
P1Pitch between successive cavity centers

Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE

*All dimensions are nomina

DevicePackage TypePackage DrawingPinsSPQReel Diameter (mm)Reel Width W1 (mm)A0 (mm)B0 (mm)K0 (mm)P1 (mm)W (mm)Pin1 Quadrant
LM2672LD-ADJ/NOPBWSONNHN161000177.812.45.35.31.38.012.0Q1
LM2672MX-12/NOPBSOICD82500330.012.46.55.42.08.012.0Q1
LM2672MX-3.3/NOPBSOICD82500330.012.46.55.42.08.012.0Q1
LM2672MX-5.0/NOPBSOICD82500330.012.46.55.42.08.012.0Q1
LM2672MX-ADJ/NOPBSOICD82500330.012.46.55.42.08.012.0Q1

*All dimensions are nominal

DevicePackage TypePackage DrawingPinsSPQLength (mm)Width (mm)Height (mm)
LM2672LD-ADJ/NOPBWSONNHN161000208.0191.035.0
LM2672MX-12/NOPBSOICD82500367.0367.035.0
LM2672MX-3.3/NOPBSOICD82500367.0367.035.0
LM2672MX-5.0/NOPBSOICD82500367.0367.035.0
LM2672MX-ADJ/NOPBSOICD82500367.0367.035.0

TUBE

B - Alignment groove width

*All dimensions are nominal

DevicePackage NamePackage TypePinsSPQL (mm)W (mm)T (μm)B (mm)
LM2672M-12/NOPBDSOIC895495840643.05
LM2672M-12/NOPB.BDSOIC895495840643.05
LM2672M-3.3/NOPBDSOIC895495840643.05
LM2672M-3.3/NOPB.BDSOIC895495840643.05
LM2672M-5.0/NOPBDSOIC895495840643.05
LM2672M-5.0/NOPB.BDSOIC895495840643.05
LM2672M-ADJ/NOPBDSOIC895495840643.05
LM2672M-ADJ/NOPB.BDSOIC895495840643.05
LM2672N-12/NOPBPPDIP84050214119384.32
LM2672N-12/NOPB.BPPDIP84050214119384.32
LM2672N-5.0/NOPBPPDIP84050214119384.32
LM2672N-5.0/NOPB.BPPDIP84050214119384.32
LM2672N-ADJ/NOPBPPDIP84050214119384.32
LM2672N-ADJ/NOPB.BPPDIP84050214119384.32


RECOMMENDED LAND PATTERN 1:1 RATIO WITH PKG SOLDER PADS

DIMENSIONS ARE IN MILLIMETERS


LDA16A (REV A)

SMALL OUTLINE INTEGRATED CIRCUIT

NOTES:

SMALL OUTLINE INTEGRATED CIRCUIT

NOTES: (continued)

  1. Publication IPC-7351 may have alternate designs.

  2. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

SMALL OUTLINE INTEGRATED CIRCUIT


SOLDER PASTE EXAMPLE BASED ON .005 INCH [0.125 MM] THICK STENCIL SCALE:8X

4214825/C 02/2019

NOTES: (continued)

  1. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations.

  2. Board assembly site may have different recommendations for stencil design.

P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE PACKAGE

NOTES: A. All linear dimensions are in inches (millimeters)
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001 variation BA.

Extracted Images

Figures and diagrams from the PDF

Preview the extracted datasheet assets and open any image in a separate tab for closer inspection.

7bcd6f9efcadf1f59532814e8de7839135f30a4e157e2203d14e63abf65c1a23.jpg

7bcd6f9efcadf1f59532814e8de7839135f30a4e157e2203d14e63abf65c1a23.jpg

70232c4076d422b24063f1dc0b3ebacf3898f21022381cb2c8c33f7a4094b9a5.jpg

70232c4076d422b24063f1dc0b3ebacf3898f21022381cb2c8c33f7a4094b9a5.jpg

d10b5c03b7e5f40f0e48d7a4bb80fe6f9943033b90643ae78bbe54892f60a62a.jpg

d10b5c03b7e5f40f0e48d7a4bb80fe6f9943033b90643ae78bbe54892f60a62a.jpg

d466ac6cc811b0ebff105e173195bf1a127ce85c67235b6b2b606ff69b2ad08e.jpg

d466ac6cc811b0ebff105e173195bf1a127ce85c67235b6b2b606ff69b2ad08e.jpg

7aad39e4981c26662d4bddee98f08ff3df90d7f9b4e47636803e56b8c5b90310.jpg

7aad39e4981c26662d4bddee98f08ff3df90d7f9b4e47636803e56b8c5b90310.jpg

57f4ee3d1945a7cb71b1b9f7a1b185a99cc3b933ed4656ab030d6e7de2555394.jpg

57f4ee3d1945a7cb71b1b9f7a1b185a99cc3b933ed4656ab030d6e7de2555394.jpg

5af7ca651ee540bbfb18b347d55ba10a407b83ebd9aa1e124337315cd6835743.jpg

5af7ca651ee540bbfb18b347d55ba10a407b83ebd9aa1e124337315cd6835743.jpg

0cb7cd5359dbe87a644dd5ac75f0023046b47024f53561d66ed8f142a20f68af.jpg

0cb7cd5359dbe87a644dd5ac75f0023046b47024f53561d66ed8f142a20f68af.jpg

f25dd9b18fb8b71407cbf112e1fdd9f683613b4513303bd457d1d71b64621a90.jpg

f25dd9b18fb8b71407cbf112e1fdd9f683613b4513303bd457d1d71b64621a90.jpg

d0ea548ea4ede924fe1385213c8ca01d55814bfd6cf220519ae9fca886f89cea.jpg

d0ea548ea4ede924fe1385213c8ca01d55814bfd6cf220519ae9fca886f89cea.jpg

72049adb405f51e7d6b0b78feab58b246f12cdfe95e9ad2b2d0ee057c7509032.jpg

72049adb405f51e7d6b0b78feab58b246f12cdfe95e9ad2b2d0ee057c7509032.jpg

24acdd95054477ff3e1c30d55d27c5d5115059719ed43abb8482f49d8a5fcac9.jpg

24acdd95054477ff3e1c30d55d27c5d5115059719ed43abb8482f49d8a5fcac9.jpg

33c59b9c26001e8f32e7306f236f5a0f339c698f123848c443b10ff6873c5d6b.jpg

33c59b9c26001e8f32e7306f236f5a0f339c698f123848c443b10ff6873c5d6b.jpg

3ba0ca334da2db6563508e3703b570137a42e6c5884f2f87f989c1a12675dfb0.jpg

3ba0ca334da2db6563508e3703b570137a42e6c5884f2f87f989c1a12675dfb0.jpg

dfa200b8bb820244dcc8511da25fc64d5c1d11e26833da370c4258a8cb417062.jpg

dfa200b8bb820244dcc8511da25fc64d5c1d11e26833da370c4258a8cb417062.jpg

8321b962b712bc0dc67461aed26c10f87bbfafbcff27b17c8c52618a6625400e.jpg

8321b962b712bc0dc67461aed26c10f87bbfafbcff27b17c8c52618a6625400e.jpg

4c4ea2aa3ab63922487893470ddd9d182795edb5e2de8c0e03fac237450b3f9c.jpg

4c4ea2aa3ab63922487893470ddd9d182795edb5e2de8c0e03fac237450b3f9c.jpg

586434fe6b6d0e35e0a79e710727d1ef3c5817cec5df3be21c5d15fbe2539bd7.jpg

586434fe6b6d0e35e0a79e710727d1ef3c5817cec5df3be21c5d15fbe2539bd7.jpg

66b41f40e9712f110f443fff90abc4960639295d33a7bc6d2f7a31399db516a7.jpg

66b41f40e9712f110f443fff90abc4960639295d33a7bc6d2f7a31399db516a7.jpg

1d46d72fb9d5cd538d52f2de2e9778b5b0ae70a30cfb035538462c5a59cdc2bd.jpg

1d46d72fb9d5cd538d52f2de2e9778b5b0ae70a30cfb035538462c5a59cdc2bd.jpg

b403eb91075fae7094750e669ae4638eb5c37e0beb586c81d3f630c84756c57d.jpg

b403eb91075fae7094750e669ae4638eb5c37e0beb586c81d3f630c84756c57d.jpg

708c1317a00e4ef11557fcc5a6bda04108a8e3d3071021c21759f9cd58fc89c5.jpg

708c1317a00e4ef11557fcc5a6bda04108a8e3d3071021c21759f9cd58fc89c5.jpg

eef5897a85161f7f56b0ddd3e5b41912f66c2a754d8b0b499e4466829feda6a7.jpg

eef5897a85161f7f56b0ddd3e5b41912f66c2a754d8b0b499e4466829feda6a7.jpg

192e00370aeb2e5d7e09b87d6f48e03cd432454a8b457d73587681bdfd4dc4d8.jpg

192e00370aeb2e5d7e09b87d6f48e03cd432454a8b457d73587681bdfd4dc4d8.jpg

f46f108087f5eeba3b2d68721590d158d294e34f06e906be08e3e3cdd2741b72.jpg

f46f108087f5eeba3b2d68721590d158d294e34f06e906be08e3e3cdd2741b72.jpg

a76d70f3c9e94ab8e829d63c4081b49cc30b953272bef1c3d992d159110e777d.jpg

a76d70f3c9e94ab8e829d63c4081b49cc30b953272bef1c3d992d159110e777d.jpg

07de827b24d2552a3cccfcaee5b8870712fe0b81436dc631b7a81a58527b9b47.jpg

07de827b24d2552a3cccfcaee5b8870712fe0b81436dc631b7a81a58527b9b47.jpg

fe79d654985b645d5147d0a07244b360b97a905122e6cb98984a2f23b9b63717.jpg

fe79d654985b645d5147d0a07244b360b97a905122e6cb98984a2f23b9b63717.jpg

22a6e107e8eac547852b824cfbb12771ad7e1816a5cde9a778eef3f07b1c8762.jpg

22a6e107e8eac547852b824cfbb12771ad7e1816a5cde9a778eef3f07b1c8762.jpg

b281dfb9845f13b4f455a708de892305ef89efe5a790bec6cdb62be3996c7f28.jpg

b281dfb9845f13b4f455a708de892305ef89efe5a790bec6cdb62be3996c7f28.jpg

5053117604b682813623001ebd47f797ffa65da0b835df2d1cce6883cf1f4f56.jpg

5053117604b682813623001ebd47f797ffa65da0b835df2d1cce6883cf1f4f56.jpg

64eaedc62b2825db89acdc6c97589227ce316e6d3f305d8ab190f59317033f6b.jpg

64eaedc62b2825db89acdc6c97589227ce316e6d3f305d8ab190f59317033f6b.jpg

c01477a14d50f229438166457b4c26520f86eebc81acf126c89c5cdec9a9bf01.jpg

c01477a14d50f229438166457b4c26520f86eebc81acf126c89c5cdec9a9bf01.jpg

c1dd25487b7e98f7e96b0ffe859ba40e1ded0605d79eefa8a7cb434d8888bf16.jpg

c1dd25487b7e98f7e96b0ffe859ba40e1ded0605d79eefa8a7cb434d8888bf16.jpg

4a24b97ca732157b6313b88836bfac3bc57502cae42d82f7b07abd0c7216b6af.jpg

4a24b97ca732157b6313b88836bfac3bc57502cae42d82f7b07abd0c7216b6af.jpg

6188a1a49c9a7f38b20f3d8628ca7a547d95a1b6b0dc4495fcdd186e37b3ae7b.jpg

6188a1a49c9a7f38b20f3d8628ca7a547d95a1b6b0dc4495fcdd186e37b3ae7b.jpg

bf8eb8cefe2fa8f9a02265e1fb8ffb6b9c8719c2d2c9e8868f74e0b9f9e7a3ba.jpg

bf8eb8cefe2fa8f9a02265e1fb8ffb6b9c8719c2d2c9e8868f74e0b9f9e7a3ba.jpg

2df225a7783e045b7a5c46f27321fa712e8f40f7b3a568961dc3b6f8c19ed4f1.jpg

2df225a7783e045b7a5c46f27321fa712e8f40f7b3a568961dc3b6f8c19ed4f1.jpg

032670129e979d298ea22d3e21a2b2a4f043dd30a44bc8733c5ad0f92addd972.jpg

032670129e979d298ea22d3e21a2b2a4f043dd30a44bc8733c5ad0f92addd972.jpg

28660d4d54ee7b5b01d44ca68d6d47c3705bd4e3d5c737b45ecfab806ab541cb.jpg

28660d4d54ee7b5b01d44ca68d6d47c3705bd4e3d5c737b45ecfab806ab541cb.jpg

4b8e5526e0750e2d17a63f3b1377ea5c2ec23797001682d99e0ca287b91bb03a.jpg

4b8e5526e0750e2d17a63f3b1377ea5c2ec23797001682d99e0ca287b91bb03a.jpg

d6d38eb033b6ae9598084ba65962aacb41c3a5b8a2fc99864ad5994fc33b0bc3.jpg

d6d38eb033b6ae9598084ba65962aacb41c3a5b8a2fc99864ad5994fc33b0bc3.jpg

c3ad6a2fb60ad0acaba15d04c313f74c73682200b1e52a26fd5009b0f7409ad8.jpg

c3ad6a2fb60ad0acaba15d04c313f74c73682200b1e52a26fd5009b0f7409ad8.jpg

fe3476c2f6ea00b8c7eb2348d924ecc4dcea13c5c44141f7ce5b16a426007cf2.jpg

fe3476c2f6ea00b8c7eb2348d924ecc4dcea13c5c44141f7ce5b16a426007cf2.jpg

4c10cb545f78a8905bf3c4fd8be863ed635c1736ebc3b0462a62b6d31c3d4666.jpg

4c10cb545f78a8905bf3c4fd8be863ed635c1736ebc3b0462a62b6d31c3d4666.jpg

1e2102108ce103cb5e62cc00d41e1fcebe512d6ad111963d968930ac642581a6.jpg

1e2102108ce103cb5e62cc00d41e1fcebe512d6ad111963d968930ac642581a6.jpg

9610b5d0d5f252fc8fc4739e9ba8ca17725a1d3d2b64ea44707ce70b03aeb07b.jpg

9610b5d0d5f252fc8fc4739e9ba8ca17725a1d3d2b64ea44707ce70b03aeb07b.jpg

ed2825033bc7ddbfde584489fbf8c9a5b0e73c7f4ed3914a43f8690c2fc8b9ef.jpg

ed2825033bc7ddbfde584489fbf8c9a5b0e73c7f4ed3914a43f8690c2fc8b9ef.jpg

f92486bfdaf20c9aaa9c04086bd5fc47d42b01159c86472afabe99dd33544e10.jpg

f92486bfdaf20c9aaa9c04086bd5fc47d42b01159c86472afabe99dd33544e10.jpg

5cade25ea4504d6e4306ae01caa832f398547cdd1d9608f86bb275cf639aa29b.jpg

5cade25ea4504d6e4306ae01caa832f398547cdd1d9608f86bb275cf639aa29b.jpg

3a1ecae7b53d42d4c3d1c4e088646bb873817b4ea7e7c5e85d98c14582758399.jpg

3a1ecae7b53d42d4c3d1c4e088646bb873817b4ea7e7c5e85d98c14582758399.jpg

72eff58c9bebf6ebbd2d74820a0c0db6bfe1d9e31d6732dc8825ac5b64cc3185.jpg

72eff58c9bebf6ebbd2d74820a0c0db6bfe1d9e31d6732dc8825ac5b64cc3185.jpg

906ed951f19526e19c91afad680b2c0611edcec66741eacdd4a857147e4d031b.jpg

906ed951f19526e19c91afad680b2c0611edcec66741eacdd4a857147e4d031b.jpg

0bcb4313b2e2d6c80b5eb442270b3733c8f7f20a83881368c5de99f33d74dfac.jpg

0bcb4313b2e2d6c80b5eb442270b3733c8f7f20a83881368c5de99f33d74dfac.jpg

24a1e7d4ba1aba4a7835fbd196b5ffbdc717738d998033b9c35c2426e26c9a98.jpg

24a1e7d4ba1aba4a7835fbd196b5ffbdc717738d998033b9c35c2426e26c9a98.jpg

a3dc0c5446dacd13462f8010bc29476c874e8c685bfcabc58166450426c7572b.jpg

a3dc0c5446dacd13462f8010bc29476c874e8c685bfcabc58166450426c7572b.jpg

da550c6751501811b834ee3e20e8d5c71a84733b45b7fa51e629d1aeff8d14e7.jpg

da550c6751501811b834ee3e20e8d5c71a84733b45b7fa51e629d1aeff8d14e7.jpg

df1d9de6135c03e3374d4827db63d1f42f8b7abc90998120f16513f5350a5d55.jpg

df1d9de6135c03e3374d4827db63d1f42f8b7abc90998120f16513f5350a5d55.jpg

dd88cd8f75ca7d56ca8e1397825b1f51079b287b80ab8875dba4246056bf1c5f.jpg

dd88cd8f75ca7d56ca8e1397825b1f51079b287b80ab8875dba4246056bf1c5f.jpg

8d1945bbe2ee81f3b074478419d1584334e75631e325855b159573e99962a107.jpg

8d1945bbe2ee81f3b074478419d1584334e75631e325855b159573e99962a107.jpg

Agent APIs

Use this datasheet from any agent

Send the page, markdown, chunks, or search endpoint to ChatGPT, Claude, embedr-app, or your own tooling.