Datasheet docs

Diodes Incorporated

PAM8610

10W-per-channel stereo Class-D audio amplifier with DC volume control, mute, fade, shutdown, and protection features.

Audio amplifier ICPAM8610TRPAM861040-pin QFN, 6mm × 6mmDifferential analog audioClass-D speaker outputGPIO

Description

The PAM8610 is a 10W (per channel) stereo Class-D audio amplifier with DC Volume Control which offers low THD+N (0.1%), low EMI, and good PSRR thus high-quality sound reproduction. The 32 steps DC volume control has a +32dB to -75dB range.

The PAM8610 runs off of a 7V to 15V supply at much higher efficiency than competitors’ ICs.

The PAM8610 only requires very few external components, significantly saving cost and board space.

The PAM8610 is available in a 40pin QFN 6mm*6mm package.

Features

10W @ 10%THD/Channel Output into a 8Ω Load at 13V

Low Noise: -90dB

• Over 90% Efficiency

• 32 Step DC Volume Control from -75dB to +32dB

• With Shutdown/Mute/Fade Function

• Over Current , Thermal and Short-Circuit Protection

• Low THD+N

• Low Quiescent Current

• Pop Noise Suppression

• Small Package Outlines: Thin 40-pin QFN 6mm*6mm Package

• Pb-Free Package (RoHS Complaint)

Pin Assignments

Applications

Flat Monitor /LCD TVS

Multi-Media Speaker System

DVD Players, Game Machines

• Boom Box

• Music Instruments

Typical Applications Circuit

Pin Descriptions

Pin NumberPin NameFunction
1RINNNegative differential audio input for right channel.
2RINPPositive differential audio input for right channel.
3AVDD5V Analog VDD
4VREFAnalog reference for gain control section.
5VOLUMEDC voltage that sets the gain of the amplifier.
6REF GNDGround for gain control circuitry. Connect to AGND. If using a DAC to control the volume, connect the DAC ground to this terminal.
7AGND1Analog GND
8FADEInput for controlling volume ramp rate when cycling SD or during power-up. A logic low on this pin places the amplifier in fade mode. A logic high on this pin allows a quick transition to the desired volume setting.
9LINPPositive differential audio input for left channel.
10LINNNegative differential audio input for left channel.
11, 20PGNDLPower ground for left channel H-bridge.
12, 19PVCCLPower supply for left channel H-bridge, not connected to PVCCR or AVCC.
13, 14LOUTNClass-D 1/2-H-bridge negative output for left channel.
15BSLNBootstrap I/O for left channel, negative high-side FET.
16BSLPBootstrap I/O for left channel, positive high-side FET.
17, 18LO UTPClass-D 1/2-H-bridge positive output for left channel.
21VCLAMPLInternally generated voltage supply for left channel bootstrap capacitors.
22CO SCI/O for charge/discharging currents onto capacitor for ramp generator triangle wave biased at V2P5.
23RO SCCurrent setting resistor for ramp generator. Nominally equal to 1/8*VCC.
24, 28AGNDAnalog GND
25MUTEA logic high on this pin disables the outputs and a logic low enables the outputs.
26AVCCHigh-voltage analog power supply (7V to 15V)
27V2P52.5V Reference for analog cells, as well as reference for unused audio input when using single-ended inputs.
29 $\overline{SD}$ Shutdown signal for IC (low = shutdown, high = operational). TTL logic levels with compliance to VCC.
30VCLAMPRInternally generated voltage supply for right channel bootstrap capacitors.
31, 40PGNDRPower ground for right channel H-bridge.
32, 39PVCCRPower supply for right channel H-bridge, not connected to PVCCL or AVCC.
33, 34ROUTPClass-D 1/2-H-bridge positive output for right channel.
35BSRPBootstrap I/O for right channel, positive high-side FET.
36BSRNBootstrap I/O for right channel, negative high-side FET.
37, 38ROUTNClass-D 1/2-H-bridge negative output for right channel.

Functional Block Diagram

Absolute Maximum Ratings $( \textcircled { \sc} \mathsf { T } _ { \mathsf { A } } = + 2 5 ^ { \circ } \mathsf { C } ,$ , unless otherwise specified.)

These are stress ratings only and functional operation is not implied. Exposure to absolute maximum ratings for prolonged time periods may affect device reliability. All voltages are with respect to ground.

ParameterRatingUnit
Supply Voltage $V_{DD}$ -0.3 to +16.5V
Input Voltage Range $V_I$ :
MUTE, $V_{REF}$ , VOLUME, $\overline{FADE}$ 0 to +6.0V
$\overline{SD}$ -0.3 to $V_{DD}$
RINN, RINP, LINN, LINP-0.3 to +6.0
Junction Temperature Range, $T_J$ -40 to +125°C
Storage Temperature-65 to +150
Lead Temperature 1, 6mm (1/16 inch)260, 5 sec

Recommended Operating Conditions $( \ @ \mathsf { T } _ { \mathsf { A } } = + 2 5 ^ { \circ } \mathsf { C } ,$ unless otherwise specified.)

ParameterRatingUnit
Supply Voltage (VDD)7 to 15V
Maximum Volume Control Pins, Input Pins Voltage0 to +5.0
High Level Input Voltage:
$\overline{SD}$ 2.0 to VDDV
MUTE, $\overline{FADE}$ 2.0 to 5.0
Low Level Input Voltage:
$\overline{SD}$ 0 to +0.3V
MUTE, $\overline{FADE}$ 0 to +0.3
Ambient Operating Temperature-20 to +85°C

Thermal Information

ParameterPackageSymbolMaxUnit
Thermal Resistance (Junction to Ambient)QFN6mm*6mm $\theta_{JA}$ 18.1°C/W
Thermal Resistance (Junction to Case)QFN6mm*6mm $\theta_{JC}$ 7.6

The Exposed PAD must be soldered to a thermal land on the PCB.

Electrical Characteristics (@ ${ \sf T } _ { \sf A } = + 2 5 ^ { \circ } { \sf C } ,$ VDD = 12V, RL = 8Ω, unless otherwise specified.)

ParameterSymbolTest ConditionsMinTypMaxUnits
Supply Voltage $V_{DD}$ 7.01215V
Continuous Output Power $P_O$ THD+N = 0.1%, f = 1kHz, $R_L$ = 8Ω5W
THD+N = 1.0%, f = 1kHz, $R_L$ = 8Ω8
THD+N = 10%, f = 1kHz, $R_L$ = 8Ω, $V_{DD}$ = 13V10
THD+N = 0.1%, f = 1kHz, $R_L$ = 4Ω (Note 3)15
Total Harmonic Distortion plus NoiseTHD+N $P_O$ = 5W, f = 1kHz, $R_L$ = 8Ω0.1%
Quiescent Current $I_{DD}$ No Load2030mA
Supply Quiescent Current in Shutdown Mode $I_{SD}$ Shutdown = 0V410μA
Drain-Source On-State Resistance $R_{DS(ON)}$ $V_{CC}$ = 12VIo = 1ATJ = +25°CHigh Side200mΩ
Low Side200
Total400
Power Supply Ripple RejectionPSRR1VPP Ripple, f = 1kHz,Inputs AC-Coupled to Ground-60dB
Oscillator Frequency $f_{OSC}$ $R_{OSC}$ = 120kΩ, $C_{OSC}$ = 220pF250kHz
Output Integrated Noise FloorVN20Hz to 22kHz, A-Weighting-90dB
CrosstalkCS $P_O$ = 3W, $R_L$ = 8Ω, f = 1kHz-80dB
Signal to Noise RatioSNRMaximum output at THD+N < 0.5%,f = 1kHz80dB
Output Offset Voltage(measured differentially)|Vos|INN and INP connected together30mV
2.5V Bias VoltageV2P5No Load2.5V
Internal Analog Supply VoltageAVDD $V_{DD}$ = 7V to 15V5.05.5V
Over Temperature ShutdownOTS150°C
Thermal HysteresisOTH40°C

Note: 3. Heat sink is required for high power output.

Typical Performance Characteristics (@TA = +25°C, VDD = 12V, RL = 8Ω, GV = 24dB, unless otherwise specified.)

  1. THD+N vs Frequency

  2. THD +N vs. Power

  3. THD+N vs Frequency (Po=1W)

  4. THD+N vs. Power

  5. THD+N vs Frequency (Po=3W)

Typical Performance Characteristics (cont.) (@TA = +25°C, VDD = 12V, RL = 4Ω, GV = 24dB, unless otherwise specified.)

  1. THD+N vs Frequency (Po=1W)

  1. THD+N vs Frequency (Po=3W)

Typical Performance Characteristics (cont.) (@TA = +25°C, VDD = 12V, RL = 8Ω, GV = 24dB, unless otherwise specified.)

  1. Noise Floor
  2. Power Supply Ripple Rejection

  1. Frequency Response (Vo=1.0Vrms)

  2. Efficiency vs Power

Typical Performance Characteristics (cont.) $( \ @ \mathsf { T } _ { \mathsf { A } } = + 2 5 ^ { \circ } \mathsf { C } ,$ , VDD = 12V, RL = 8Ω, GV = 24dB, unless otherwise specified.)

  1. Quesicent Current vs Supply Voltage

22.Power Dissipation vs. Output Power

Notes: PCB information for power dissipation measurement.

  1. The PCB size is 74mm 68mm with 1.2mm thickness, two layers and Fr4.
  2. 16 vias at the thermal land on the PCB with 0.5mm diameter.
  3. The size of exposed copper is 10mm*10mm with 3oz thickness.

Application Information

Test Setup for Performance Testing


Notes: 4. The AP AUX-0025 low pass filter is necessary for class-D amplifier measurement with AP analyzer.
5. Two 22μH inductors are used in series with load resistor to emulate the small speaker for efficiency measurement.

Power and Heat Dissipation

Choose speakers that are able to stand large output power from the PAM8610. Otherwise, speaker may suffer damage.

Heat dissipation is very important when the device works in full power operation. Two factors affect the heat dissipation, the efficiency of the device that determines the dissipation power, and the thermal resistance of the package that determines the heat dissipation capability.

In operation, some of power is dissipated to the resistors.

Power Dissipation: $\mathsf { P _ { L O S S } } = ( \mathsf { P o } ^ { \star } ( 1 \mathsf { - } \mathsf { \eta } / \mathsf { \eta } ) ^ { \star } 2$

The PAM8610’s efficiency is 90% with 10W ouput and 8Ω load. The dissipation power is 2.22W.

Thermal resistance of junction to ambient of the QFN package is 18.1°C/W and the junction temperature ${ \sf T } _ { \mathsf { J } } = { \sf P } _ { \mathsf { L O S S } } \ ^ { \star } \ { \theta } _ { \mathsf { J A } ^ { \star } } { \sf T } _ { \mathsf { A } } ,$ where ${ \mathsf T } _ { \mathsf A }$ is ambient temperature. If the ambient temperature is +85°C, the QFN’s junction temperature

$$ T _ {J} = 2. 2 2 ^ {*} 1 8. 1 + 8 5 = + 1 2 5 ^ {\circ} C $$

which is lower than $+ 1 5 0 ^ { \circ } \mathrm { C }$ rated junction temperature.

If the rated workable junction temperature is 150°C, the relat ionship between ambient temperature and permitted PLOSS is shown in below diagram.

From the diagram, it can be found that when the device works at 10W/8Ω load the dissipation power is 1.1W per channel, 2.2W total, the permitted ambient temperature is over $1 0 0 ^ { \circ } \mathsf { C } .$ . This is proven by actual test. The PAM8610 can work in full output power under +85°C ambient temperature.

Application Information (cont.)

Heat Dissipation in PCB Design

Generally, class-D amplifiers are high efficiency and need no heat sink. For high power ones that has high dissipation power, the heat sink may also not necessary if the PCB is carefully designed to achieve good heat by the PCB itself.

Dual-Side PCB

To achieve good heat, the PCB’s copper plate should be thicker than 0.035mm and both sides of the PCB should be utilized for heat sink.

The thermal pad on the bottom of the device should be soldered to the plate of the PCB, and via holes, usually 9 to 16, should be drilled in the PCB area under the device and deposited copper on the vias should be thick enough so that the heat can be dissipated to the other side of the plate. There should be no insulation mask on the other side of the copper plate. It is better to drill more vias around the device if possible.

4-Layer PCB

If it is 4-layer PCB, the two middle layers of grounding and power can be employed for heat dissipation, isolating them into serval islands to avoid short between ground and power.

Consideration for EMI

Filters are not required if the traces from the amplifier to the speakers are short (<20cm). But most applications require a ferrite bead filter as shown in below figure. The ferrite bead filter reduces EMI of around 1MHz and higher to meet the FCC and CE's requirements. It is recommended to use a ferrite bead with very low impedances at low f requenc ies and high impedance at high frequencies (above 1MHz).

The EMI characteristics are as follows after employing the ferrite bead. Vertical Polarization

Horizontal Polarization

Application Information (cont.)

Volume Control

A DC volume control section is integrated in PAM8610, controlling via VREF, VOLUME and VREFGND terminals. The voltage on VOLUME pin, without exceeding VREF, determines internal amplifier gain as listed in Table 1.

If a resistor divider is used to fix gain of the amplifier, the VREF terminal can be directly connected to AVDD and the resistor divider connected across VREF and REFGND. For fixed gain, the resistor divider values are to center the voltage given in the Table 1.

FADE Operation

The FADE terminal is a logic input that controls the operation of the volume control circuitry during transitions to and from the shutdown state and during power-up.

A logic low on this terminal will set the amplifier in fade mode. During power-up or recovery from the shutdown state (a logic high is applied to the SD terminal), the volume is smoothly ramped up from the mute state, -75dB, to the desired volume set by the voltage on the volume control terminal. Conversely, the volume is smoothly ramped down from the current state to the mute state when a logic low is applied to the SD terminal. A logic high on this pin disables the volume fade effect during transitions to and from the shutdown state and during power-up. During power-up or recovery from the shutdown state (a logic high is applied to the SD terminal), the transition from the mute state, -75dB, to the desired volume setting is less than 1ms. Conversely, the volume ramps down from current state to the mute state within 1ms when a logic low is applied to the SD terminal.

MUTE Operation

The MUTE pin is an input for controlling the output state of the PAM8610. A logic high on this pin disables the outputs and low enables the outputs. This pin may be used as a quick disable or enable of the outputs without a volume fade.

For power saving, the SD pin should be used to reduce the quiescent current to the absolute minimum level. The volume will fade, increasing or decreasing slowly, when leaving or entering the shutdown state if the FADE terminal is held low. If the FADE terminal is held high, the outputs will transit very quickly. Refer to the FADE operation section. 1

Shutdown Operation

The PAM8610 employs a shutdown operation mode to reduce supply current to the absolute minimum level during periods of non-use to save power. The SD input terminal should be held high during normal operation when the amplifier is in use. Pulling SD low causes the outputs to mute and the amplifier to enter a low-current state. SD should never be left unconnected to prevent the amplifier from unpredictable operation.

For the best power-off pop performance, the amplifier should be set in shutdown mode prior to removing the power supply voltage.

Internal 2.5V Bias Generator Capacitor Selection

The internal 2.5V bias generator (V2P5) provides the internal bias for the preamplifier stage. The external input capacitors and this internal reference allow the inputs to be biased within the optimal common-mode range of the input preamplifiers.

The selection of the capacitor value on the V2P5 terminal is critical for achieving the best device performance. During startup or recovery from shutdown state, the V2P5 capacitor determines the rate at which the amplifier starts up. When the voltage on the V2P5 capacitor equals 0.75 x V2P5, or 75% of its final value, the device turns on and the Class-D outputs start switching. The startup time is not critical for the best de-pop performance since any heard pop sound is the result of the Class-D output switching-on other than that of the startup time. However, at least a 0.47μF capacitor is recommended for the V2P5 capacitor.

Another function of the V2P5 capacitor is to filter high frequency noise on the internal 2.5V bias generator.

Power Supply Decoupling, CS

The PAM8610 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) as low as possible. Power supply decoupling also prevents oscillations caused by long lead between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-seriesresistance (ESR) ceramic capacitor, typically 1μF, is recommended, placing as close as possible to the device’s VCC lead. To filter lower-frequency noises, a large aluminum electrolytic capacitor of 10μF or greater is recommended, placing near the audio power amplifier. The 10μF capacitor also serves as a loca storage capacitor for supplying current during large signal transients on the amplifier outputs.

Application Information (cont.)

Selection of COSC and ROSC

The switching frequency is determined by the values of components connected to ROSC (pin 23) and COSC (pin 22) and calculated as follows:

$$ f _ {\mathrm{osc}} = 2 \pi / (R _ {\mathrm{osc}} ^ {*} C _ {\mathrm{osc}}) $$

The frequency may varies from 225kHz to 275kHz by adjusting the values of ROSC and COSC. The recommended values are COSC = 220pF, ROSC = 120kΩ for a switching frequency of 250kHz.

BSN and BSP Capacitors

The full H-bridge output stages use NMOS transistors only. They therefore require bootstrap capacitors for the high side of each output to turn on correctly. At least 220nF ceramic capacitor, rated for at least 25V, must be connected from each output to its corresponding bootstrap input Specifically, one 220nF capacitor must be connected from xOUTP to xBSP, and another 220nF capacitor from xOUTN to xBSN. It is recommended to use 1µF BST capacitor to replace 220nF (pin15, pin 16, pin 35 and pin 36) for lower than 100Hz applications.

VCLAMP Capacitors

To ensure that the maximum gate-to-source voltage for the NMOS output transistors not exceeded, two internal regulators are used to clamp the gate voltage. Two 1μF capacitors must be connected from VCLAMPL and VCLAMPR to ground and must be rated for at least 25V. The voltages at the VCLAMP terminals vary with VCC and may not be used to power any other circuitry.

Internal Regulated 5-V Supply (AVDD)

The AVDD terminal is the output of an internally generated 5V supply, used for the oscillator, preamplifier, and volume control circuitry. It requires a 0.1μF to 1μF capacitor, placed very close to the pin to ground to keep the regulator stable. The regulator may not be used to power any external circuitry.

Differential Input

The differential input stage of the amplifier eliminates noises that appear on the two input lines of the channel. To use the PAM8610 with a differential source, connect the positive lead of the audio source to the INP input and the negative lead from the audio source to the INN input. To use the PAM8610 with a single-ended source, acground the INP input through a capacitor equal in value to the input capacitor on INN and apply the audio source to the INN input. In a single-ended input application, the INP input should be acgrounded at the audio source other than at the device input for best noise performance.

Using Low-ESR Capacitors

Low- ESR capacitors are recommended throughout this application section. A real (with respect to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance the more the real capacitor behaves as an ideal capacitor.

Short-Circuit Protection

The PAM8610 has short circuit protection circuitry on the outputs to prevent damage to the device when output-to-output shorts, output-to-GND shorts, or output-to-VCC shorts occur. Once a short-circuit is detected on the outputs, the output drive is immediately disabled. This is a latched fault and must be reset by cycling the voltage on SD the pin to a logic low and back to the logic high state for normal operation. This will clear the short-circuit flag and allow for normal operation if the short was removed. If the short was not removed, the protection circuitry will again activate.

Thermal Protection

Thermal protection on the PAM8610 prevents damage to the device when the internal die temperature exceeds +150°C. There is a ±15 degree tolerance on this trip point from device to device. Once the die temperature exceeds the set thermal point, the device enters into the shutdown state and the outputs are disabled. This is not a latched fault. The thermal fault is cleared once the temperature of the die is reduced by 40°C. The device begins normal operation at this point without external system intervention.

Ordering Information

Part NumberPart MarkingPackage TypeStandard Package
PAM8610TRPAM8610XATYWWLLQFN6x6-402500 Units/Tape&amp;Reel

Marking Information

Package Outline Dimensions (All dimensions in mm.)

QFN6x6-40


BUT WITH DIFFERENT THICKNESS

AMAX.0.800
NOM.0.750
MIN.0.700

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks.

final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

  1. are intended to implant into the body, or

  2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2020, Diodes Incorporated

www.diodes.com

Extracted Images

Figures and diagrams from the PDF

Preview the extracted datasheet assets and open any image in a separate tab for closer inspection.

Extracted datasheet image d6dc9bb1db8e173df3f082cfcd53f5897e6604bf4caa0aff1727be6cb2d9d088.jpg.

Extracted datasheet image d6dc9bb1db8e173df3f082cfcd53f5897e6604bf4caa0aff1727be6cb2d9d088.jpg.

Extracted datasheet image bd0b4b1b122666e8d9f39b82074222cb51bd3615536f858ae0bb8c5846ab286c.jpg.

Extracted datasheet image bd0b4b1b122666e8d9f39b82074222cb51bd3615536f858ae0bb8c5846ab286c.jpg.

Extracted datasheet image 2b79a8b40d58e689b0cf3adf012a85152ec7fa0d1fe34d21387c0b9adb8244e7.jpg.

Extracted datasheet image 2b79a8b40d58e689b0cf3adf012a85152ec7fa0d1fe34d21387c0b9adb8244e7.jpg.

Extracted datasheet image 7e00ce3aef0f3f73db9ba85984577fd905876f5cfce3a02f141e8bd0cda5971b.jpg.

Extracted datasheet image 7e00ce3aef0f3f73db9ba85984577fd905876f5cfce3a02f141e8bd0cda5971b.jpg.

Extracted datasheet image 924be867349130a2176221921847f5896114f0e46ecc49407e069090369d3d18.jpg.

Extracted datasheet image 924be867349130a2176221921847f5896114f0e46ecc49407e069090369d3d18.jpg.

Extracted datasheet image f6436cb72130be860aaad88af2ef5de497ff43227da7db4330c829fae21af7bd.jpg.

Extracted datasheet image f6436cb72130be860aaad88af2ef5de497ff43227da7db4330c829fae21af7bd.jpg.

Electrical characteristics table

Electrical characteristics table

PCB thermal-via and plane layout illustration

PCB thermal-via and plane layout illustration

PAM8610 application schematic

PAM8610 application schematic

PAM8610 package ordering code explanation

PAM8610 package ordering code explanation

THD+N versus frequency graph

THD+N versus frequency graph

Oscillator frequency formula

Oscillator frequency formula

Extracted datasheet image fbe963851c25c894f061dbc1a2bc923f8d748c9858a47f8571afe25b1c0bf74f.jpg.

Extracted datasheet image fbe963851c25c894f061dbc1a2bc923f8d748c9858a47f8571afe25b1c0bf74f.jpg.

Extracted datasheet image f7edd606d7e501b9cca6b5f19a76dc6d92bc9ac13bfc2922bfb489f0cccc093b.jpg.

Extracted datasheet image f7edd606d7e501b9cca6b5f19a76dc6d92bc9ac13bfc2922bfb489f0cccc093b.jpg.

Extracted datasheet image ae672fb366e5884aa60698a8e98c7ef5f74eb3cc8b5d7169ca9219c824420b11.jpg.

Extracted datasheet image ae672fb366e5884aa60698a8e98c7ef5f74eb3cc8b5d7169ca9219c824420b11.jpg.

Extracted datasheet image a6f685bf8e1ac0c0a17bdea48cc7bda9c131ea03e897e939a30f04fb162c7161.jpg.

Extracted datasheet image a6f685bf8e1ac0c0a17bdea48cc7bda9c131ea03e897e939a30f04fb162c7161.jpg.

Extracted datasheet image 817b24064a5cf0d6d8bff8d3f82d6f3b8cebdbcba6d39da8cdd06bb2e521002a.jpg.

Extracted datasheet image 817b24064a5cf0d6d8bff8d3f82d6f3b8cebdbcba6d39da8cdd06bb2e521002a.jpg.

Extracted datasheet image f458ab92b557f58aaf435b585e79ed56620d0390b0e44ef49baf53470127a6bf.jpg.

Extracted datasheet image f458ab92b557f58aaf435b585e79ed56620d0390b0e44ef49baf53470127a6bf.jpg.

Absolute maximum ratings table

Absolute maximum ratings table

Partial document crop with review watermark

Partial document crop with review watermark

Frequency response versus frequency for different voltage gains

Frequency response versus frequency for different voltage gains

THD+N versus output power at multiple supply voltages

THD+N versus output power at multiple supply voltages

Crosstalk versus frequency

Crosstalk versus frequency

Frequency response for different voltage gains

Frequency response for different voltage gains

Thermal resistance specifications for QFN6mm*6mm package

Thermal resistance specifications for QFN6mm*6mm package

PCB thermal-via and power-area layout illustration

PCB thermal-via and power-area layout illustration

THD+N versus power at multiple voltage gains

THD+N versus power at multiple voltage gains

PCB thermal pad and thermal-via layout

PCB thermal pad and thermal-via layout

CMRR versus frequency

CMRR versus frequency

Frequency response magnitude plot

Frequency response magnitude plot

Output power versus supply voltage

Output power versus supply voltage

Frequency response graph at multiple frequencies

Frequency response graph at multiple frequencies

FCC Class B radiated emissions, vertical polarity

FCC Class B radiated emissions, vertical polarity

Power dissipation versus output power

Power dissipation versus output power

QFN package top-view mechanical drawing

QFN package top-view mechanical drawing

FCC Class B radiated emissions, horizontal polarity

FCC Class B radiated emissions, horizontal polarity

Electrical ratings and operating conditions table

Electrical ratings and operating conditions table

PAM8610 40-pin QFN top-view pinout

PAM8610 40-pin QFN top-view pinout

PAM8610 internal functional block diagram

PAM8610 internal functional block diagram

Partial diagonal watermark text

Partial diagonal watermark text

Distortion versus frequency graph at multiple output powers

Distortion versus frequency graph at multiple output powers

Ferrite bead and 200 pF speaker output filter

Ferrite bead and 200 pF speaker output filter

Frequency response graph showing dB versus Hz

Frequency response graph showing dB versus Hz

Junction temperature calculation

Junction temperature calculation

Frequency response graph showing dBV versus Hz

Frequency response graph showing dBV versus Hz

Package side-view mechanical drawing

Package side-view mechanical drawing

Distortion versus frequency graph for multiple gains

Distortion versus frequency graph for multiple gains

Distortion versus frequency graph at multiple supply voltages

Distortion versus frequency graph at multiple supply voltages

Part number, marking, package, and standard package information

Part number, marking, package, and standard package information

Power dissipation versus ambient temperature graph

Power dissipation versus ambient temperature graph

Agent APIs

Use this datasheet from any agent

Send the page, markdown, chunks, or search endpoint to ChatGPT, Claude, embedr-app, or your own tooling.