Datasheet docs

{ "name": "Analog Devices", "mpn": "ADF4351BCPZ-RL7" }

Analog Devices ADF4351BCPZ-RL7 Wideband RF Synthesizer

35 MHz to 4.4 GHz fractional-N/integer-N PLL frequency synthesizer with integrated VCO in a 32-lead CP-32-27 LFCSP package.

Communication

Data Sheet

ADF4351

FEATURES

Output frequency range: 35 MHz to 4400 MHz Fractional-N synthesizer and integer-N synthesizer Low phase noise VCO Programmable divide-by-1/-2/-4/-8/-16/-32/-64 output Typical jitter: 0.3 ps rms Typical EVM at 2.1 GHz: 0.4% Power supply: 3.0 V to 3.6 V Logic compatibility: 1.8 V Programmable dual-modulus prescaler of 4/5 or 8/9 Programmable output power level RF output mute function 3-wire serial interface Analog and digital lock detect Switched bandwidth fast lock mode Cycle slip reduction

APPLICATIONS

Wireless infrastructure (W-CDMA, TD-SCDMA, WiMAX, GSM, PCS, DCS, DECT) Test equipment Wireless LANs, CATV equipment Clock generation

GENERAL DESCRIPTION

The ADF4351 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and external reference frequency.

The ADF4351 has an integrated voltage controlled oscillator (VCO) with a fundamental output frequency ranging from 2200 MHz to 4400 MHz. In addition, divide-by-1/-2/-4/-8/-16/-32/-64 circuits allow the user to generate RF output frequencies as low as 35 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable. An auxiliary RF output is also available, which can be powered down when not in use.

Control of all on-chip registers is through a simple 3-wire interface. The device operates with a power supply ranging from 3.0 V to 3.6 V and can be powered down when not in use.

FUNCTIONAL BLOCK DIAGRAM

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2012–2017 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com

TABLE OF CONTENTS

Features .... 1
Applications.... 1
General Description .... 1
Functional Block Diagram .... 1
Revision History .... 2
Specifications.... 3
Timing Characteristics .... 5
Absolute Maximum Ratings.... 6
Transistor Count.... 6
Thermal Resistance .... 6
ESD Caution.... 6
Pin Configuration and Function Descriptions.... 7
Typical Performance Characteristics .... 9
Circuit Description.... 11
Reference Input Section.... 11
RF N Divider.... 11
Phase Frequency Detector (PFD) and Charge Pump.... 11
MUXOUT and Lock Detect.... 12
Input Shift Registers.... 12
Program Modes .... 12
VCO.... 12
Output Stage.... 13
Register Maps.... 14
Register 0.... 18

REVISION HISTORY

5/2012—Revision 0: Initial Version

1/2017—Rev. 0 to Rev. A
Changed CP-32-2 to CP-32-7....Throughout
Change to Figure 3....7
Updated Outline Dimension....28
Changes to Ordering Guide....28

Register 1....18
Register 2....18
Register 3....19
Register 4....20
Register 5....20
Register Initialization Sequence....20
RF Synthesizer—A Worked Example....21
Reference Doubler and Reference Divider....21
12-Bit Programmable Modulus....21
Cycle Slip Reduction for Faster Lock Times....22
Spurious Optimization and Fast Lock....22
Fast Lock Timer and Register Sequences....22
Fast Lock Example....22
Fast Lock Loop Filter Topology....23
Spur Mechanisms....23
Spur Consistency and Fractional Spur Optimization....24
Phase Resync....24
Applications Information....25
Direct Conversion Modulator....25
Interfacing to the ADuC70xx and the ADSP-BF527....26
PCB Design Guidelines for a Chip Scale Package....26
Output Matching....27
Outline Dimensions....28
Ordering Guide....28

SPECIFICATIONS

$\mathrm { A V _ { D D } = D V _ { D D } = V _ { V C O } = S D V _ { D D } = V _ { P } = 3 . 3 \ V \pm 1 0 ^ { 9 } \omega ; A G N D = D G N D = 0 \ V ; T _ { A } = T _ { A I N } = T _ { A N } = 0 . 3 4 4 w / k W }$ to TMAX, unless otherwise noted. Operating temperature range is $- 4 0 ^ { \circ } \mathrm { C } \mathrm { t o } + 8 5 ^ { \circ } \mathrm { C } .$

Table 1.

ParameterMinTypMaxUnitTest Conditions/Comments
$REF_{IN} CHARACTERISTICS$
Input Frequency10250MHzFor f < 10 MHz, ensure slew rate > 21 V/μs
Input Sensitivity0.7 $AV_{DD}$ V p-pBiased at $AV_{DD}/2$ ; ac coupling ensures $AV_{DD}/2$ bias
Input Capacitance10pF
Input Current±60μA
PHASE FREQUENCY DETECTOR (PFD)
Phase Detector Frequency32MHzFractional-N
45MHzInteger-N (band select enabled)
90MHzInteger-N (band select disabled)
CHARGE PUMP
$I_{CP} Sink/Source^1$ $R_{SET}=5.1 kΩ$
High Value5mA
Low Value0.312mA
$R_{SET} Range$ 3.910kΩ
Sink and Source Current Matching2%0.5 V ≤ $V_{CP}$ ≤ 2.5 V
$I_{CP} vs. V_{CP}$ 1.5%0.5 V ≤ $V_{CP}$ ≤ 2.5 V
$I_{CP} vs. Temperature$ 2% $V_{CP}=2.0 V$
LOGIC INPUTS
Input High Voltage, $V_{INH}$ 1.5V
Input Low Voltage, $V_{INL}$ 0.6V
Input Current, $I_{INH}/I_{INL}$ ±1μA
Input Capacitance, $C_{IN}$ 3.0pF
LOGIC OUTPUTS
Output High Voltage, $V_{OH}$ $DV_{DD}-0.4$ VCMOS output selected
Output High Current, $I_{OH}$ 500μA
Output Low Voltage, $V_{OL}$ 0.4V $I_{OL}=500 μA$
POWER SUPPLIES
$AV_{DD}$ 3.03.6V
$DV_{DD}, V_{VCO}, SDV_{DD}, V_P$ $AV_{DD}$ These voltages must equal $AV_{DD}$
$DI_{DD}+AI_{DD}^2$ 2127mA
Output Dividers6 to 36mAEach output divide-by-2 consumes 6 mA
$I_{VCO}^2$ 7080mA
$I_{RFOUT}^2$ 2126mARF output stage is programmable
Low Power Sleep Mode710μA
RF OUTPUT CHARACTERISTICS
VCO Output Frequency22004400MHzFundamental VCO mode
Minimum VCO Output Frequency Using Dividers34.375MHz2200 MHz fundamental output and divide-by-64 selected
VCO Sensitivity, $K_V$ 40MHz/V
Frequency Pushing (Open-Loop)1MHz/V
Frequency Pulling (Open-Loop)90kHzInto 2.00 VSWR load
Harmonic Content (Second)-19dBcFundamental VCO output
-20dBcDivided VCO output
Harmonic Content (Third)-13dBcFundamental VCO output
-10dBcDivided VCO output
Minimum RF Output Power3-4dBmProgrammable in 3 dB steps
Maximum RF Output Power35dBm
Output Power Variation±1dB
Minimum VCO Tuning Voltage0.5V
Maximum VCO Tuning Voltage2.5V
NOISE CHARACTERISTICS
VCO Phase Noise PerformanceVCO noise is measured in open-loop conditions
-89dBc/Hz10 kHz offset from 2.2 GHz carrier
-114dBc/Hz100 kHz offset from 2.2 GHz carrier
-134dBc/Hz1 MHz offset from 2.2 GHz carrier
-148dBc/Hz5 MHz offset from 2.2 GHz carrier
-86dBc/Hz10 kHz offset from 3.3 GHz carrier
-111dBc/Hz100 kHz offset from 3.3 GHz carrier
-134dBc/Hz1 MHz offset from 3.3 GHz carrier
-145dBc/Hz5 MHz offset from 3.3 GHz carrier
-83dBc/Hz10 kHz offset from 4.4 GHz carrier
-110dBc/Hz100 kHz offset from 4.4 GHz carrier
-131dBc/Hz1 MHz offset from 4.4 GHz carrier
-145dBc/Hz5 MHz offset from 4.4 GHz carrier
Normalized Phase Noise Floor (PNSYNTH)4PLL loop BW = 500 kHz
-220dBc/HzABP = 6 ns
-221dBc/HzABP = 3 ns
Normalized 1/f Noise (PN1_f)510 kHz offset; normalized to 1 GHz
-116dBc/HzABP = 6 ns
-118dBc/HzABP = 3 ns
In-Band Phase Noise-100dBc/Hz3 kHz from 2111.28 MHz carrier
Integrated RMS Jitter60.27ps
Spurious Signals Due to PFD Frequency-80dBc
Level of Signal with RF Mute Enabled-40dBm

1 ICP is internally modified to maintain constant loop gain over the frequency range.
2 TA = 25°C; AVDD = DVDD = VVCO = 3.3 V; prescaler = 8/9; fREFIN = 100 MHz; fPFD = 25 MHz; fRF = 4.4 GHz.
3 Using 50 Ω resistors to V , into a 50 Ω load. Power measured with auxiliary RF output disabled. The current consumption of the auxiliary output is the same as for the main output.
4 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 log N (where N is the N divide value) and 10 log fPFD. To calculate in-band phase noise performance as seen at the VCO output, use the following formula: $P N _ { S Y N T H } = \overline { { P } } N _ { T O T } - 1 0 \log ( f _ { P F D } ) - 2 0 \log N .$
5 The PLL phase noise is composed of flicker (1/f) noise plus the normalized PLL noise floor. The formula for calculating the 1/f noise contribution at an RF frequency (fRF) and at a frequency offset (f) is given by PN = PN1_f+ 10 log(10 kHz/f) + 20 log(fRF/1 GHz). Both the normalized phase noise floor and flicker noise are modeled in ADIsimPLL.

TIMING CHARACTERISTICS

$\mathrm A V _ { D D } = D V _ { D D } = V _ { V C O } = S D V _ { D D } = V _ { P } = 3 . 3 \ V \pm 1 0 ^ { 9 } 0 ; A G N D = D G N D = 0 \ V _ { D } = 3 . 3 6 V = 1 \frac { 1 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } . 3 6 V = 1 \frac { 3 } { 3 } \Omega = 0 . 3 5 6 \Omega / s$ 1.8 V and 3 V logic levels used; $\mathrm { T _ { A } } = \mathrm { T _ { M I N } }$ to $\mathrm { T _ { M A X } } ,$ unless otherwise noted.

Table 2.

ParameterLimitUnitDescription
$t_1$ 20ns minLE setup time
$t_2$ 10ns minDATA to CLK setup time
$t_3$ 10ns minDATA to CLK hold time
$t_4$ 25ns minCLK high duration
$t_5$ 25ns minCLK low duration
$t_6$ 10ns minCLK to LE setup time
$t_7$ 20ns minLE pulse width

Timing Diagram


Figure 2. Timing Diagram

ABSOLUTE MAXIMUM RATINGS

$\mathrm { T _ { A } } = 2 5 ^ { \circ } \mathrm { C } ,$ unless otherwise noted.

Table 3.

ParameterRating
$AV_{DD}\ to\ GND^1$ -0.3 V to +3.9 V
$AV_{DD}\ to\ DV_{DD}$ -0.3 V to +0.3 V
$V_{VCO}\ to\ GND^1$ -0.3 V to +3.9 V
$V_{VCO}\ to\ AV_{DD}$ -0.3 V to +0.3 V
Digital I/O Voltage to $GND^1$ -0.3 V to $V_{DD}$ + 0.3 V
Analog I/O Voltage to $GND^1$ -0.3 V to $V_{DD}$ + 0.3 V
$REF_{IN}\ to\ GND^1$ -0.3 V to $V_{DD}$ + 0.3 V
Operating Temperature Range-40°C to +85°C
Storage Temperature Range-65°C to +125°C
Maximum Junction Temperature150°C
Reflow Soldering
Peak Temperature260°C
Time at Peak Temperature40 sec

1 GND = AGND = DGND = CPGND = SDGND = AGNDVCO = 0 V.

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

This device is a high performance RF integrated circuit with an ESD rating of <1.5 kV and is ESD sensitive. Proper precautions should be taken for handling and assembly.

TRANSISTOR COUNT

The transistor count for the ADF4351 is 36,955 (CMOS) and 986 (bipolar).

THERMAL RESISTANCE

Thermal impedance $\left( \mathsf { \theta } _ { \mathrm { { J A } } } \right)$ is specified for a device with the exposed pad soldered to GND.

Table 4. Thermal Resistance

Package Type $\theta_{JA}$ Unit
32-Lead LFCSP (CP-32-7)27.3°C/W

ESD CAUTION

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS


Figure 3. Pin Configuration

Table 5. Pin Function Descriptions

Pin No.MnemonicDescription
1CLKSerial Clock Input. Data is clocked into the 32-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
2DATASerial Data Input. The serial data is loaded MSB first with the three LSBs as the control bits. This input is a high impedance CMOS input.
3LELoad Enable. When LE goes high, the data stored in the 32-bit shift register is loaded into the register that is selected by the three control bits. This input is a high impedance CMOS input.
4CEChip Enable. A logic low on this pin powers down the device and puts the charge pump into three-state mode. A logic high on this pin powers up the device, depending on the status of the power-down bits.
5SWFast Lock Switch. A connection should be made from the loop filter to this pin when using the fast lock mode.
6 $V_P$ Charge Pump Power Supply. $V_P$ must have the same value as $AV_{DD}$ . Place decoupling capacitors to the ground plane as close to this pin as possible.
7 $CP_{OUT}$ Charge Pump Output. When enabled, this output provides $\pm I_{CP}$ to the external loop filter. The output of the loop filter is connected to $V_{TUNE}$ to drive the internal VCO.
8 $CP_{GND}$ Charge Pump Ground. This output is the ground return pin for $CP_{OUT}$ .
9AGNDAnalog Ground. Ground return pin for $AV_{DD}$ .
10 $AV_{DD}$ Analog Power Supply. This pin ranges from 3.0 V to 3.6 V. Place decoupling capacitors to the analog ground plane as close to this pin as possible. $AV_{DD}$ must have the same value as $DV_{DD}$ .
11, 18, 21 $AGNDVCO$ VCO Analog Ground. Ground return pins for the VCO.
12 $RF_{OUTA+}$ VCO Output. The output level is programmable. The VCO fundamental output or a divided-down version is available.
13 $RF_{OUTA-}$ Complementary VCO Output. The output level is programmable. The VCO fundamental output or a divided-down version is available.
14 $RF_{OUTB+}$ Auxiliary VCO Output. The output level is programmable. The VCO fundamental output or a divided-down version is available.
15 $RF_{OUTB-}$ Complementary Auxiliary VCO Output. The output level is programmable. The VCO fundamental output or a divided-down version is available.
16, 17 $V_{VCO}$ Power Supply for the VCO. This pin ranges from 3.0 V to 3.6 V. Place decoupling capacitors to the analog ground plane as close to these pins as possible. $V_{VCO}$ must have the same value as $AV_{DD}$ .
19TEMPTemperature Compensation Output. Place decoupling capacitors to the ground plane as close to this pin as possible.
20 $V_{TUNE}$ Control Input to the VCO. This voltage determines the output frequency and is derived from filtering the $CP_{OUT}$ output voltage.
22 $R_{SET}$ Connecting a resistor between this pin and ground sets the charge pump output current. The nominal voltage bias at the $R_{SET}$ pin is 0.55 V. The relationship between $I_{CP}$ and $R_{SET}$ is as follows: $I_{CP} = 25.5/R_{SET}$ where: $R_{SET} = 5.1 \text{ k}\Omega$ . $I_{CP} = 5 \text{ mA}$ .
23 $V_{COM}$ Internal Compensation Node. Biased at half the tuning range. Place decoupling capacitors to the ground plane as close to this pin as possible.
24 $V_{REF}$ Reference Voltage. Place decoupling capacitors to the ground plane as close to this pin as possible.
25LDLock Detect Output Pin. A logic high output on this pin indicates PLL lock. A logic low output indicates loss of PLL lock.
26 $PDB_{RF}$ RF Power-Down. A logic low on this pin mutes the RF outputs. This function is also software controllable.
27DGNDDigital Ground. Ground return pin for $DV_{DD}$ .
28 $DV_{DD}$ Digital Power Supply. $DV_{DD}$ must have the same value as $AV_{DD}$ . Place decoupling capacitors to the ground plane as close to this pin as possible.
29 $REF_{IN}$ Reference Input. This CMOS input has a nominal threshold of $AV_{DD}/2$ and a dc equivalent input resistance of 100 kΩ. This input can be driven from a TTL or CMOS crystal oscillator, or it can be ac-coupled.
30MUXOUTMultiplexer Output. The multiplexer output allows the lock detect value, the N divider value, or the R counter value to be accessed externally.
31 $SD_{GND}$ Digital Σ-Δ Modulator Ground. Ground return pin for the Σ-Δ modulator.
32 $SDV_{DD}$ Power Supply Pin for the Digital Σ-Δ Modulator. $SDV_{DD}$ must have the same value as $AV_{DD}$ . Place decoupling capacitors to the ground plane as close to this pin as possible.
EPExposed PadExposed Pad. The LFCSP has an exposed pad that must be connected to GND.

TYPICAL PERFORMANCE CHARACTERISTICS


Figure 4. Open-Loop VCO Phase Noise, 2.2 GHz


Figure 7. Closed-Loop Phase Noise, Fundamental VCO and Dividers, VCO = 2.2 GHz, PFD = 25 MHz, Loop Filter Bandwidth = 63 kHz


Figure 5. Open-Loop VCO Phase Noise, 3.3 GHz


Figure 8. Closed-Loop Phase Noise, Fundamental VCO and Dividers, VCO = 3.3 GHz, PFD = 25 MHz, Loop Filter Bandwidth = 63 kHz


Figure 6. Open-Loop VCO Phase Noise, 4.4 GHz


Figure 9. Closed-Loop Phase Noise, Fundamental VCO and Dividers, VCO = 4.4 GHz, PFD = 25 MHz, Loop Filter Bandwidth = 63 kHz


Figure 10. Fractional-N Spur Performance, Low Noise Mode, W-CDMA Band; RFOUT= 2111.28 MHz, REFIN= 122.88 MHz, PFD= 30.72 MHz, Output Divide-by-2 Selected; Loop Filter Bandwidth = 60 kHz, Channel Spacing = 240 kHz; RMS Phase Error = 0.21°, RMS Jitter = 0.27 ps, EVM = 0.37%


Figure 11. Fractional-N Spur Performance, Low Spur Mode, W-CDMA Band; RFOUT= 2111.28 MHz, REFIN= 122.88 MHz, PFD= 30.72 MHz, Output Divide-by-2 Selected; Loop Filter Bandwidth = 60 kHz, Channel Spacing = 240 kHz; RMS Phase Error = 0.37°, RMS Jitter = 0.49 ps, EVM = 0.64%


Figure 12. Fractional-N Spur Performance, Low Noise Mode, W-CDMA Band; RFOUT= 2111.28 MHz, REFIN= 122.88 MHz, PFD= 30.72 MHz, Output Divide-by-2 Selected; Loop Filter Bandwidth = 20 kHz, Channel Spacing = 240 kHz; RMS Phase Error = 0.25°, RMS Jitter = 0.32 ps, EVM = 0.44%


Figure 13. Fractional-N Spur Performance, Low Noise Mode, LTE Band; RFOUT = 2646.96 MHz, REFIN = 122.88 MHz, PFD = 30.72 MHz; Loop Filter Bandwidth = 60 kHz, Channel Spacing = 240 kHz; Phase Word = 9, RMS Phase Error = 0.28°, RMS Jitter = 0.29 ps, EVM = 0.49%


Figure 14. Fractional-N Spur Performance, Low Spur Mode, LTE Band; RF = 2646.96 MHz, REF = 122.88 MHz, PFD = 30.72 MHz; Loop Filter Bandwidth = 60 kHz, Channel Spacing = 240 kHz; RMS Phase Error = 0.56°, RMS Jitter = 0.59 ps, EVM = 0.98%


Figure 15. Fractional-N Spur Performance, Low Noise Mode, W-CDMA Band; RFOUT = 2646.96 MHz, REFIN = 122.88 MHz, PFD = 30.72 MHz; Loop Filter Bandwidth = 20 kHz, Channel Spacing = 240 kHz; RMS Phase Error = 0.35°, RMS Jitter = 0.36 ps, EVM = 0.61%

CIRCUIT DESCRIPTION

REFERENCE INPUT SECTION

The reference input stage is shown in Figure 16. The SW1 and SW2 switches are normally closed. The SW3 switch is normally open. When power-down is initiated, SW3 is closed, and SW1 and SW2 are opened. In this way, no loading of the REFIN pin occurs during power-down.


Figure 16. Reference Input Stage

RF N DIVIDER

The RF N divider allows a division ratio in the PLL feedback path. The division ratio is determined by the INT, FRAC, and MOD values, which build up this divider (see Figure 17).


Figure 17. RF N Divider

INT, FRAC, MOD, and R Counter Relationship

The INT, FRAC, and MOD values, in conjunction with the R counter, make it possible to generate output frequencies that are spaced by fractions of the PFD frequency. For more information, see the RF Synthesizer—A Worked Example section.

The RF VCO frequency (RFOUT) equation is

$$
R F _ {O U T} = f _ {P F D} \times (I N T + (F R A C / M O D))\tag{1}
$$

where:

RFOUT is the output frequency of the voltage controlled oscillator (VCO).

INT is the preset divide ratio of the binary 16-bit counter (23 to 65,535 for the 4/5 prescaler; 75 to 65,535 for the 8/9 prescaler). FRAC is the numerator of the fractional division (0 to MOD − 1). MOD is the preset fractional modulus (2 to 4095).

The PFD frequency (fPFD) equation is

$$
f _ {P F D} = R E F _ {I N} \times [ (1 + D) / (R \times (1 + T)) ]\tag{2}
$$

where:

REFIN is the reference input frequency.

D is the REFIN doubler bit (0 or 1).

R is the preset divide ratio of the binary 10-bit programmable reference counter (1 to 1023).

T is the REFIN divide-by-2 bit (0 or 1).

Integer-N Mode

If FRAC = 0 and the DB8 (LDF) bit in Register 2 is set to 1, the synthesizer operates in integer-N mode. The DB8 bit in Register 2 should be set to 1 for integer-N digital lock detect.

R Counter

The 10-bit R counter allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the PFD. Division ratios from 1 to 1023 are allowed.

PHASE FREQUENCY DETECTOR (PFD) AND CHARGE PUMP

The phase frequency detector (PFD) takes inputs from the R counter and N counter and produces an output proportional to the phase and frequency difference between them. Figure 18 is a simplified schematic of the phase frequency detector.


Figure 18. PFD Simplified Schematic

The PFD includes a programmable delay element that sets the width of the antibacklash pulse (ABP). This pulse ensures that there is no dead zone in the PFD transfer function. Bit DB22 in Register 3 (R3) is used to set the ABP as follows:

When Bit DB22 is set to 0, the ABP width is programmed to 6 ns, the recommended value for fractional-N applications.

When Bit DB22 is set to 1, the ABP width is programmed to 3 ns, the recommended value for integer-N applications.

For integer-N applications, the in-band phase noise is improved by enabling the shorter pulse width. The PFD frequency can operate up to 90 MHz in this mode. To operate with PFD frequencies higher than 45 MHz, VCO band select must be disabled by setting the phase adjust bit (DB28) to 1 in Register 1.

MUXOUT AND LOCK DETECT

The multiplexer output on the ADF4351 allows the user to access various internal points on the chip. The state of MUXOUT is controlled by the M3, M2, and M1 bits in Register 2 (see Figure 26). Figure 19 shows the MUXOUT section in block diagram form.


Figure 19. MUXOUT Schematic

INPUT SHIFT REGISTERS

The ADF4351 digital section includes a 10-bit RF R counter, a 16-bit RF N counter, a 12-bit FRAC counter, and a 12-bit modulus counter. Data is clocked into the 32-bit shift register on each rising edge of CLK. The data is clocked in MSB first. Data is transferred from the shift register to one of six latches on the rising edge of LE. The destination latch is determined by the state of the three control bits (C3, C2, and C1) in the shift register. As shown in Figure 2, the control bits are the three LSBs: DB2, DB1, and DB0. Table 6 shows the truth table for these bits. Figure 23 summarizes how the latches are programmed.

Table 6. Truth Table for the C3, C2, and C1 Control Bits

Control BitsRegister
C3C2C1
000Register 0 (R0)
001Register 1 (R1)
010Register 2 (R2)
011Register 3 (R3)
100Register 4 (R4)
101Register 5 (R5)

PROGRAM MODES

Table 6 and Figure 23 through Figure 29 show how the program modes are set up in the ADF4351.

The following settings in the ADF4351 are double buffered: phase value, modulus value, reference doubler, reference divide-by-2, R counter value, and charge pump current setting. Before the part uses a new value for any double-buffered setting, the following two events must occur:

  1. The new value is latched into the device by writing to the appropriate register.

  2. A new write is performed on Register 0 (R0).

For example, any time that the modulus value is updated, Register 0 (R0) must be written to, to ensure that the modulus value is loaded correctly. The divider select value in Register 4 (R4) is also double buffered, but only if the DB13 bit of Register 2 (R2) is set to 1.

VCO

The VCO core in the ADF4351 consists of three separate VCOs, each of which uses 16 overlapping bands, as shown in Figure 20, to allow a wide frequency range to be covered without a large VCO sensitivity (KV) and resultant poor phase noise and spurious performance.


The correct VCO and band are selected automatically by the VCO and band select logic at power-up or whenever Register 0 (R0) is updated.

VCO and band selection take 10 PFD cycles multiplied by the value of the band select clock divider. The VCO VTUNE is disconnected from the output of the loop filter and is connected to an internal reference voltage.

The R counter output is used as the clock for the band select logic. A programmable divider is provided at the R counter output to allow division by an integer from 1 to 255; the divider value is set using Bits[DB19:DB12] in Register 4 (R4). When the required PFD frequency is higher than 125 kHz, the divide ratio should be set to allow enough time for correct band selection.

Band selection takes 10 cycles of the PFD frequency, equal to 80 µs. If faster lock times are required, Bit DB23 in Register 3 (R3) must be set to 1. This setting allows the user to select a higher band select clock frequency of up to 500 kHz, which speeds up the minimum band select time to 20 µs. For phase adjustments and small (<1 MHz) frequency adjustments, the user can disable VCO band selection by setting Bit DB28 in Register 1 (R1) to 1. This setting selects the phase adjust feature.

After band selection, normal PLL action resumes. The nominal value of $\mathrm { K } _ { \mathrm { V } }$ is 40 MHz/V when the N divider is driven from the VCO output or from this value divided by D. D is the output divider value if the N divider is driven from the RF divider output (selected by programming Bits[DB22:DB20] in Register 4). The ADF4351 contains linearization circuitry to minimize any variation of the product of ICP and KV to keep the loop bandwidth constant.

The VCO shows variation of KV as the VTUNE varies within the band and from band to band. For wideband applications covering a wide frequency range (and changing output dividers), a value of 40 MHz/V provides the most accurate $\mathrm { K } _ { \mathrm { V } }$ because this value is closest to an average value. Figure 21 shows how KV varies with fundamental VCO frequency, along with an average value for the frequency band. Users may prefer this figure when using narrow-band designs.


Figure 21. VCO Sensitivity (KV) vs. Frequency

OUTPUT STAGE

The RFOUTA+ and RFOUTA− pins of the ADF4351 are connected to the collectors of an NPN differential pair driven by buffered outputs of the VCO, as shown in Figure 22.


Figure 22. Output Stage

To allow the user to optimize the power dissipation vs. the output power requirements, the tail current of the differential pair is programmable using Bits[DB4:DB3] in Register 4 (R4). Four current levels can be set. These levels give output power levels of −4 dBm, −1 dBm, +2 dBm, and +5 dBm, using a 50 Ω resistor to $\mathrm { A V } _ { \mathrm { D D } }$ and ac coupling into a 50 Ω load. Alternatively, both outputs can be combined in a 1 + 1:1 transformer or a 180° microstrip coupler (see the Output Matching section).

If the outputs are used individually, the optimum output stage consists of a shunt inductor to $\mathrm { { V } _ { V C O } . }$ The unused complementary output must be terminated with a similar circuit to the used output.

An auxiliary output stage exists on the $\mathrm { R F _ { O U T } B + }$ and $\mathrm { R F _ { O U T } B - }$ pins, providing a second set of differential outputs that can be used to drive another circuit. The auxiliary output stage can be used only if the primary outputs are enabled. If the auxiliary output stage is not used, it can be powered down.

Another feature of the ADF4351 is that the supply current to the RF output stage can be shut down until the part achieves lock, as measured by the digital lock detect circuitry. This feature is enabled by setting the mute till lock detect (MTLD) bit in Register 4 (R4).

REGISTER MAPS

REGISTER 0

RESERVED16-BIT INTEGER VALUE (INT)12-BIT FRACTIONAL VALUE (FRAC)CONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
0N16N15N14N13N12N11N10N9N8N7N6N5N4N3N2N1F12F11F10F9F8F7F6F5F4F3F2F1C3(0)C2(0)C1(0)

REGISTER 1

RESERVEDPHASE ADJUSTPRESCALER12-BIT PHASE VALUE (PHASE) DBR $^{1}$ 12-BIT MODULUS VALUE (MOD) DBR $^{1}$ CONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
000PH1PR1P12P11P10P9P8P7P6P5P4P3P2P1M12M11M10M9M8M7M6M5M4M3M2M1C3(0)C2(0)C1(1)

REGISTER 2

RESERVEDLOWNOISE ANDLOW SPURMODESMUXOUTREFERENCE DOUBLER DBR1DBR110-BIT R COUNTER DBR1DOUBLE BUFFERCHARGE PUMP CURRENT SETTING DBR1LDFLDPPD POLARITYPOWER-DOWNCP THREE-STATECOUNTER RESETCONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
0L2L1M3M2M1RD2RD1R10R9R8R7R6R5R4R3R2R1D1CP4CP3CP2CP1U6U5U4U3U2U1C3(0)C2(1)C1(0)

REGISTER 3

RESERVEDBAND SELECT CLOCK MODEABPCHARGE CANCELRESERVEDCSRRESERVEDCLK DIV MODE12-BIT CLOCK DIVIDER VALUECONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
00000000F4F3F200F10C2C1D12D11D10D9D8D7D6D5D4D3D2D1C3(0)C2(1)C1(1)

REGISTER 4

RESERVEDFEEDBACK SELECTDBB $^{2}$ RF DIVIDER SELECT8-BIT BAND SELECT CLOCK DIVIDER VALUEVCO POWER-DOWNMTLDAUX OUTPUT SELECTAUX OUTPUT ENABLEAUX OUTPUT POWERRF OUTPUT ENABLEOUTPUT POWERCONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
00000000D13D12D11D10BS8BS7BS6BS5BS4BS3BS2BS1D9D8D7D6D5D4D3D2D1C3(1)C2(0)C1(0)

REGISTER 5

RESERVEDLD PIN MODERESERVEDRESERVEDRESERVEDCONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
00000000D15D140110000000000000000C3(1)C2(0)C1(1)

1DBR = DOUBLE-BUFFERED REGISTER—BUFFERED BY THE WRITE TO REGISTER 0. 2DBB = DOUBLE-BUFFERED BITS—BUFFERED BY THE WRITE TO REGISTER 0, IF AND ONLY IF DB13 OF REGISTER 2 IS HIGH.

Figure 23. Register Summary

RESERVEDPHASE ADJUSTPRESCALER12-BIT PHASE VALUE (PHASE) DBR12-BIT MODULUS VALUE (MOD) DBRCONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
000PH1PR1P12P11P10P9P8P7P6P5P4P3P2P1M12M11M10M9M8M7M6M5M4M3M2M1C3(0)C2(0)C1(1)
RESERVED16-BIT INTEGER VALUE (INT)12-BIT FRACTIONAL VALUE (FRAC)CONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
0N16N15N14N13N12N11N10N9N8N7N6N5N4N3N2N1F12F11F10F9F8F7F6F5F4F3F2F1C3(0)C2(0)C1(0)
N16N15...N5N4N3N2N1INTEGER VALUE (INT)
00...00000NOT ALLOWED
00...00001NOT ALLOWED
00...00010NOT ALLOWED
.............
00...10110NOT ALLOWED
00...1011123
00...1100024
.............
11...1110165,533
11...1111065,534
11...1111165,535

INTmin = 75 WITH PRESCALER = 8/9
Figure 24. Register 0 (R0)

F12F11...F2F1FRACTIONAL VALUE (FRAC)
00...000
00...011
00...102
00...113
........
........
........
11...004092
11...014093
11...104094
11...114095


Figure 25. Register 1 (R1)

M3M2M1OUTPUT
000THREE-STATE OUTPUT
001 $DV_{DD}$
010DGND
011R COUNTER OUTPUT
100N DIVIDER OUTPUT
101ANALOG LOCK DETECT
110DIGITAL LOCK DETECT
111RESERVED

Figure 26. Register 2 (R2)

Figure 27. Register 3 (R3)

RESERVEDFEEDBACK SELECTRF DIVIDER SELECT DBB8-BIT BAND SELECT CLOCK DIVIDER VALUEVCO POWER-DOWNMTLDAUX OUTPUT SELECTAUX OUTPUT ENABLEAUX OUTPUT POWERRF OUTPUT ENABLEOUTPUT POWERCONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
00000000D13D12D11D10BS8BS7BS6BS5BS4BS3BS2BS1D9D8D7D6D5D4D3D2D1C3(1)C2(0)C1(0)


Figure 28. Register 4 (R4)

RESERVEDLD PIN MODERESERVEDRESERVEDRESERVEDCONTROL BITS
DB31DB30DB29DB28DB27DB26DB25DB24DB23DB22DB21DB20DB19DB18DB17DB16DB15DB14DB13DB12DB11DB10DB9DB8DB7DB6DB5DB4DB3DB2DB1DB0
00000000D15D140110000000000000000C3(1)C2(0)C1(1)
D15D14LOCK DETECT PIN OPERATION
00LOW
01DIGITAL LOCK DETECT
10LOW
11HIGH

Figure 29. Register 5 (R5)

REGISTER 0

Control Bits

When Bits[C3:C1] are set to 000, Register 0 is programmed. Figure 24 shows the input data format for programming this register.

16-Bit Integer Value (INT)

The 16 INT bits (Bits[DB30:DB15]) set the INT value, which determines the integer part of the feedback division factor. The INT value is used in Equation 1 (see the INT, FRAC, MOD, and R Counter Relationship section). Integer values from 23 to 65,535 are allowed for the 4/5 prescaler; for the 8/9 prescaler, the minimum integer value is 75.

12-Bit Fractional Value (FRAC)

The 12 FRAC bits (Bits[DB14:DB3]) set the numerator of the fraction that is input to the Σ-Δ modulator. This fraction, along with the INT value, specifies the new frequency channel that the synthesizer locks to, as shown in the RF Synthesizer—A Worked Example section. FRAC values from 0 to (MOD − 1) cover channels over a frequency range equal to the PFD reference frequency.

REGISTER 1

Control Bits

When Bits[C3:C1] are set to 001, Register 1 is programmed. Figure 25 shows the input data format for programming this register.

Phase Adjust

The phase adjust bit (Bit DB28) enables adjustment of the output phase of a given output frequency. When phase adjustment is enabled (Bit DB28 is set to 1), the part does not perform VCO band selection or phase resync when Register 0 is updated. When phase adjustment is disabled (Bit DB28 is set to 0), the part performs VCO band selection and phase resync (if phase resync is enabled in Register 3, Bits[DB16:DB15]) when Register 0 is updated. Disabling VCO band selection is recommended only for fixed frequency applications or for frequency deviations of <1 MHz from the originally selected frequency.

Prescaler Value

The dual-modulus prescaler (P/P + 1), along with the INT, FRAC, and MOD values, determines the overall division ratio from the VCO output to the PFD input. The PR1 bit (DB27) in Register 1 sets the prescaler value.

Operating at CML levels, the prescaler takes the clock from the VCO output and divides it down for the counters. The prescaler is based on a synchronous 4/5 core. When the prescaler is set to 4/5, the maximum RF frequency allowed is 3.6 GHz. Therefore, when operating the ADF4351 above 3.6 GHz, the prescaler must be set to 8/9. The prescaler limits the INT value as follows:

Prescaler = 4/5: NMIN = 23

• Prescaler = 8/9: NMIN = 75

12-Bit Phase Value

Bits[DB26:DB15] control the phase word. The phase word must be less than the MOD value programmed in Register 1. The phase word is used to program the RF output phase from 0° to 360° with a resolution of 360°/MOD (see the Phase Resync section).

In most applications, the phase relationship between the RF signal and the reference is not important. In such applications, the phase value can be used to optimize the fractional and subfractional spur levels. For more information, see the Spur Consistency and Fractional Spur Optimization section.

If neither the phase resync nor the spurious optimization function is used, it is recommended that the phase word be set to 1.

12-Bit Modulus Value (MOD)

The 12 MOD bits (Bits[DB14:DB3]) set the fractional modulus. The fractional modulus is the ratio of the PFD frequency to the channel step resolution on the RF output. For more information, see the 12-Bit Programmable Modulus section.

REGISTER 2

Control Bits

When Bits[C3:C1] are set to 010, Register 2 is programmed. Figure 26 shows the input data format for programming this register.

Low Noise and Low Spur Modes

The noise mode on the ADF4351 is controlled by setting Bits[DB30:DB29] in Register 2 (see Figure 26). The noise mode allows the user to optimize a design either for improved spurious performance or for improved phase noise performance.

When the low spur mode is selected, dither is enabled. Dither randomizes the fractional quantization noise so that it resembles white noise rather than spurious noise. As a result, the part is optimized for improved spurious performance. Low spur mode is normally used for fast-locking applications when the PLL closed-loop bandwidth is wide. Wide loop bandwidth is a loop bandwidth greater than 1/10 of the RFOUT channel step resolution (fRES). A wide loop filter does not attenuate the spurs to the same level as a narrow loop bandwidth.

For best noise performance, use the low noise mode option. When the low noise mode is selected, dither is disabled. This mode ensures that the charge pump operates in an optimum region for noise performance. Low noise mode is extremely useful when a narrow loop filter bandwidth is available. The synthesizer ensures extremely low noise, and the filter attenuates the spurs. Figure 10 through Figure 12 show the trade-offs in a typical W-CDMA setup for different noise and spur settings.

MUXOUT

The on-chip multiplexer is controlled by Bits[DB28:DB26] (see Figure 26). Note that N counter output must be disabled for VCO band selection to operate correctly.

Reference Doubler

Setting the DB25 bit to 0 disables the doubler and feeds the REFIN signal directly into the 10-bit R counter. Setting this bit to 1 multiplies the REFIN frequency by a factor of 2 before feeding it into the 10-bit R counter. When the doubler is disabled, the REFIN falling edge is the active edge at the PFD input to the fractional synthesizer. When the doubler is enabled, both the rising and falling edges of REFIN become active edges at the PFD input.

When the doubler is enabled and the low spur mode is selected, the in-band phase noise performance is sensitive to the REFIN duty cycle. The phase noise degradation can be as much as 5 dB for REFIN duty cycles outside a 45% to 55% range. The phase noise is insensitive to the REFIN duty cycle in the low noise mode and when the doubler is disabled.

The maximum allowable REFIN frequency when the doubler is enabled is 30 MHz.

RDIV2

Setting the DB24 bit to 1 inserts a divide-by-2 toggle flip-flop between the R counter and the PFD, which extends the maximum REFIN input rate. This function allows a 50% duty cycle signal to appear at the PFD input, which is necessary for cycle slip reduction.

10-Bit R Counter

The 10-bit R counter (Bits[DB23:DB14]) allows the input reference frequency (REFIN) to be divided down to produce the reference clock to the PFD. Division ratios from 1 to 1023 are allowed.

Double Buffer

The DB13 bit enables or disables double buffering of Bits[DB22:DB20] in Register 4. For information about how double buffering works, see the Program Modes section.

Charge Pump Current Setting

Bits[DB12:DB9] set the charge pump current. This value should be set to the charge pump current that the loop filter is designed with (see Figure 26).

Lock Detect Function (LDF)

The DB8 bit configures the lock detect function (LDF). The LDF controls the number of PFD cycles monitored by the lock detect circuit to ascertain whether lock has been achieved. When DB8 is set to 0, the number of PFD cycles monitored is 40. When DB8 is set to 1, the number of PFD cycles monitored is 5. It is recommended that the DB8 bit be set to 0 for fractional-N mode and to 1 for integer-N mode.

Lock Detect Precision (LDP)

The lock detect precision bit (Bit DB7) sets the comparison window in the lock detect circuit. When DB7 is set to 0, the comparison window is 10 ns; when DB7 is set to 1, the window is 6 ns. The lock detect circuit goes high when n consecutive PFD cycles are less than the comparison window value; n is set by the LDF bit (DB8). For example, with DB8 = 0 and DB7 = 0, 40 consecutive PFD cycles of 10 ns or less must occur before digital lock detect goes high.

For fractional-N applications, the recommended setting for Bits[DB8:DB7] is 00; for integer-N applications, the recommended setting for Bits[DB8:DB7] is 11.

Phase Detector Polarity

The DB6 bit sets the phase detector polarity. When a passive loop filter or a noninverting active loop filter is used, this bit should be set to 1. If an active filter with an inverting charac teristic is used, this bit should be set to 0.

Power-Down (PD)

The DB5 bit provides the programmable power-down mode. Setting this bit to 1 performs a power-down. Setting this bit to 0 returns the synthesizer to normal operation. In software powerdown mode, the part retains all information in its registers. The register contents are lost only if the supply voltages are removed.

When power-down is activated, the following events occur:

• Synthesizer counters are forced to their load state conditions.

• VCO is powered down.

• Charge pump is forced into three-state mode.

• Digital lock detect circuitry is reset.

• RFOUT buffers are disabled.

Input registers remain active and capable of loading and latching data.

Charge Pump Three-State

Setting the DB4 bit to 1 puts the charge pump into three-state mode. This bit should be set to 0 for normal operation.

Counter Reset

The DB3 bit is the reset bit for the R counter and the N counter of the ADF4351. When this bit is set to 1, the RF synthesizer N counter and R counter are held in reset. For normal operation, this bit should be set to 0.

REGISTER 3

Control Bits

When Bits[C3:C1] are set to 011, Register 3 is programmed. Figure 27 shows the input data format for programming this register.

Band Select Clock Mode

Setting the DB23 bit to 1 selects a faster logic sequence of band selection, which is suitable for high PFD frequencies and is necessary for fast lock applications. Setting the DB23 bit to 0 is recommended for low PFD (<125 kHz) values. For the faster band select logic modes (DB23 set to 1), the value of the band select clock divider must be less than or equal to 254.

Antibacklash Pulse Width (ABP)

Bit DB22 sets the PFD antibacklash pulse width. When Bit DB22 is set to 0, the PFD antibacklash pulse width is 6 ns. This setting is recommended for fractional-N use. When Bit DB22 is set to 1, the PFD antibacklash pulse width is 3 ns, which results in phase noise and spur improvements in integer-N operation. For fractional-N operation, the 3 ns setting is not recommended.

Charge Cancelation

Setting the DB21 bit to 1 enables charge pump charge cancelation. This has the effect of reducing PFD spurs in integer-N mode. In fractional-N mode, this bit should be set to 0.

CSR Enable

Setting the DB18 bit to 1 enables cycle slip reduction. CSR is a method for improving lock times. Note that the signal at the phase frequency detector (PFD) must have a 50% duty cycle for cycle slip reduction to work. The charge pump current setting must also be set to a minimum. For more information, see the Cycle Slip Reduction for Faster Lock Times section.

Clock Divider Mode

Bits[DB16:DB15] must be set to 10 to activate phase resync (see the Phase Resync section). These bits must be set to 01 to activate fast lock (see the Fast Lock Timer and Register Sequences section). Setting Bits[DB16:DB15] to 00 disables the clock divider (see Figure 27).

12-Bit Clock Divider Value

Bits[DB14:DB3] set the 12-bit clock divider value. This value is the timeout counter for activation of phase resync (see the Phase Resync section). The clock divider value also sets the timeout counter for fast lock (see the Fast Lock Timer and Register Sequences section).

REGISTER 4

Control Bits

When Bits[C3:C1] are set to 100, Register 4 is programmed. Figure 28 shows the input data format for programming this register.

Feedback Select

The DB23 bit selects the feedback from the VCO output to the N counter. When this bit is set to 1, the signal is taken directly from the VCO. When this bit is set to 0, the signal is taken from the output of the output dividers. The dividers enable coverage of the wide frequency band (34.375 MHz to 4.4 GHz). When the dividers are enabled and the feedback signal is taken from the output, the RF output signals of two separately configured PLLs are in phase. This is useful in some applications where the positive interference of signals is required to increase the power.

RF Divider Select

Bits[DB22:DB20] select the value of the RF output divider (see Figure 28).

Band Select Clock Divider Value

Bits[DB19:DB12] set a divider for the band select logic clock input. By default, the output of the R counter is the value used to clock the band select logic, but, if this value is too high (>125 kHz), a divider can be switched on to divide the R counter output to a smaller value (see Figure 28).

VCO Power-Down

Setting the DB11 bit to 0 powers the VCO up; setting this bit to 1 powers the VCO down.

Mute Till Lock Detect (MTLD)

When the DB10 bit is set to 1, the supply current to the RF output stage is shut down until the part achieves lock, as measured by the digital lock detect circuitry.

AUX Output Select

The DB9 bit sets the auxiliary RF output. If DB9 is set to 0, the auxiliary RF output is the output of the RF dividers; if DB9 is set to 1, the auxiliary RF output is the fundamental VCO frequency.

AUX Output Enable

The DB8 bit enables or disables the auxiliary RF output. If DB8 is set to 0, the auxiliary RF output is disabled; if DB8 is set to 1, the auxiliary RF output is enabled.

AUX Output Power

Bits[DB7:DB6] set the value of the auxiliary RF output power level (see Figure 28).

RF Output Enable

The DB5 bit enables or disables the primary RF output. If DB5 is set to 0, the primary RF output is disabled; if DB5 is set to 1, the primary RF output is enabled.

Output Power

Bits[DB4:DB3] set the value of the primary RF output power level (see Figure 28).

REGISTER 5

Control Bits

When Bits[C3:C1] are set to 101, Register 5 is programmed. Figure 29 shows the input data format for programming this register.

Lock Detect Pin Operation

Bits[DB23:DB22] set the operation of the lock detect (LD) pin (see Figure 29).

REGISTER INITIALIZATION SEQUENCE

At initial power-up, after the correct application of voltages to the supply pins, the ADF4351 registers should be started in the following sequence:

  1. Register 5

  2. Register 4

  3. Register 3

  4. Register 2

  5. Register 1

  6. Register 0

RF SYNTHESIZER—A WORKED EXAMPLE

The following equations are used to program the ADF4351 synthesizer:

$$
R F _ {O U T} = \left[ I N T + (F R A C / M O D) \right] \times \left(f _ {P F D} / R F \text { Divider }\right)\tag{3}
$$

where:

RFOUT is the RF frequency output.

INT is the integer division factor.

FRAC is the numerator of the fractional division (0 to MOD − 1). MOD is the preset fractional modulus (2 to 4095).

RF Divider is the output divider that divides down the VCO frequency.

$$
f _ {P F D} = R E F _ {I N} \times [ (1 + D) / (R \times (1 + T)) ]\tag{4}
$$

where:

REFIN is the reference frequency input.

D is the RF REFIN doubler bit (0 or 1).

R is the RF reference division factor (1 to 1023).

T is the reference divide-by-2 bit (0 or 1).

As an example, a UMTS system requires a 2112.6 MHz RF frequency output (RFOUT); a 10 MHz reference frequency input (REFIN) is available and a 200 kHz channel resolution (fRESOUT) is required on the RF output.

Note that the ADF4351 VCO operates in the frequency range of 2.2 GHz to 4.4 GHz. Therefore, the RF divider of 2 should be used (VCO frequency = 4225.2 MHz, RFOUT = VCO frequency/ RF divider = 4225.2 MHz/2 = 2112.6 MHz).

It is also important where the loop is closed. In this example, the loop is closed before the output divider (see Figure 30).


Figure 30. Loop Closed Before Output Divider

Channel resolution $( \mathrm { f _ { R E S O U T } } )$ of 200 kHz is required at the output of the RF divider. Therefore, the channel resolution at the output of the VCO (fRES) needs to be $2 \times \mathrm { f _ { R E S O U T } }$ that is, 400 kHz.

$$
M O D = R E F _ {I N} / f _ {R E S}
$$

$$
M O D = 1 0 \mathrm{MHz} / 4 0 0 \mathrm{kHz} = 2 5
$$

From Equation 4,

$$
f _ {P F D} = [ 1 0 \mathrm{MHz} \times (1 + 0) / 1 ] = 1 0 \mathrm{MHz}\tag{5}
$$

$$
2 1 1 2. 6 \mathrm{MHz} = 1 0 \mathrm{MHz} \times [ (I N T + (F R A C / 2 5)) / 2 ]\tag{6}
$$

where:

$$
I N T = 4 2 2.
$$

$$
F R A C = 1 3.
$$

REFERENCE DOUBLER AND REFERENCE DIVIDER

The on-chip reference doubler allows the input reference signal to be doubled. Doubling the reference signal doubles the PFD comparison frequency, which improves the noise performance of the system. Doubling the PFD frequency usually improves noise performance by 3 dB. Note that in fractional-N mode, the PFD cannot operate above 32 MHz due to a limitation in the speed of the Σ-Δ circuit of the N divider. For integer-N applications, the PFD can operate up to 90 MHz.

The reference divide-by-2 divides the reference signal by 2, resulting in a 50% duty cycle PFD frequency. This is necessary for the correct operation of the cycle slip reduction (CSR) function. For more information, see the Cycle Slip Reduction for Faster Lock Times section.

12-BIT PROGRAMMABLE MODULUS

The choice of modulus (MOD) depends on the reference signal (REFIN) available and the channel resolution (fRES) required at the RF output. For example, a GSM system with 13 MHz REFIN sets the modulus to 65. This means that the RF output resolution (fRES) is the 200 kHz (13 MHz/65) necessary for GSM. With dither off, the fractional spur interval depends on the selected modulus values (see Table 7).

Unlike most other fractional-N PLLs, the ADF4351 allows the user to program the modulus over a 12-bit range. When combined with the reference doubler and the 10-bit R counter, the 12-bit modulus allows the user to set up the part in many different configurations for the application.

For example, consider an application that requires a 1.75 GHz RF frequency output with a 200 kHz channel step resolution. The system has a 13 MHz reference signal.

One possible setup is to feed the 13 MHz reference signal directly into the PFD and to program the modulus to divide by 65. This results in the required 200 kHz resolution.

Another possible setup is to use the reference doubler to create 26 MHz from the 13 MHz input signal. The 26 MHz is then fed into the PFD, and the modulus is programmed to divide by 130. This setup also results in 200 kHz resolution but offers superior phase noise performance over the first setup.

The programmable modulus is also very useful for multistandard applications. For example, if a dual-mode phone requires PDC and GSM 1800 standards, the programmable modulus is of great benefit.

PDC requires 25 kHz channel step resolution, whereas GSM 1800 requires 200 kHz channel step resolution. A 13 MHz reference signal can be fed directly to the PFD, and the modulus can be programmed to 520 when in PDC mode (13 MHz/520 = 25 kHz). The modulus must be reprogrammed to 65 for GSM 1800 operation (13 MHz/65 = 200 kHz).

It is important that the PFD frequency remain constant (in this example, 13 MHz). This allows the user to design one loop filter for both setups without encountering stability issues. Note that the ratio of the RF frequency to the PFD frequency principally affects the loop filter design, not the actual channel spacing.

CYCLE SLIP REDUCTION FOR FASTER LOCK TIMES

As described in the Low Noise and Low Spur Modes section, the ADF4351 contains a number of features that allow optimization for noise performance. However, in fast-locking applications, the loop bandwidth generally needs to be wide and, therefore, the filter does not provide much attenuation of the spurs. If the cycle slip reduction feature is enabled, the narrow loop bandwidth is maintained for spur attenuation, but faster lock times are still possible.

Cycle Slips

Cycle slips occur in integer-N/fractional-N synthesizers when the loop bandwidth is narrow compared to the PFD frequency. The phase error at the PFD inputs accumulates too fast for the PLL to correct, and the charge pump temporarily pumps in the wrong direction. This slows down the lock time dramatically. The ADF4351 contains a cycle slip reduction feature that extends the linear range of the PFD, allowing faster lock times without modifications to the loop filter circuitry.

When the circuitry detects that a cycle slip is about to occur, it turns on an extra charge pump current cell. This cell outputs a constant current to the loop filter or removes a constant current from the loop filter (depending on whether the VCO tuning voltage needs to increase or decrease to acquire the new frequency). The effect is that the linear range of the PFD is increased. Loop stability is maintained because the current is constant and is not a pulsed current.

If the phase error increases again to a point where another cycle slip is likely, the ADF4351 turns on another charge pump cell. This continues until the ADF4351 detects that the VCO frequency has exceeded the desired frequency. The extra charge pump cells are turned off one by one until all the extra charge pump cells are disabled and the frequency settles to the original loop filter bandwidth.

Up to seven extra charge pump cells can be turned on. In most applications, seven cells are enough to eliminate cycle slips altogether, providing much faster lock times.

Setting Bit DB18 in Register 3 to 1 enables cycle slip reduction. Note that the PFD requires a 45% to 55% duty cycle for CSR to operate correctly. If the REFIN frequency does not have a suitable duty cycle, enabling the RDIV2 mode (Bit DB24 in Register 2) ensures that the input to the PFD has a 50% duty cycle.

SPURIOUS OPTIMIZATION AND FAST LOCK

Narrow loop bandwidths can filter unwanted spurious signals, but these bandwidths usually have a long lock time. A wider loop bandwidth achieves faster lock times but may lead to increased spurious signals inside the loop bandwidth.

The fast lock feature can achieve the same fast lock time as the wider bandwidth but with the advantage of a narrow final loop bandwidth to keep spurs low.

FAST LOCK TIMER AND REGISTER SEQUENCES

If the fast lock mode is used, a timer value must be loaded into the PLL to determine the duration of the wide bandwidth mode.

When Bits[DB16:DB15] in Register 3 are set to 01 (fast lock enable), the timer value is loaded by the 12-bit clock divider value (Bits[DB14:DB3] in Register 3). The following sequence must be programmed to use fast lock:

  1. Start the initialization sequence (see the Register Initialization Sequence section). This sequence occurs only once after powering up the part.

  2. Load Register 3 by setting Bits[DB16:DB15] to 01 and by setting the selected fast lock timer value (Bits[DB14:DB3]). The duration that the PLL remains in wide bandwidth mode is equal to the fast lock timer/fPFD.

FAST LOCK EXAMPLE

If a PLL has a reference frequency of 13 MHz, fPFD of 13 MHz, and a required lock time of 60 µs, the PLL is set to wide bandwidth mode for 20 µs. This example assumes a modulus of 65 for channel spacing of 200 kHz. The VCO calibration time of 20 µs must also be taken into account (achieved by programming the higher band select clock mode using Bit DB23 of Register 3).

If the time set for the PLL lock time in wide bandwidth mode is 20 µs, then

Fast Lock Timer Value = (VCO Band Select Time +

PLL Lock Time in Wide Bandwidth) × fPFD/MOD

Fast Lock Timer Value = (20 µs + 20 µs) × 13 MHz/65 = 8

Therefore, a value of 8 must be loaded into the clock divider value in Register 3 (see Step 2 in the Fast Lock Timer and Register Sequences section).

Data Sheet

FAST LOCK LOOP FILTER TOPOLOGY

To use fast lock mode, the damping resistor in the loop filter is reduced to one-fourth its value while in wide bandwidth mode. To achieve the wider loop filter bandwidth, the charge pump current increases by a factor of 16; to maintain loop stability, the damping resistor must be reduced by a factor of one-fourth. To enable fast lock, the SW pin is shorted to the AGND pin by setting Bits[DB16:DB15] in Register 3 to 01. The following two topologies are available:

The damping resistor (R1) is divided into two values (R1 and R1A) that have a ratio of 1:3 (see Figure 31).

An extra resistor (R1A) is connected directly from SW, as shown in Figure 32. The extra resistor is calculated such that the parallel combination of the extra resistor and the damping resistor (R1) is reduced to one-fourth the original value of R1 (see Figure 32).


Figure 31. Fast Lock Loop Filter Topology 1


Figure 32. Fast Lock Loop Filter Topology 2

SPUR MECHANISMS

This section describes the three different spur mechanisms that arise with a fractional-N synthesizer and how to minimize them in the ADF4351.

Fractional Spurs

The fractional interpolator in the ADF4351 is a third-order Σ-Δ modulator with a modulus (MOD) that is programmable to any integer value from 2 to 4095. In low spur mode (dither on), the minimum allowable value of MOD is 50. The Σ-Δ modulator is clocked at the PFD reference rate (fPFD), which allows PLL output frequencies to be synthesized at a channel step resolution of fPFD/MOD.

In low noise mode (dither off), the quantization noise from the Σ-Δ modulator appears as fractional spurs. The interval between spurs is fPFD/L, where L is the repeat length of the code sequence in the digital Σ-Δ modulator. For the third-order Σ-Δ modulator used in the ADF4351, the repeat length depends on the value of MOD (see Table 7).

Table 7. Fractional Spurs with Dither Off (Low Noise Mode)

MOD Value (Dither Off)Repeat LengthSpur Interval
MOD is divisible by 2, but not by 32 × MODChannel step/2
MOD is divisible by 3, but not by 23 × MODChannel step/3
MOD is divisible by 66 × MODChannel step/6
MOD is not divisible by 2, 3, or 6MODChannel step

In low spur mode (dither on), the repeat length is extended to 221 cycles, regardless of the value of MOD, which makes the quantization error spectrum look like broadband noise. This may degrade the in-band phase noise at the PLL output by as much as 10 dB. For lowest noise, dither off is a better choice, particularly when the final loop bandwidth is low enough to attenuate even the lowest frequency fractional spur.

Integer Boundary Spurs

Another mechanism for fractional spur creation is the interactions between the RF VCO frequency and the reference frequency. When these frequencies are not integer related (the purpose of a fractional-N synthesizer), spur sidebands appear on the VCO output spectrum at an offset frequency that corresponds to the beat note, or difference frequency, between an integer multiple of the reference and the VCO frequency. These spurs are attenuated by the loop filter and are more noticeable on channels close to integer multiples of the reference, where the difference frequency can be inside the loop bandwidth (thus the name integer boundary spurs).

Reference Spurs

Reference spurs are generally not a problem in fractional-N synthesizers because the reference offset is far outside the loop bandwidth. However, any reference feedthrough mechanism that bypasses the loop may cause a problem. Feedthrough of low levels of on-chip reference switching noise, coupling to the VCO, can result in reference spur levels as high as −80 dBc. The PCB layout must ensure adequate isolation between VCO circuitry and the input reference to avoid a possible feedthrough path on the board.

SPUR CONSISTENCY AND FRACTIONAL SPUR OPTIMIZATION

With dither off, the fractional spur pattern due to the quantization noise of the Σ-Δ modulator also depends on the particular phase word with which the modulator is seeded.

The phase word can be varied to optimize the fractional and subfractional spur levels on any particular frequency. Thus, a lookup table of phase values corresponding to each frequency can be created for use when programming the ADF4351.

If a lookup table is not used, keep the phase word at a constant value to ensure consistent spur levels on any particular frequency.

PHASE RESYNC

The output of a fractional-N PLL can settle to any one of the MOD phase offsets with respect to the input reference, where MOD is the fractional modulus. The phase resync feature of the ADF4351 produces a consistent output phase offset with respect to the input reference. This phase offset is necessary in applications where the output phase and frequency are important, such as digital beamforming. See the Phase Programmability section to program a specific RF output phase when using phase resync.

Phase resync is enabled by setting Bits[DB16:DB15] in Register 3 to 10. When phase resync is enabled, an internal timer generates sync signals at intervals of tSYNC given by the following formula:

$$
t _ {S Y N C} = C L K _ D I V _ V A L U E \times M O D \times t _ {P F D}
$$

where:

CLK_DIV_VALUE is the decimal value programmed in Bits[DB14:DB3] of Register 3. This value can be any integer from 1 to 4095.

MOD is the modulus value programmed in Bits[DB14:DB3] of Register 1 (R1).

tPFD is the PFD reference period.

When a new frequency is programmed, the second sync pulse after the LE rising edge is used to resynchronize the output phase to the reference. The tSYNC time must be programmed to a value that is at least as long as the worst-case lock time. This guarantees that the phase resync occurs after the last cycle slip in the PLL settling transient.

In the example shown in Figure 33, the PFD reference is 25 MHz and MOD = 125 for a 200 kHz channel spacing. tSYNC is set to 400 µs by programming CLK_DIV_VALUE = 80.


Figure 33. Phase Resync Example

Phase Programmability

The phase word in Register 1 controls the RF output phase. As this word is swept from 0 to MOD, the RF output phase sweeps over a 360° range in steps of 360°/MOD. In many applications, it is advisable to disable VCO band selection by setting Bit DB28 in Register 1 (R1) to 1. This setting selects the phase adjust feature.

High PFD Frequencies

VCO band selection is required to ensure that the correct VCO band is chosen for the relevant frequency. VCO band selection can operate with PFD frequencies up to 45 MHz using the high VCO band select mode (set Bit DB23 in Register 3 to 1).

For PFD frequencies higher than 45 MHz, it is recommended that the user perform the following steps:

  1. Program the desired VCO frequency with phase adjustment disabled (set Bit DB28 in Register 1 to 0). Ensure that the PFD frequency is less than 45 MHz.

  2. After the correct frequency is achieved, enable phase adjustment (set Bit DB28 in Register 1 to 1).

  3. PFD frequencies higher than 32 MHz are permissible only with integer-N applications; therefore, set the antibacklash pulse width to 3 ns (set Bit DB22 in Register 3 to 1).

  4. Using the desired PFD frequency, program the appropriate values for the reference R and feedback N counters.

Using this procedure, the lowest rms in-band phase noise can be achieved.

APPLICATIONS INFORMATION DIRECT CONVERSION MODULATOR

Direct conversion architectures are increasingly being used to implement base station transmitters. Figure 34 shows how Analog Devices, Inc., parts can be used to implement such a system.

Figure 34 shows the AD9788 TxDAC® used with the ADL5375. The use of dual integrated DACs, such as the AD9788 with its specified ±2% FSR and ±0.001% FSR gain and offset characteristics, ensures minimum error contribution (over temperature) from this portion of the signal chain.

The local oscillator (LO) is implemented using the ADF4351. The low-pass filter was designed using ADIsimPLL™ for a channel spacing of 200 kHz and a closed-loop bandwidth of 35 kHz.

The LO ports of the ADL5375 can be driven differentially from the complementary RFOUTA± outputs of the ADF4351. This setup provides better performance than a single-ended LO driver and eliminates the use of a balun to convert from a single-ended LO input to the more desirable differential LO input for the ADL5375. The typical rms phase noise (100 Hz to 5 MHz) of the LO in this configuration is 0.61° rms.

The ADL5375 accepts LO drive levels from −6 dBm to +6 dBm. The optimum LO power can be software programmed on the ADF4351, which allows levels from −4 dBm to +5 dBm from each output.

The RF output is designed to drive a 50 Ω load, but it must be ac-coupled, as shown in Figure 34. If the I and Q inputs are driven in quadrature by 2 V p-p signals, the resulting output power from the ADL5375 modulator is approximately 2 dBm.


Figure 34. Direct Conversion Modulato

INTERFACING TO THE ADuC70xx AND THE ADSP-BF527

The ADF4351 has a simple SPI-compatible serial interface for writing to the device. The CLK, DATA, and LE pins control the data transfer. When LE goes high, the 32 bits that were clocked into the appropriate register on each rising edge of CLK are transferred to the appropriate latch. See Figure 2 for the timing diagram and Table 6 for the register address table.

ADuC70xx Interface

Figure 35 shows the interface between the ADF4351 and the ADuC70xx family of analog microcontrollers. The ADuC70xx family is based on an AMR7 core, but the same interface can be used with any 8051-based microcontroller.


Figure 35. ADuC70xx to ADF4351 Interface

The microcontroller is set up for SPI master mode with CPHA = 0. To initiate the operation, the I/O port driving LE is brought low. Each latch of the ADF4351 needs a 32-bit word, which is accomplished by writing four 8-bit bytes from the microcontroller to the device. After the fourth byte is written, the LE input should be brought high to complete the transfer.

When power is first applied to the ADF4351, the part requires six writes (one each to R5, R4, R3, R2, R1, and R0) for the output to become active.

I/O port lines on the microcontroller are also used to control the power-down input (CE) and to detect lock (MUXOUT configured as lock detect and polled by the port input).

When operating in the mode described, the maximum SPI transfer rate of the ADuC70xx is 20 Mbps. This means that the maximum rate at which the output frequency can be changed is 833 kHz. If using a faster SPI clock, make sure that the SPI timing requirements listed in Table 2 are adhered to.

ADSP-BF527 Interface

Figure 36 shows the interface between the ADF4351 and the Blackfin® ADSP-BF527 digital signal processor (DSP). The ADF4351 needs a 32-bit serial word for each latch write. The easiest way to accomplish this using the Blackfin family is to use the autobuffered transmit mode of operation with alternate framing. This mode provides a means for transmitting an entire block of serial data before an interrupt is generated.


Figure 36. ADSP-BF527 to ADF4351 Interface

Set up the word length for eight bits and use four memory locations for each 32-bit word. To program each 32-bit latch, store the four 8-bit bytes, enable the autobuffered mode, and write to the transmit register of the DSP. This last operation initiates the autobuffer transfer. Make sure that the SPI timing requirements listed in Table 2 are adhered to.

PCB DESIGN GUIDELINES FOR A CHIP SCALEPACKAGE

The lands on the chip scale package (CP-32-7) are rectangular. The PCB pad for these lands must be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. Each land must be centered on the pad to ensure that the solder joint size is maximized.

The bottom of the chip scale package has a central exposed thermal pad. The thermal pad on the PCB must be at least as large as the exposed pad. On the PCB, there must be a minimum clearance of 0.25 mm between the thermal pad and the inner edges of the pad pattern to ensure that shorting is avoided.

Thermal vias can be used on the PCB thermal pad to improve the thermal performance of the package. If vias are used, they must be incorporated into the thermal pad at 1.2 mm pitch grid. The via diameter must be between 0.3 mm and 0.33 mm, and the via barrel must be plated with 1 oz. of copper to plug the via.

OUTPUT MATCHING

For optimum operation, the output of the ADF4351 can be matched in a number of ways; the most basic method is to connect a 50 Ω resistor to VVCO. A dc bypass capacitor of 100 pF is connected in series, as shown in Figure 37. Because the resistor is not frequency dependent, this method provides a good broadband match. When connected to a 50 Ω load, this circuit typically gives a differential output power equal to the value selected by Bits[DB4:DB3] in Register 4 (R4).


Figure 37. Simple Output Stage

A better solution is to use a shunt inductor (acting as an RF choke) to $\mathrm { \Delta V _ { V C O } . }$ This solution gives a better match and, therefore, more output power.

Experiments have shown that the circuit shown in Figure 38 provides an excellent match to 50 Ω for the W-CDMA UMTS Band 1 (2110 MHz to 2170 MHz). The maximum output power in this case is approximately 5 dBm. Both single-ended architectures can be examined using the EVAL-ADF4351EB1Z evaluation board.


Figure 38. Optimum Output Stage

If differential outputs are not needed, the unused output can be terminated, or both outputs can be combined using a balun.

A balun using discrete inductors and capacitors can be implemented with the architecture shown in Figure 39. The LC balun comprises Component L1 and Component C1. L2 provides a dc path for $\mathrm { R F _ { O U T } A ^ { - } }$ , and Capacitor C2 is used for dc blocking.


Figure 39. LC Balun for the ADF4351

Table 8. LC Balun Components

Frequency Range (MHz)Inductor L1 (nH)Capacitor C1 (pF)RF Choke Inductor L2 (nH)DC Blocking Capacitor C2 (pF)Measured Output Power (dBm)
137 to 3001001039010009
300 to 460515.618012010
400 to 600305.612012010
600 to 9001846812010
860 to 1240122.239109
1200 to 16005.61.215109
1600 to 36003.30.710108
2800 to 38002.20.510108

(CP-32-7)

OUTLINE DIMENSIONS

Figure 40. 32-Lead Lead Frame Chip Scale Package [LFCSP]

5 mm × 5 mm Body and 0.75 mm Package Height

Dimensions shown in millimeters

ORDERING GUIDE

Model1Temperature RangePackage DescriptionPackage Option
ADF4351BCPZ-40°C to +85°C32-Lead Lead Frame Chip Scale Package [LFCSP]CP-32-7
ADF4351BCPZ-RL7-40°C to +85°C32-Lead Lead Frame Chip Scale Package [LFCSP]CP-32-7
EVAL-ADF4351EB1ZEvaluation Board

1 Z = RoHS Compliant Part.

Extracted Images

Figures and diagrams from the PDF

Preview the extracted datasheet assets and open any image in a separate tab for closer inspection.

885143dde9a127b31aaff56fd6b1a0594ba98aa19ec82b4fa16d6af351ee3b16.jpg

885143dde9a127b31aaff56fd6b1a0594ba98aa19ec82b4fa16d6af351ee3b16.jpg

f81428d425d0e0237d39b2a8862ed0df64fa248fab145f6ef5865aaed20d0898.jpg

f81428d425d0e0237d39b2a8862ed0df64fa248fab145f6ef5865aaed20d0898.jpg

ba67f68f957b4b6bd073f544246d54e409fb2c0b5af028dca97d6c5aa45beccc.jpg

ba67f68f957b4b6bd073f544246d54e409fb2c0b5af028dca97d6c5aa45beccc.jpg

6b86c12e76cf269d185a8460a00a1bd6403e4067b9c193cffe848c3be36c52ef.jpg

6b86c12e76cf269d185a8460a00a1bd6403e4067b9c193cffe848c3be36c52ef.jpg

1e017bc8ad04faa8a454d5162cc4a0bd741bc2b7fa98a603a3e5d71341ff697a.jpg

1e017bc8ad04faa8a454d5162cc4a0bd741bc2b7fa98a603a3e5d71341ff697a.jpg

0a58933b7d4a9ba383a928974bd6362167aca06aa70151127da94435b084cf94.jpg

0a58933b7d4a9ba383a928974bd6362167aca06aa70151127da94435b084cf94.jpg

323ee6271adff6dcdac65ba0da97321b01980e8f727d2447d5dfc4bc717be571.jpg

323ee6271adff6dcdac65ba0da97321b01980e8f727d2447d5dfc4bc717be571.jpg

b3f6f138149d8e7f463ae51582a5249f7fc8dd43950c46499b3d4439eaa1af30.jpg

b3f6f138149d8e7f463ae51582a5249f7fc8dd43950c46499b3d4439eaa1af30.jpg

c0d3d4420cda6a5122d9533f79918f5d1c7e893f87e29e5860038cc9e9869191.jpg

c0d3d4420cda6a5122d9533f79918f5d1c7e893f87e29e5860038cc9e9869191.jpg

e86a13cf8b2eed2aa97052b12afe76b869d42b0e911e7ffb33dc5ca8c6ed003b.jpg

e86a13cf8b2eed2aa97052b12afe76b869d42b0e911e7ffb33dc5ca8c6ed003b.jpg

92e9382ef2e814b136743a1ec10bc6c1137fc5997aac0fff18ea2e25dc828172.jpg

92e9382ef2e814b136743a1ec10bc6c1137fc5997aac0fff18ea2e25dc828172.jpg

4435cb7dce3ea4a00cfd3fe0e9d861b8a7589a0dce8f2843872676ea2ee58f97.jpg

4435cb7dce3ea4a00cfd3fe0e9d861b8a7589a0dce8f2843872676ea2ee58f97.jpg

aa8d74fb305a3db9a245cf98e7c4fd2993d0721f54e90726ed54e510681840e0.jpg

aa8d74fb305a3db9a245cf98e7c4fd2993d0721f54e90726ed54e510681840e0.jpg

a53288eb1100052ef481ea46e4e8979546d9d6d954bb7fe8803ff267c2911f0c.jpg

a53288eb1100052ef481ea46e4e8979546d9d6d954bb7fe8803ff267c2911f0c.jpg

1b965bb4f55f386a0dc2c5cc8c60fedba2e8c8d43ba61f5d07f2c80c4fc6ad60.jpg

1b965bb4f55f386a0dc2c5cc8c60fedba2e8c8d43ba61f5d07f2c80c4fc6ad60.jpg

a0b6567f9e105a9ac6e5a060653f9c5fb8cb8fd6e84f633a468c3f431dc579ae.jpg

a0b6567f9e105a9ac6e5a060653f9c5fb8cb8fd6e84f633a468c3f431dc579ae.jpg

6289c8ae78707a97b54d394b2faa1a0077dbc000b1e0ce1bb649103ed623dc3f.jpg

6289c8ae78707a97b54d394b2faa1a0077dbc000b1e0ce1bb649103ed623dc3f.jpg

c26ee38f7736a90cb043312fddc08912c9ab55883138733751b39e1a5ffe8191.jpg

c26ee38f7736a90cb043312fddc08912c9ab55883138733751b39e1a5ffe8191.jpg

df84b8239c46f641ef4303c0e885a1bfce0a7a7ad9b6324613816b6802fb29db.jpg

df84b8239c46f641ef4303c0e885a1bfce0a7a7ad9b6324613816b6802fb29db.jpg

dc6ff73b1fbf881787a031aee9dff0d2622b6cf16d7e19d8144f2f388327856c.jpg

dc6ff73b1fbf881787a031aee9dff0d2622b6cf16d7e19d8144f2f388327856c.jpg

253f0a18e224d9700f10a95ee69167817e5d54eae8f84b404b682124a5796eda.jpg

253f0a18e224d9700f10a95ee69167817e5d54eae8f84b404b682124a5796eda.jpg

3d1656578143bb6cd65259e9b6ab13d507e0e3b17725288c307e8aab06af8b67.jpg

3d1656578143bb6cd65259e9b6ab13d507e0e3b17725288c307e8aab06af8b67.jpg

4d3214932a21ddd16dfd49b6e90958f9f58405277a2f41fa1178c7a254c823bc.jpg

4d3214932a21ddd16dfd49b6e90958f9f58405277a2f41fa1178c7a254c823bc.jpg

d72f969c007e77008d33b6724ae322dd48a6202d82845eca40158274aed2ef91.jpg

d72f969c007e77008d33b6724ae322dd48a6202d82845eca40158274aed2ef91.jpg

a7cba4f266b2a366e09a6f8a5c58ea3230a36330fd40b4c352f2588c65ad6baf.jpg

a7cba4f266b2a366e09a6f8a5c58ea3230a36330fd40b4c352f2588c65ad6baf.jpg

19fbd9b9959f3cd1dda6d260e165601cc19e21440e3a0e0431c378df155f3caf.jpg

19fbd9b9959f3cd1dda6d260e165601cc19e21440e3a0e0431c378df155f3caf.jpg

ad58e9e9964eaae015d072cb22c16755d1c5e54422821a5b2da74f2bae506e96.jpg

ad58e9e9964eaae015d072cb22c16755d1c5e54422821a5b2da74f2bae506e96.jpg

f86a7804d9dc87f25693ac13b189f21c3d91c4f1514c4db111aec40e3cc147eb.jpg

f86a7804d9dc87f25693ac13b189f21c3d91c4f1514c4db111aec40e3cc147eb.jpg

9ffc364f8a5ee4bd6845dd3aefa7784cceaa08d6f39c1baf2fbab38f3d716c37.jpg

9ffc364f8a5ee4bd6845dd3aefa7784cceaa08d6f39c1baf2fbab38f3d716c37.jpg

af88041e5007ba04ea90af71d5e853a055757266d6a371e892302e844eee473a.jpg

af88041e5007ba04ea90af71d5e853a055757266d6a371e892302e844eee473a.jpg

fc548f3a7b01249e904325d97a61e4c69da14b677b1c729156f7ea9903d57535.jpg

fc548f3a7b01249e904325d97a61e4c69da14b677b1c729156f7ea9903d57535.jpg

25f2e76d709cb9efba933b1170c29541a72e9e9d0bab193ec6be4e1cc2a91bf9.jpg

25f2e76d709cb9efba933b1170c29541a72e9e9d0bab193ec6be4e1cc2a91bf9.jpg

1ff5c93918c837e72b60ae3d43639fdd68bac2fbac3259e1eec404f348edfea3.jpg

1ff5c93918c837e72b60ae3d43639fdd68bac2fbac3259e1eec404f348edfea3.jpg

a5e1d52d1b895eb2fdd8b44b8165d770ac03b53f91a78156a8bc8eb320a34441.jpg

a5e1d52d1b895eb2fdd8b44b8165d770ac03b53f91a78156a8bc8eb320a34441.jpg

1e38acdb5774969707578bd746cf778364d2b46adcf95326e4f6aa0388b1d490.jpg

1e38acdb5774969707578bd746cf778364d2b46adcf95326e4f6aa0388b1d490.jpg

dd8e91746b3efb37b9dc4c5458ac820c2f7095caf1c0d414c03f28ebf5e8c830.jpg

dd8e91746b3efb37b9dc4c5458ac820c2f7095caf1c0d414c03f28ebf5e8c830.jpg

2baaa4d5205f0554c529e954381a69736df3c6bb7d725b99ad2945434256a55a.jpg

2baaa4d5205f0554c529e954381a69736df3c6bb7d725b99ad2945434256a55a.jpg

e345f60f60e6680dd83d09db85b12d4c482009867fbb03586850c0b622f1c4a7.jpg

e345f60f60e6680dd83d09db85b12d4c482009867fbb03586850c0b622f1c4a7.jpg

88639d4d35f693622e546f006c774645c52f14239b34c1a58d7391cb360e3a16.jpg

88639d4d35f693622e546f006c774645c52f14239b34c1a58d7391cb360e3a16.jpg

614426ba6eabe16f1f02013a90f0dd1544209e0d6a2d34710cf52f2ff1e6d9a6.jpg

614426ba6eabe16f1f02013a90f0dd1544209e0d6a2d34710cf52f2ff1e6d9a6.jpg

7594961dd36c63954e70c4e03d7d66f13fcd7fd617c783c5a523070a1d276f54.jpg

7594961dd36c63954e70c4e03d7d66f13fcd7fd617c783c5a523070a1d276f54.jpg

e1676024ec20533991c00a582768340ad046f4af95347fe1307e6c550afc04ca.jpg

e1676024ec20533991c00a582768340ad046f4af95347fe1307e6c550afc04ca.jpg

f955962802809bf7712426ca63e0cb9610bca32af5c11e0569fead8d1fac4b81.jpg

f955962802809bf7712426ca63e0cb9610bca32af5c11e0569fead8d1fac4b81.jpg

57beaa11b5d5511e1b97343144c5a343ea3bcd0a95592c8962fa6345503c5bf7.jpg

57beaa11b5d5511e1b97343144c5a343ea3bcd0a95592c8962fa6345503c5bf7.jpg

3cc811d724688b6df06ceef9656beaac59b12860778de1073343a4fd272532eb.jpg

3cc811d724688b6df06ceef9656beaac59b12860778de1073343a4fd272532eb.jpg

751fba575b00bb0ffa707b7f5619d8e8c2ee0ae14fea69980867eb0f196cc2dc.jpg

751fba575b00bb0ffa707b7f5619d8e8c2ee0ae14fea69980867eb0f196cc2dc.jpg

f681989733b5899ac07e228b20b2facd11669748acaafb3805ecc0db2dc825aa.jpg

f681989733b5899ac07e228b20b2facd11669748acaafb3805ecc0db2dc825aa.jpg

cf4e9ac325bc4d74fc617a30043758d142f61c0d10cbeffba117a79f07b0cd3f.jpg

cf4e9ac325bc4d74fc617a30043758d142f61c0d10cbeffba117a79f07b0cd3f.jpg

f35f65733ab2b9072992e6debff79b5604daff57d32451413a8ddf7c201df61f.jpg

f35f65733ab2b9072992e6debff79b5604daff57d32451413a8ddf7c201df61f.jpg

8e5a6f82c63e167150e1047ade7635434886781fd29ae657f812e6acd7a93b83.jpg

8e5a6f82c63e167150e1047ade7635434886781fd29ae657f812e6acd7a93b83.jpg

d7223a7657270873c7bf12457ec8a8b1d0eca441da1ffef72c845293f74c399d.jpg

d7223a7657270873c7bf12457ec8a8b1d0eca441da1ffef72c845293f74c399d.jpg

6ffadc7857179df8083410958a8061bb26f3e57b79fe6eb334e754ce415b7758.jpg

6ffadc7857179df8083410958a8061bb26f3e57b79fe6eb334e754ce415b7758.jpg

46b17fbca203f632cb175d07fa1b9851a02b0d4cb28aa12ef86253b01de2a63d.jpg

46b17fbca203f632cb175d07fa1b9851a02b0d4cb28aa12ef86253b01de2a63d.jpg

667411d6c0a6f85ab6b14528b2a1d667a86278aaedbcf607a4648875f8f9aa30.jpg

667411d6c0a6f85ab6b14528b2a1d667a86278aaedbcf607a4648875f8f9aa30.jpg

b3a529654d06d77a2dfbf5276cbd1fcf7008421c816b2c5ec1039e8191b0a974.jpg

b3a529654d06d77a2dfbf5276cbd1fcf7008421c816b2c5ec1039e8191b0a974.jpg

9f9f7c8f347a6b1d2d762ef7452bd28ad933880c358d455894f63de3cd3018a6.jpg

9f9f7c8f347a6b1d2d762ef7452bd28ad933880c358d455894f63de3cd3018a6.jpg

d3ce0136cc495268f8c90620f93a0a451641edfda44d52ac57e2973c33722e37.jpg

d3ce0136cc495268f8c90620f93a0a451641edfda44d52ac57e2973c33722e37.jpg

0c8c89f9734d8fe344e46161661d2f75f5b5ac6c2ff34a75440ab5557fd69285.jpg

0c8c89f9734d8fe344e46161661d2f75f5b5ac6c2ff34a75440ab5557fd69285.jpg

e09c1ef32fd480c1d4306862650c117cf8c6b678e0b7c9f070a1806f432237f5.jpg

e09c1ef32fd480c1d4306862650c117cf8c6b678e0b7c9f070a1806f432237f5.jpg

03b20fdaad8f203a9ffbd1427160e70d1f25335d91b42fc6ab2d4b20b1e79684.jpg

03b20fdaad8f203a9ffbd1427160e70d1f25335d91b42fc6ab2d4b20b1e79684.jpg

Agent APIs

Use this datasheet from any agent

Send the page, markdown, chunks, or search endpoint to ChatGPT, Claude, embedr-app, or your own tooling.