ESP32-S3-DevKitC-1-N8R8 v1.1
Entry-level ESP32-S3 development board with Wi-Fi, Bluetooth LE, USB, USB-to-UART bridge, 8 MB flash, and 8 MB PSRAM.
Espressif ESP32-S3-DevKitC-1-N8R8 v1.1
Scope
This processed manufacturer user guide is the primary source for the Espressif ESP32-S3-DevKitC-1 v1.1 development board, with the N8R8 ordering code (ESP32-S3-WROOM-1-N8R8 module, PCB antenna). The board exposes two fixed 1x22, 2.54 mm header rows. It is not a bare ESP32-S3-WROOM land pattern.
Board-specific implementation notes
- The v1.1 addressable RGB LED is driven by GPIO38. The initial/older board uses GPIO48 instead; do not mix those revisions.
- Espressif documents USB, 5V/GND header power, and 3V3/GND header power as mutually exclusive power paths unless the carrier intentionally manages source isolation.
- GPIO35, GPIO36, and GPIO37 are not externally available on Octal flash/PSRAM and WROOM-2 variants. They remain physical header pads on this carrier geometry but are unavailable for the selected N8R8 board's Octal memory configuration.
- The official v1.1 PCB layout gives a nominal board size of 25.40 mm x 62.74 mm, 2.54 mm header pitch, 22.86 mm row spacing, and an approximately 8.00 mm USB-side connector overhang.
Source provenance
Manufacturer: Espressif Systems. Hardware revision: ESP32-S3-DevKitC-1 v1.1. Ordering code: ESP32-S3-DevKitC-1-N8R8. The complete source set is linked from the component record: the v1.1 user guide, schematic, PCB layout drawing, dimensions PDF/DXF, and Espressif's KiCad library.
Extracted manufacturer guide
ESP32-S3 esp-dev-kits Documentation
Release master
Espressif Systems
Jul 02, 2026
Table of contents
Table of contents i
1 ESP32-S3-DevKitC-1 3 1.1 ESP32-S3-DevKitC-1 v1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1.3 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1.4 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 ESP32-S3-USB-OTG 17 2.1 ESP32-S3-USB-OTG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2.1.3 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3 ESP32-S3-LCD-EV-Board 31 3.1 ESP32-S3-LCD-EV-Board v1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.1.1 Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 3.1.2 Start Application Development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.1.3 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 3.1.4 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 3.1.5 Sample Request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 3.1.6 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4 ESP-VoCat 65 4.1 ESP-VoCat v1.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 4.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 4.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 4.1.3 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 4.1.4 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5 ESP-DualKey 91 5.1 ESP-DualKey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 5.1.1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 5.1.2 Hardware Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 5.1.3 Hardware Revision Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 5.1.4 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6 EOL (End of Life) Boards 97 6.1 ESP32-S3-DevKitM-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 6.1.1 ESP32-S3-DevKitM-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 6.2 ESP32-S3-USB-Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 6.2.1 ESP32-S3-USB-Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7 Related Documentation and Resources 113 7.1 Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 7.2 Developer Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
i
7.3 Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
7.4 Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
8 Disclaimer and Copyright Notice 115
ii
Table of contents
This document provides detailed user guides and examples for ESP32-S3 series development boards.
Note: For the full list of Espressif development boards, please go to ESP DevKits.
Espressif Systems 1 Release master Submit Document Feedback
Table of contents
Espressif Systems 2 Release master Submit Document Feedback
Chapter 1
ESP32-S3-DevKitC-1
The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, ESP32-S3- WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® Low Energy MCU module that integrates complete Wi-Fi and Bluetooth Low Energy functions. Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard.
1.1 ESP32-S3-DevKitC-1 v1.1
The older version: ESP32-S3-DevKitC-1 v1.0 This user guide will help you get started with ESP32-S3-DevKitC-1 and will also provide more in-depth information. The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, ESP32-S3- WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® Low Energy MCU module that integrates complete Wi-Fi and Bluetooth Low Energy functions. Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard. The document consists of the following major sections: • Getting started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: Revision history, known issues, and links to user guides for previous versions (if any) of the board. • Related Documents: Links to related documentation.
1.1.1 Getting Started
This section provides a brief introduction of ESP32-S3-DevKitC-1, instructions on how to do the initial hardware setup and how to flash firmware onto it.
Description of Components
The key components of the board are described in a counter-clockwise direction.
3
Chapter 1. ESP32-S3-DevKitC-1
Fig. 1: ESP32-S3-DevKitC-1 with ESP32-S3-WROOM-1 Module
Fig. 2: ESP32-S3-DevKitC-1 - front
Espressif Systems 4 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Key Component Description ESP32-S3-WROOM-1/1U/2 ESP32-S3-WROOM-1, ESP32-S3-WROOM-1U, and ESP32-S3-WROOM- 2 are powerful, generic Wi-Fi + Bluetooth Low Energy MCU modules that have a rich set of peripherals. They provide acceleration for neural net- work computing and signal processing workloads. ESP32-S3-WROOM-1 and ESP32-S3-WROOM-2 comes with a PCB antenna. ESP32-S3-WROOM-1U comes with an external antenna connector. 5 V to 3.3 V LDO Power regulator that converts a 5 V supply into a 3.3 V output. Pin Headers All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming. For details, please see Header Block. USB-to-UART Port A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB- to-UART bridge. Boot Button Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port. Reset Button Press this button to restart the system. USB Port ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 speci- fication. The interface is used for power supply to the board, for flashing appli- cations to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging. USB-to-UART Bridge Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps. RGB LED Addressable RGB LED, driven by GPIO38. 3.3 V Power On LED Turns on when the USB power is connected to the board.
Note: For boards with Octal SPI flash/PSRAM memory embedded ESP32-S3-WROOM-1/1U modules, and boards with ESP32-S3-WROOM-2 modules, the pins GPIO35, GPIO36 and GPIO37 are used for the internal communi- cation between ESP32-S3 and SPI flash/PSRAM memory, thus not available for external use.
Start Application Development
Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.
Required Hardware • ESP32-S3-DevKitC-1 • USB 2.0 cable (Standard-A to Micro-B) • Computer running Windows, Linux, or macOS
Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Hardware Setup Connect the board with the computer using USB-to-UART Port or ESP32-S3 USB Port. In subsequent steps, USB-to-UART Port will be used by default.
Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel- opment environment and then flash an application example onto your board.
Espressif Systems 5 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Contents and Packaging
Ordering Information The development board has a variety of variants to choose from, as shown in the table below.
Ordering Code Module Integrated Flash PSRAM SPI Voltage ESP32-S3-DevKitC-1- ESP32-S3-WROOM-1- 8 MB QD 8 MB OT 3.3 V N8R8 N8R8 ESP32-S3-DevKitC-1- ESP32-S3-WROOM-2- 32 MB OT 16 MB OT 1.8 V N32R16V N32R16V ESP32-S3-DevKitC-1U- ESP32-S3-WROOM-1U- 8 MB QD 8 MB OT 3.3 V N8R8 N8R8
Note: In the table above, QD stands for Quad SPI and OT stands for Octal SPI.
Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or any packaging depending on your retailer. For retail orders, please go to https://www.espressif.com/en/contact-us/get-samples.
Wholesale Orders If you order in bulk, the boards come in large cardboard boxes. For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.
1.1.2 Hardware Reference
Block Diagram
The block diagram below shows the components of ESP32-S3-DevKitC-1 and their interconnections.
Power Supply Options There are three mutually exclusive ways to provide power to the board: • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended) • 5V and G (GND) pins • 3V3 and G (GND) pins
Header Block
The two tables below provide the Name and Function of the pins on both sides of the board (J1 and J3). The pin names are shown in ESP32-S3-DevKitC-1 - front. The numbering is the same as in the Board Schematic (PDF).
Espressif Systems 6 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Fig. 3: ESP32-S3-DevKitC-1 (click to enlarge)
J1
No. Name TypePage 8, 1 Function 1 3V3 P 3.3 V power supply 2 3V3 P 3.3 V power supply 3 RST I EN 4 4 I/O/T RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3 5 5 I/O/T RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4 6 6 I/O/T RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5 7 7 I/O/T RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6 8 15 I/O/T RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P 9 16 I/O/T RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N 10 17 I/O/T RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6 11 18 I/O/T RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3 12 8 I/O/T RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1 13 3 I/O/T RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2 14 46 I/O/T GPIO46 15 9 I/O/T RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD 16 10 I/O/T RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4, SUB- SPICS0 17 11 I/O/T RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5, SUBSPID 18 12 I/O/T RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6, SUB- SPICLK 19 13 I/O/T RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7, SUBSPIQ 20 14 I/O/T RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS, SUB- SPIWP 21 5V P 5 V power supply 22 G G Ground
Espressif Systems 7 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
J3
No. Name Type Function
1 G G Ground
2 TX I/O/T U0TXD, GPIO43, CLK_OUT1
3 RX I/O/T U0RXD, GPIO44, CLK_OUT2
4 1 I/O/T RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
5 2 I/O/T RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
6 42 I/O/T MTMS, GPIO42
7 41 I/O/T MTDI, GPIO41, CLK_OUT1
8 40 I/O/T MTDO, GPIO40, CLK_OUT2
9 39 I/O/T MTCK, GPIO39, CLK_OUT3, SUBSPICS1
10 38 I/O/T GPIO38, FSPIWP, SUBSPIWP, RGB LED
11 37 I/O/T SPIDQS, GPIO37, FSPIQ, SUBSPIQ
12 36 I/O/T SPIIO7, GPIO36, FSPICLK, SUBSPICLK
13 35 I/O/T SPIIO6, GPIO35, FSPID, SUBSPID
14 0 I/O/T RTC_GPIO0, GPIO0
15 45 I/O/T GPIO45
16 48 I/O/T GPIO48, SPICLK_N, SUBSPICLK_N_DIFF
17 47 I/O/T GPIO47, SPICLK_P, SUBSPICLK_P_DIFF
18 21 I/O/T RTC_GPIO21, GPIO21
19 20 I/O/T RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
20 19 I/O/T RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
21 G G Ground
22 G G Ground
For description of function names, please refer to ESP32-S3 Series Datasheet (PDF).
Fig. 4: ESP32-S3-DevKitC-1 Pin Layout (click to enlarge)
Pin Layout 1 P: Power supply; I: Input; O: Output; T: High impedance.
Espressif Systems 8 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
1.1.3 Hardware Revision Details
Initial release
Note: Both the initial and v1.1 versions of ESP32-S3-DevKitC-1 are available on the market. The main difference lies in the GPIO assignment for the RGB LED: the initial version uses GPIO48, whereas v1.1 uses GPIO38.
1.1.4 Related Documents
• ESP32-S3 Datasheet (PDF)
• ESP32-S3-WROOM-1 & ESP32-S3-WROOM-1U Datasheet (PDF)
• ESP32-S3-WROOM-2 Datasheet (PDF)
• ESP32-S3-DevKitC-1 Schematic (PDF)
• ESP32-S3-DevKitC-1 PCB layout (PDF)
• ESP32-S3-DevKitC-1 Dimensions (PDF)
• ESP32-S3-DevKitC-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online
• ESP32-S3-DevKitC-1 Reference Design (ZIP)
For further design documentation for the board, please contact us at sales@espressif.com.
ESP32-S3-DevKitC-1 v1.0
The latest version: ESP32-S3-DevKitC-1 v1.1 This user guide will help you get started with ESP32-S3-DevKitC-1 and will also provide more in-depth information. The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, ESP32-S3- WROOM-1U, or ESP32-S3-WROOM-2, a general-purpose Wi-Fi + Bluetooth® Low Energy MCU module that integrates complete Wi-Fi and Bluetooth Low Energy functions. Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard. The document consists of the following major sections: • Getting started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: Revision history, known issues, and links to user guides for previous versions (if any) of the board. • Related Documents: Links to related documentation.
Getting Started This section provides a brief introduction of ESP32-S3-DevKitC-1, instructions on how to do the initial hardware setup and how to flash firmware onto it.
Description of Components The key components of the board are described in a counter-clockwise direction.
Espressif Systems 9 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Fig. 5: ESP32-S3-DevKitC-1 with ESP32-S3-WROOM-1 Module
Fig. 6: ESP32-S3-DevKitC-1 - front
Espressif Systems 10 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Key Component Description ESP32-S3-WROOM-1/1U/2 ESP32-S3-WROOM-1, ESP32-S3-WROOM-1U, and ESP32-S3-WROOM- 2 are powerful, generic Wi-Fi + Bluetooth Low Energy MCU modules that have a rich set of peripherals. They provide acceleration for neural net- work computing and signal processing workloads. ESP32-S3-WROOM-1 and ESP32-S3-WROOM-2 comes with a PCB antenna. ESP32-S3-WROOM-1U comes with an external antenna connector. 5 V to 3.3 V LDO Power regulator that converts a 5 V supply into a 3.3 V output. Pin Headers All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming. For details, please see Header Block. USB-to-UART Port A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB- to-UART bridge. Boot Button Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port. Reset Button Press this button to restart the system. ESP32-S3 USB Port ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 speci- fication. The interface is used for power supply to the board, for flashing appli- cations to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging. USB-to-UART Bridge Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps. RGB LED Addressable RGB LED, driven by GPIO48. 3.3 V Power On LED Turns on when the USB power is connected to the board.
Note: For boards with Octal SPI flash/PSRAM memory embedded ESP32-S3-WROOM-1/1U modules, and boards with ESP32-S3-WROOM-2 modules, the pins GPIO35, GPIO36 and GPIO37 are used for the internal communi- cation between ESP32-S3 and SPI flash/PSRAM memory, thus not available for external use.
Start Application Development Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.
Required Hardware • ESP32-S3-DevKitC-1 • USB 2.0 cable (Standard-A to Micro-B) • Computer running Windows, Linux, or macOS
Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Hardware Setup Connect the board with the computer using USB-to-UART Port. Connection using ESP32-S3 USB Port is not fully implemented in software. In subsequent steps, USB-to-UART Port will be used by default.
Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel- opment environment and then flash an application example onto your board.
Contents and Packaging
Espressif Systems 11 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Ordering Information The development board has a variety of variants to choose from, as shown in the table below.
Ordering Code Module Integrated Flash PSRAM SPI Voltage ESP32-S3-DevKitC-1- ESP32-S3-WROOM-1- 8 MB QD 8 MB OT 3.3 V N8R8 N8R8 ESP32-S3-DevKitC-1- ESP32-S3-WROOM-2- 32 MB OT 16 MB OT 1.8 V N32R16V N32R16V ESP32-S3-DevKitC-1U- ESP32-S3-WROOM-1U- 8 MB QD 8 MB OT 3.3 V N8R8 N8R8
Note: In the table above, QD stands for Quad SPI and OT stands for Octal SPI.
Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or any packaging depending on your retailer. For retail orders, please go to https://www.espressif.com/en/company/contact/buy-a-sample.
Wholesale Orders If you order in bulk, the boards come in large cardboard boxes. For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.
Hardware Reference
Block Diagram The block diagram below shows the components of ESP32-S3-DevKitC-1 and their interconnec- tions.
Power Supply Options There are three mutually exclusive ways to provide power to the board: • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended) • 5V and G (GND) pins • 3V3 and G (GND) pins
Header Block The two tables below provide the Name and Function of the pins on both sides of the board (J1 and J3). The pin names are shown in ESP32-S3-DevKitC-1 - front. The numbering is the same as in the Board Schematic (PDF).
Espressif Systems 12 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Fig. 7: ESP32-S3-DevKitC-1 (click to enlarge)
J1
No. Name TypePage 14, 1 Function 1 3V3 P 3.3 V power supply 2 3V3 P 3.3 V power supply 3 RST I EN 4 4 I/O/T RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3 5 5 I/O/T RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4 6 6 I/O/T RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5 7 7 I/O/T RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6 8 15 I/O/T RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P 9 16 I/O/T RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N 10 17 I/O/T RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6 11 18 I/O/T RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3 12 8 I/O/T RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1 13 3 I/O/T RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2 14 46 I/O/T GPIO46 15 9 I/O/T RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD 16 10 I/O/T RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4, SUB- SPICS0 17 11 I/O/T RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5, SUBSPID 18 12 I/O/T RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6, SUB- SPICLK 19 13 I/O/T RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7, SUBSPIQ 20 14 I/O/T RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS, SUB- SPIWP 21 5V P 5 V power supply 22 G G Ground
Espressif Systems 13 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
J3
No. Name Type Function
1 G G Ground
2 TX I/O/T U0TXD, GPIO43, CLK_OUT1
3 RX I/O/T U0RXD, GPIO44, CLK_OUT2
4 1 I/O/T RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
5 2 I/O/T RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
6 42 I/O/T MTMS, GPIO42
7 41 I/O/T MTDI, GPIO41, CLK_OUT1
8 40 I/O/T MTDO, GPIO40, CLK_OUT2
9 39 I/O/T MTCK, GPIO39, CLK_OUT3, SUBSPICS1
10 38 I/O/T GPIO38, FSPIWP, SUBSPIWP
11 37 I/O/T SPIDQS, GPIO37, FSPIQ, SUBSPIQ
12 36 I/O/T SPIIO7, GPIO36, FSPICLK, SUBSPICLK
13 35 I/O/T SPIIO6, GPIO35, FSPID, SUBSPID
14 0 I/O/T RTC_GPIO0, GPIO0
15 45 I/O/T GPIO45
16 48 I/O/T GPIO48, SPICLK_N, SUBSPICLK_N_DIFF, RGB LED
17 47 I/O/T GPIO47, SPICLK_P, SUBSPICLK_P_DIFF
18 21 I/O/T RTC_GPIO21, GPIO21
19 20 I/O/T RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
20 19 I/O/T RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
21 G G Ground
22 G G Ground
For description of function names, please refer to Chip Datasheet (PDF).
Pin Layout
Hardware Revision Details This is the first revision of this board released.
Related Documents • ESP32-S3 Datasheet (PDF) • ESP32-S3-WROOM-1 & ESP32-S3-WROOM-1U Datasheet (PDF) • ESP32-S3-WROOM-2 Datasheet (PDF) • ESP32-S3-DevKitC-1 Schematic (PDF) • ESP32-S3-DevKitC-1 PCB layout (PDF) • ESP32-S3-DevKitC-1 Dimensions (PDF) • ESP32-S3-DevKitC-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online For further design documentation for the board, please contact us at sales@espressif.com.
1 P: Power supply; I: Input; O: Output; T: High impedance.
Espressif Systems 14 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Fig. 8: ESP32-S3-DevKitC-1 Pin Layout (click to enlarge)
Espressif Systems 15 Release master Submit Document Feedback
Chapter 1. ESP32-S3-DevKitC-1
Espressif Systems 16 Release master Submit Document Feedback
Chapter 2
ESP32-S3-USB-OTG
ESP32-S3-USB-OTG is a development board that focuses on USB-OTG function verification and application devel- opment. Application examples for this board can be found at Examples .
2.1 ESP32-S3-USB-OTG
ESP32-S3-USB-OTG is a development board that focuses on USB-OTG function verification and application devel- opment. It is based on ESP32-S3 SoC, supports Wi-Fi and BLE 5.0 wireless functions, and supports USB host and USB device functions. It can be used to develop applications such as wireless storage devices, Wi-Fi network cards, LTE MiFi, multimedia devices, virtual keyboards and mice. The development board has the following features: • Onboard ESP32-S3-MINI-1-N8 module, with built-in 8 MB flash • Onboard USB Type-A host and device interface, with built-in USB interface switching circuit • Onboard USB to serial debugging chip (Micro USB interface) • Onboard 1.3-inch LCD color screen, supports GUI • Onboard SD card interface, compatible with SDIO and SPI interfaces • Onboard charging IC, can be connected to lithium battery The document consists of the following major sections: • Getting Started: Provides a brief overview of ESP32-S3-USB-OTG and necessary hardware and software in- formation. • Hardware Reference: Provides detailed hardware information of ESP32-S3-USB-OTG. • Related Documents: Provides links to related documents.
2.1.1 Getting Started
This section describes how to start using ESP32-S3-USB-OTG. It includes introduction to basic information about ESP32-S3-USB-OTG first, and then on how to start using the development board for application development, as well as board packaging and retail information.
Description of Components
The ESP32-S3-USB-OTG development board includes the following parts: • Motherboard: ESP32-S3-USB-OTG motherboard is the core of the kit. The motherboard integrates the ESP32-S3-MINI-1 module and provides an interface of the 1.3-inch LCD screen.
17
Chapter 2. ESP32-S3-USB-OTG
Fig. 1: ESP32-S3-USB-OTG (click to enlarge)
Espressif Systems 18 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Fig. 2: ESP32-S3-USB-OTG Top View (click to enlarge)
Espressif Systems 19 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
The following table starts with the USB_HOST Interface on the left, and introduces the main components in the above figure in an anticlockwise order.
Main components Description USB_HOST Interface USB Type-A female port, used to connect other USB devices. ESP32-S3-MINI-1 Module ESP32-S3-MINI-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module that has a rich set of peripherals. It has strong ability for neural network com- puting and signal processing. ESP32-S3-MINI-1 comes with a PCB antenna and is pin-to-pin compatible with ESP32-S2-MINI-1. MENU Button Menu button. Micro SD Card Slot Micro SD card can be inserted. Both four-line SDIO and SPI mode are sup- ported. USB Switch IC By setting the level of USB_SEL, you can switch USB peripherals to make them either connected to the USB_DEV interface or the USB_HOST interface. USB_DEV will be connected by default. Reset Button Press this button to restart the system. USB_DEV Interface USB Type-A male port, can be connected to the USB host, and also used as a lithium battery charge power source. Power Switch Switch to ON to use battery power. Switch to OFF to power off battery. Boot Button Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port. DW- Button Down button. LCD FPC Connector Used to connect the 1.3-inch LCD screen. UP+ Button Up button. USB-to-UART Interface A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB- to-UART bridge.
The following table starts with the Yellow LED on the left, and introduces the main components in the above figure in an anticlockwise order.
Main components Description Yellow LED Driven by GPIO16, set high level to turn on. Green LED Driven by GPIO15, set high level to turn on. Charging LED During charging, the red light is on, which will be turned off when charged. Battery Solder Joints 3.6 V lithium battery can be welded to power the motherboard. Charging Circuit Used to charge lithium battery. Free Pins Idle pins that can be customized. USB-to-UART Bridge Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
• Subboard: ESP32-S3-USB-OTG-SUB mount the 1.3-inch LCD screen
Application Examples
The following application examples are available for ESP32-S3-USB-OTG: • factory - Demonstrates a factory demo for the ESP32-S3-USB-OTG development board, providing a reference for building, flashing, and monitoring projects using ESP-IDF and ESP Launchpad. For more examples and the latest updates, please refer to the examples folder. To explore the application examples or to develop your own, please follow the steps outlined in the Start Application Development section.
Espressif Systems 20 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Fig. 3: ESP32-S3-USB-OTG Bottom View (click to enlarge)
Fig. 4: ESP32-S3-USB-OTG Subboard (click to enlarge)
Espressif Systems 21 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Start Application Development
Before powering on the ESP32-S3-USB-OTG, please make sure that the development board is intact.
Required Hardware • ESP32-S3-USB-OTG • A USB 2.0 data cable (standard A to Micro-B) • Computer (Windows, Linux or macOS)
Software Setup Please proceed to Get Started, where Section Installation Step by Step will quickly help you set up the development environment and then flash an application example onto your board.
Contents and Packaging
Retail Orders If you order a few samples, each board comes in an individual package in either an antistatic bag or any packaging depending on your retailer.
Fig. 5: ESP32-S3-USB-OTG Package (click to enlarge)
Which contains the following parts: • Motherboard: – ESP32-S3-USB-OTG • Subboard: – ESP32-S3-USB-OTG_SUB • Fastener – Mounting bolt (x4) – Screw (x4)
Espressif Systems 22 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
– Nut (x4)
For retail orders, please go to https://www.espressif.com/zh-hans/company/contact/buy-a-sample.
Wholesale Order If purchased in bulk, the development board will be packaged in a large cardboard box. For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.
2.1.2 Hardware Reference
Block Diagram
The block diagram below shows the components of ESP32-S3-USB-OTG and their interconnections.
Fig. 6: ESP32-S3-USB-OTG Block Diagram (click to enlarge)
Please note that the external interface corresponding to the USB_HOST D+ D- signal in the functional block diagram is USB DEV, which means that ESP32-S3 is used as a device to receive signals from other USB hosts. The external interface corresponding to the USB_DEV D+ D- signal is USB HOST, which means that ESP32-S3 acts as a host to control other devices.
Power Supply Options
There are three power supply methods for the development board:
- Power supply through the Micro_USB interface • Use the USB cable (standard A to Micro-B) to connect the motherboard to a power supply device, and set battery switch to OFF. Please note that in this power supply mode, only the motherboard and display are powered.
- Power supply through the USB_DEV interface
Espressif Systems 23 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
• Set DEV_VBUS_EN to high level, and set the battery switch to OFF. This mode can supply power to the
USB HOST interface. The lithium battery will be charged at the same time (if the lithium battery is
installed)
- Power supply through the battery • Set BOOST_EN to high level, and set the battery switch to ON. You should solder a 1-Serial lithium battery (3.7 V ~ 4.2 V) to the power solder joint reserved on the back of the motherboard first. This mode can supply power to the USB HOST interface at the same time. The battery interface description is as follows: Fig. 7: Battery Connection (click to enlarge)
USB HOST Interface Power Options
The USB HOST interface (Type-A female port) can supply power to the connected USB device. The power supply voltage is 5 V and the maximum current is 500 mA. • There are two power supply methods for the USB HOST interface: 1. Power is supplied through the USB_DEV interface, and the 5 V power is directly from the power source connected to the interface. 2. Power is supplied through the lithium battery, and the 3.6 V ~ 4.2 V voltage of the lithium battery is boosted to 5 V through the Boost circuit. The working status of Boost IC can be controlled by BOOST_EN/GPIO13, set high to enable Boost. • USB HOST interface power supply selection:
Espressif Systems 24 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Fig. 8: Boost Circuit (click to enlarge)
BOOST_EN DEV_VBUS_EN Power Source 0 1 USB_DEV 1 0 Battery 0 0 No output 1 1 Undefined
Fig. 9: Power Switch Circuit (click to enlarge)
• 500 mA current limiting circuit:
1. The current limiting IC MIC2005A can limit the maximum output current of the USB HOST interface
to 500 mA. Please set the IDEV_LIMIT_EN (GPIO17) to high level to enable the current-limiting IC
to output voltage.
Espressif Systems 25 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Fig. 10: 500 mA Current Limiting Circuit (click to enlarge)
Fig. 11: USB Interface Switch Circuit (click to enlarge)
Espressif Systems 26 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
USB Interface Switch Circuit
• When USB_SEL (GPIO18) is set to high level, the USB D+/D- Pin (GPIO19, 20) will be connected to
USB_DEV D+ D-. Then you can use the USB HOST interface (Type-A female Port) to connect other USB
devices.
• When USB_SEL (GPIO18) is set to low level, the USB D+/D- Pin (GPIO19, 20) will be connected to
USB_HOST D+ D-. Then you can use the USB DEV interface (Type-A male port) to connect to a host like
a PC.
• USB_SEL is pulled low level by default.
LCD Interface
Fig. 12: LCD Interface Circuit (click to enlarge)
Please note that this interface supports connecting SPI interface screens. The screen controller used by this develop- ment board is ST7789, and LCD_BL (GPIO9) can be used to control the screen backlight.
SD Card Interface
Please note that the SD card interface is compatible with 1-wire, 4-wire SDIO mode and SPI mode. After being powered on, the card will be in 3.3 V signaling mode. Please send the first CMD0 command to select the bus mode: SD mode or SPI mode.
Charging Circuit
Please note that the Type-A male port can be connected to a power adapter that outputs 5 V. When charging the battery, the red indicator LED is on, after fully charged, the red indicator LED is off. When using the charging circuit, please set the battery switch to OFF. The charging current is 212.7 mA.
Espressif Systems 27 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Fig. 13: SD Card Interface Circuit (click to enlarge)
Fig. 14: Charging Circuit (click to enlarge)
Espressif Systems 28 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
Pin Layout
Function pin:
No. ESP32-S3-MINI- Description 1 Pin 1 GPIO18 USB_SEL: Used to switch the USB interface. When high level, the USB_HOST interface is enabled. When low level (default), the USB_DEV interface is enabled. 2 GPIO19 Connect with USB D-. 3 GPIO20 Connect with USB D+. 4 GPIO15 LED_GREEN: the light is lit when set high level. 5 GPIO16 LED_YELLOW: the light is lit when set high level. 6 GPIO0 BUTTON_OK: OK button, low level when pressed. 7 GPIO11 BUTTON_DW: Down button, low level when pressed. 8 GPIO10 BUTTON_UP: UP button, low level when pressed. 9 GPIO14 BUTTON_MENU: Menu button, low level when pressed. 10 GPIO8 LCD_RET: used to reset LCD, low level to reset. 11 GPIO5 LCD_EN: used to enable LCD, low level to enable. 12 GPIO4 LCD_DC: Used to switch data and command status. 13 GPIO6 LCD_SCLK: LCD SPI Clock. 14 GPIO7 LCD_SDA: LCD SPI MOSI. 15 GPIO9 LCD_BL: LCD backlight control. 16 GPIO36 SD_SCK: SD SPI CLK / SDIO CLK. 17 GPIO37 SD_DO: SD SPI MISO / SDIO Data0. 18 GPIO38 SD_D1: SDIO Data1. 19 GPIO33 SD_D2: SDIO Data2. 20 GPIO34 SD_D3: SD SPI CS / SDIO Data3. 21 GPIO1 HOST_VOL: USB_DEV voltage monitoring, ADC1 channel 0. 22 GPIO2 BAT_VOL: Battery voltage monitoring, ADC1 channel 1. 23 GPIO17 LIMIT_EN: Enable current limiting IC, high level enable. 24 GPIO21 0VER_CURRENT: Current overrun signal, high level means overrun. 25 GPIO12 DEV_VBUS_EN: High level to enable DEV_VBUS power supply. 26 GPIO13 BOOST_EN: High level to enable Boost boost circuit.
Extended pin:
No. ESP32-S3-MINI-1 Pin Description 1 GPIO45 FREE_1: Idle, can be customized. 2 GPIO46 FREE_2: Idle, can be customized. 3 GPIO48 FREE_3: Idle, can be customized. 4 GPIO26 FREE_4: Idle, can be customized. 5 GPIO47 FREE_5: Idle, can be customized. 6 GPIO3 FREE_6: Idle, can be customized.
2.1.3 Related Documents
Please download the following documents from the HTML version of esp-dev-kits Documentation. • ESP32-S3 Datasheet (PDF) • ESP32-S3-MINI-1/1U Datasheet (PDF) • Espressif Product Selection Tool • ESP32-S3-USB-OTG Schematic Diagram (PDF) • ESP32-S3-USB-OTG PCB Layout Drawing (PDF) • ESP32-S3-USB-OTG Reference Design (ZIP)
Espressif Systems 29 Release master Submit Document Feedback
Chapter 2. ESP32-S3-USB-OTG
• ST7789VW Datasheet (PDF)
Espressif Systems 30 Release master Submit Document Feedback
Chapter 3
ESP32-S3-LCD-EV-Board
ESP32-S3-LCD-EV-Board is a development board for evaluating and verifying esp32s3 screen interactive applica- tions. It has the functions of touchscreen interaction and voice interaction.
Note: Please check the version number of your ESP32-S3-LCD-EV-Board-MB indicated by the silk marking on the back. For boards of the v1.5 version, please refer to ESP32-S3-LCD-EV-Board v1.5. For boards of the v1.4 and below versions, please refer to ESP32-S3-LCD-EV-Board v1.4. Unless otherwise stated, the ESP32-S3-LCD-EV-Board in this document refers to both ESP32-S3-LCD-EV-Board and ESP32-S3-LCD-EV-Board-2.
3.1 ESP32-S3-LCD-EV-Board v1.5
Note: Please check the version number of your ESP32-S3-LCD-EV-Board-MB indicated by the silk marking on the back. For boards of the v1.5 version, please refer to this user guide. For boards of the v1.4 and below versions, please refer to ESP32-S3-LCD-EV-Board v1.4. Unless otherwise stated, the ESP32-S3-LCD-EV-Board in this document refers to both ESP32-S3-LCD-EV-Board and ESP32-S3-LCD-EV-Board-2.
This user guide will help you get started with ESP32-S3-LCD-EV-Board and will also provide more in-depth infor- mation. The document consists of the following sections: • Board Overview: Overview of the board hardware/software. • Start Application Development: How to set up hardware/software to develop applications. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: This is the first revision of this board released. • Sample Request: How to get a sample board. • Related Documents: Links to related documentation.
3.1.1 Board Overview
ESP32-S3-LCD-EV-Board is an ESP32-S3-based development board with a touchscreen. Together with different subboards, ESP32-S3-LCD-EV-Board can drive LCDs with IIC, SPI, 8080, and RGB interfaces. It houses dual array
31
Chapter 3. ESP32-S3-LCD-EV-Board
microphones, supports voice recognition and near/far-field voice wake-up, and features screen and voice interaction. The board caters to development needs for touchscreen products with different resolutions and interfaces. Currently, we have two boards available: • ESP32-S3-LCD-EV-Board with 480x480 LCD • ESP32-S3-LCD-EV-Board-2 with 800x480 LCD
Fig. 1: ESP32-S3-LCD-EV-Board with 480x480 LCD
Feature List
The main features of the board are listed below: • Module Embedded: ESP32-S3-WROOM-1 module with 16 MB flash and 16 MB PSRAM • Display: Compatibility with various subboards and support for displays with RGB, 8080, SPI, and I2C interfaces. Please refer to LCD Subboards for more information • Audio: Audio Codec + ADC amplifier and dual microphones • USB: USB to serial port chip plus USB Type-C download/debug
Block Diagram
The block diagram below shows the components of ESP32-S3-LCD-EV-Board and their interconnections.
Espressif Systems 32 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 2: ESP32-S3-LCD-EV-Board-2 with 800x480 LCD
Fig. 3: ESP32-S3-LCD-EV-Board Block Diagram (Click to Enlarge)
Espressif Systems 33 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Description of Components
The ESP32-S3-LCD-EV-Board consists of a mainboard and a subboard (see LCD Subboards for options). Addition- ally, it allows for a selection of a USB Type-A adapter.
Mainboard ESP32-S3-LCD-EV-Board-MB is the core of the kit, which integrates the ESP32-S3-WROOM-1 module and provides ports for connection to the LCD subboard.
Fig. 4: ESP32-S3-LCD-EV-Board-MB - Front (Click to Enlarge)
The key components of the board are described in a counter-clockwise direction.
Espressif Systems 34 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Key Component Description ESP32-S3-WROOM-1- ESP32-S3-WROOM-1-N16R16V is a generic Wi-Fi + Bluetooth LE MCU N16R16V Module module that is built around the ESP32-S3 series of SoCs. It is integrated with 16 MB flash and 16 MB PSRAM. On top of a rich set of peripherals, the accel- eration for neural network computing and signal processing workloads provided by the SoC makes the module an ideal choice for a wide variety of application scenarios related to Artificial Intelligence of Things (AIoT). Reset Button Press this button to reset the system. Boot Button Holding down the Boot key and momentarily pressing the Reset key initiates the firmware upload mode. Then you can upload firmware through the serial port or USB. Expansion Connector Provides connections for all I/O expander pins, all power supply pins, and some module pins. I/O Expander TCA9554 is a device that provides 8 bits of general purpose parallel I/O ex- pansion. It controls the I/O mode and level via two-line bidirectional I2C bus, offering a simple solution when additional I/Os are needed. LCD Board Connector Three different types of LCD subboards can be connected via connectors with 2.54 mm pitch. LED Supports configuring the RGB LED display to indicate status or behavior. USB-to-USB Port Provides power to the entire system (choose either USB-to-USB or USB-to- UART port). It is recommended to use at least a 5V/2A power adapter to ensure stable power supply. Used for USB communication between the PC and the ESP32-S3-WROOM-1 module. USB-to-UART Port Provides power to the entire system (choose either USB-to-USB or USB-to- UART port). It is recommended to use at least a 5V/2A power adapter to ensure stable power supply. Used for serial communication between the PC side and the ESP32-S3-WROOM-1 module. Left Microphone On-board microphone, connected to Audio ADC Chip. Right Microphone On-board microphone, connected to Audio ADC Chip. Audio ADC Chip ES7210 is a high performance, low power 4-channel audio ADC for applica- tions of microphone arrays. Featuring Acoustic Echo Cancellation (AEC), it is an ideal choice for music and voice applications. USB-to-UART Bridge Con- CP2102N, the single-chip USB-to-UART bridge controller, provides up to 3 troller Mbps connection for software download and debugging. Audio Codec Chip ES8311 is a low-power mono audio codec that includes a single-channel ADC and DAC, low noise pre-amplifier, headphone driver, digital audio, analog mix- ing, and gain function. It connects to the ESP32-S3-WROOM-1 module via I2S and I2C buses to process audio through hardware instead of the audio ap- plication. Audio Amplifier NS4150 is a low EMI, 3 W mono class D audio amplifier used to drive speakers by amplifying the audio signal from the audio codec chip. Speaker Connector External speaker playback is possible with the help of the audio amplifier.
LCD Subboards The mainboard can be used together with three different kinds of subboards:
Espressif Systems 35 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Board Name Dis- Reso- LCD Driver Touch Available Development play lution (Interface) Driver Boards (Inch) (Px) ESP32-S3-LCD-EV-Board- 0.96 128 x SSD1315 N/A Not Available SUB1 v1.0 64 (I2C) 2.40 320 x ST7789V XTP2046 Not Available 240 (SPI) ESP32-S3-LCD-EV-Board- 3.50 480 x ST7796S GT911 Not Available SUB2 v1.5 320 (8080) 3.95 480 x GC9503CV FT5x06 ESP32-S3-LCD-EV-Board 480 (RGB) ESP32-S3-LCD-EV-Board- 4.30 800 x ST7262E43 GT1151 ESP32-S3-LCD-EV-Board-2 SUB3 v1.3 480 (RGB)
• ESP32-S3-LCD-EV-Board-SUB1 subboard has two interfaces, which support connection to a 2.4-inch dis- play with the SPI interface or a 0.96-inch display with the I2C interface. This board is not yet configured, so it is not further explained here. • ESP32-S3-LCD-EV-Board-SUB2 subboard has two interfaces, which support connection to a display with the RGB interface or a display with the 8080 parallel interface. The current subboard has a 3.95-inch touch- screen with the RGB565 interface and 480x480 resolution. The LCD driver IC is GC9503CV and the touch- screen driver IC is FT5x06.
Fig. 5: ESP32-S3-LCD-EV-Board-SUB2 - Front (Click to Enlarge)
• ESP32-S3-LCD-EV-Board-SUB3 subboard only supports a 4.3-inch touchscreen with the RGB565 interface
Espressif Systems 36 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 6: ESP32-S3-LCD-EV-Board-SUB2 - Back (Click to Enlarge)
and 800x480 resolution. The LCD driver IC is ST7262E43 and the touchscreen driver IC is GT1151.
USB Type-A Adapter With the USB Type-A adapter, the mainboard can serve as a USB host for connection to USB devices.
Application Examples
The following application examples are available for ESP32-S3-LCD-EV-Board v1.5: • 86-box Demo Example - Demonstrates a GUI demo designed for a control panel (480x480) typically used for wall-mounted 86 type box, providing a smooth graphic operation experience with features like weather report, hot water heater, warm air heater page, and audio output function. • 86-box Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice recognition function, providing a reference for flashing the board and troubleshooting potential issues. • LVGL Demos Example - Demonstrates how to run LVGL s demos on an ESP32-S3-LCD-EV-Board, show- casing three methods to avoid tearing effect using different buffering modes, and providing performance testing results for different buffering modes. • Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice recognition function, providing instructions on how to flash the example to the ESP32-S3-LCD-EV-Board and configure it for use. • USB Camera LCD Example - Demonstrates how to use an LCD display to show video captured from a USB camera, with options to transfer frames to Wi-Fi and log memory information, providing a basis for developing applications with ESP32-S3-LCD-EV-Board. • USB File System - Demonstrates how to use USB HOST on ESP32-S2/ESP32-S3 to read and write files on a USB flash drive, displaying its contents on the screen, with support for various file formats for preview. • USB Keyboard Example - Demonstrates how to use LCD and LVGL to simulate a USB keyboard on the ESP32-S3-LCD-EV-Board, providing a GUI of a USB keyboard that can interact with a PC like a real key-
Espressif Systems 37 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 7: ESP32-S3-LCD-EV-Board-SUB3 - Front (Click to Enlarge)
Espressif Systems 38 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 8: ESP32-S3-LCD-EV-Board-SUB3 - Back (Click to Enlarge)
Fig. 9: USB Type-A Adapter v1.1 - Front (Click to Enlarge)
Espressif Systems 39 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 10: USB Type-A Adapter v1.1 - Connected to the Mainboard (Click to Enlarge)
Fig. 11: USB Type-A Adapter v1.1 - Connected to USB Devices (Click to Enlarge)
Espressif Systems 40 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
board.
For more examples and the latest updates, please refer to the examples folder. To explore the application examples or to develop your own, please follow the steps outlined in the Start Application Development section.
3.1.2 Start Application Development
This section provides instructions on how to do hardware and software setup and flash firmware onto the board to develop your own application.
Required Hardware
• 1 x ESP32-S3-LCD-EV-Board-MB
• 1 x LCD subboard
• 1 x USB 2.0 cable (standard Type-A to Type-C)
• 1 x PC (Windows, Linux, or macOS)
Note: Please make sure to use the appropriate USB cable. Some cables can only be used for charging, not for data transfer or program flashing.
Optional Hardware • 1 x Speaker
Hardware Setup
Prepare the board for loading of the first sample application:
- Connect the LCD subboard to the LCD Board Connector.
- Plug in the USB cable to connect the PC with the board.
- The LCD lights up and you can start to interact with it. Now the board is ready for software setup.
Software Setup
The development framework of ESP32-S3-LCD-EV-Board is ESP-IDF. ESP-IDF is a FreeRTOS-based SoC devel- opment framework with a bunch of components including LCD, ADC, RMT, and SPI. To learn how to quickly set up your development environment, please go to Get Started > Installation.
Note: • ESP-IDF v5.1.2 is required. It is recommended to use the latest release/v5.1 branch for development. • For more information about developing LCD applications, please refer to ESP-IoT-Solution Programming Guide.
3.1.3 Hardware Reference
This section provides more detailed information about the board s hardware.
Espressif Systems 41 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
GPIO Allocation
The table below provides the allocation of GPIOs exposed on terminals of ESP32-S3-WROOM-1 module to control specific components or functions of the board.
Table 1: ESP32-S3-WROOM-1 GPIO Allocation
Pin Pin Name Function 1 GND GND 2 3V3 Power supply 3 EN RESET 4 IO4 LED 5 IO5 I2S_MCLK 6 IO6 I2S_CODEC_DSDIN 7 IO7 I2S_LRCK 8 IO15 I2S_ADC_SDOUT 9 IO16 I2S_SCLK 10 IO17 LCD_DE 11 IO18 LCD_DATA7 12 IO8 LCD_DATA6 13 IO19 USB_D- 14 IO20 USB_D+ 15 IO3 LCD_VSYNC 16 IO46 LCD_HSYNC 17 IO9 LCD_PCLK 18 IO10 LCD_DATA0 19 IO11 LCD_DATA1 20 IO12 LCD_DATA2 21 IO13 LCD_DATA3 22 IO14 LCD_DATA4 23 IO21 LCD_DATA5 24 IO47 I2C_SDA 25 IO48 I2C_SCL 26 IO45 LCD_DATA8 27 IO0 BOOT 28 IO35 No connection 29 IO36 No connection 30 IO37 No connection 31 IO38 LCD_DATA9 32 IO39 LCD_DATA10 33 IO40 LCD_DATA11 34 IO41 LCD_DATA12 35 IO42 LCD_DATA13 36 RXD0 UART_RXD0 37 TXD0 UART_TXD0 38 IO2 LCD_DATA14 39 IO1 LCD_DATA15 40 GND GND 41 EPAD GND
The pins on the I/O expander connected to the module can be used for different functions.
Espressif Systems 42 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Table 2: I/O Expander GPIO Allocation
IO Expander Pin Pin Name Function 1 A0 GND 2 A1 GND 3 A2 GND 4 P0 PA_CTRL 5 P1 LCD_SPI_CS 6 P2 LCD_SPI_SCK 7 P3 LCD_SPI_MOSI 8 GND GND 9 P4 Free 10 P5 Free 11 P6 Free 12 P7 Free 13 INT No connection 14 SCL I2C_SCL 15 SDA I2C_SDA 16 VCC Supply voltage
Power Distribution
Power Supply over USB There are two ways to power the development board via USB power port. • Via USB-to-USB port
Fig. 12: ESP32-S3-LCD-EV-Board - USB-to-USB Power Supply
• Via USB-to-UART port
Independent Audio and Digital Power Supply ESP32-S3-LCD-EV-Board features independent power supplies for the audio components and ESP module. This should reduce noise in the audio signal from digital components and improve the overall performance of the components.
AEC Path
The acoustic echo cancellation (AEC) path provides reference signals for AEC algorithm.
Espressif Systems 43 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 13: ESP32-S3-LCD-EV-Board - USB-to-UART Power Supply
Fig. 14: ESP32-S3-LCD-EV-Board - Digital Power Supply
Fig. 15: ESP32-S3-LCD-EV-Board - Audio Power Supply
Espressif Systems 44 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
ESP32-S3-LCD-EV-Board provides two compatible echo reference signal source designs. One is Codec (ES8311) DAC output (DAC_AOUTLP/DAC_AOUTLP), the other is PA (NS4150) output (PA_OUT+/PA_OUT+). The former is a default and the recommended selection. Resistors R54 and R56 shown in the figure below should not be installed. The echo reference signal is collected by ADC_MIC3P/ADC_MIC3N of ADC (ES7210) and then sent back to ESP32-S3 for AEC algorithm.
Fig. 16: ESP32-S3-LCD-EV-Board - AEC Codec DAC Output (Click to Enlarge)
Hardware Setup Options
Automatic Download There are two ways to put the development board into the download mode. • Press the Boot and Reset buttons. Release the Reset button first and then the Boot button. • The download is performed automatically by the software. The software uses the DTR and RTS signals from the serial port to control the status of the EN and IO0 pins.
3.1.4 Hardware Revision Details
ESP32-S3-LCD-EV-Board v1.5
• The following pins are re-allocated for the ESP32-S3-WROOM-1-N16R16V module: – I2C_SCL: from IO18 to IO48 – I2C_SDA: from IO8 to IO47 – LCD_DATA6: from IO47 to IO8 – LCD_DATA7: from IO48 to IO18 • Level-shifting circuits are added to IO47 and IO48 for converting the 1.8 V logic level to a 3.3 V logic level.
ESP32-S3-LCD-EV-Board v1.4
• Initial Release
3.1.5 Sample Request
This development board with the USB Type-A adapter is suitable for evaluating Espressif s high-performance HMI Smart Displays Solution. For placing orders, please proceed to the Espressif Online Shop.
Espressif Systems 45 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 17: SP32-S3-LCD-Ev-Board - AEC PA Output (Click to Enlarge)
Fig. 18: ESP32-S3-LCD-EV-Board - AEC Reference Signal Collection (Click to Enlarge)
Espressif Systems 46 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
3.1.6 Related Documents
Please download the following documents from the HTML version of esp-dev-kits Documentation. • ESP32-S3 Datasheet • ESP32-S3-WROOM-1 Datasheet • ESP Product Selector • ESP32-S3-LCD-EV-Board-MB Schematics • ESP32-S3-LCD-EV-Board-MB PCB Layout • ESP32-S3-LCD-EV-Board-SUB1 Schematics • ESP32-S3-LCD-EV-Board-SUB1 PCB Layout • ESP32-S3-LCD-EV-Board-SUB2 Schematics • ESP32-S3-LCD-EV-Board-SUB2 PCB Layout • 3.95_480x480_RGB_Display Specification • ESP32-S3-LCD-EV-Board-SUB3 Schematics • ESP32-S3-LCD-EV-Board-SUB3 PCB Layout • ESP32-S3-LCD-EV-Board USB Adapter Schematics • ESP32-S3-LCD-EV-Board USB Adapter PCB Layout • ESP32-S3-LCD-EV-Board Reference Design • TCA9554 Datasheet • 4.3_800x480_RGB_Display Specification For further design documentation for the board, please contact us at sales@espressif.com.
ESP32-S3-LCD-EV-Board v1.4
Note: Please check the version number of your ESP32-S3-LCD-EV-Board-MB indicated by the silk marking on the back. For boards of the v1.4 and below versions, please refer to this user guide. For boards of the v1.5 version, please refer to ESP32-S3-LCD-EV-Board v1.5. Unless otherwise stated, the ESP32-S3-LCD-EV-Board in this document refers to both ESP32-S3-LCD-EV-Board and ESP32-S3-LCD-EV-Board-2.
This user guide will help you get started with ESP32-S3-LCD-EV-Board and will also provide more in-depth infor- mation. The document consists of the following sections: • Board Overview: Overview of the board hardware/software. • Start Application Development: How to set up hardware/software to develop applications. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: This is the first revision of this board released. • Sample Request: How to get a sample board. • Related Documents: Links to related documentation.
Board Overview ESP32-S3-LCD-EV-Board is an ESP32-S3-based development board with a touchscreen. To- gether with different subboards, ESP32-S3-LCD-EV-Board can drive LCDs with IIC, SPI, 8080, and RGB inter- faces. It houses dual array microphones, supports voice recognition and near/far-field voice wake-up, and features screen and voice interaction. The board caters to development needs for touchscreen products with different resolu- tions and interfaces. Currently, we have two boards available: • ESP32-S3-LCD-EV-Board with 480x480 LCD • ESP32-S3-LCD-EV-Board-2 with 800x480 LCD
Espressif Systems 47 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 19: ESP32-S3-LCD-EV-Board with 480x480 LCD
Espressif Systems 48 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 20: ESP32-S3-LCD-EV-Board-2 with 800x480 LCD
Espressif Systems 49 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Feature List The main features of the board are listed below: • Module Embedded: ESP32-S3-WROOM-1 module with 16 MB flash and 8 MB PSRAM • Display: Compatibility with various subboards and support for displays with RGB, 8080, SPI, and I2C interfaces. Please refer to LCD Subboards for more information • Audio: Audio Codec + ADC amplifier and dual microphones • USB: USB to serial port chip plus USB Type-C download/debug
Block Diagram The block diagram below shows the components of ESP32-S3-LCD-EV-Board and their inter- connections.
Fig. 21: ESP32-S3-LCD-EV-Board Block Diagram (Click to Enlarge)
Description of Components The ESP32-S3-LCD-EV-Board development board consists of a mainboard and a subboard (see LCD Subboards for options). Additionally, it allows for a selection of a USB Type-A adapter.
Mainboard ESP32-S3-LCD-EV-Board-MB is the core of the kit, which integrates the ESP32-S3-WROOM-1 module and provides ports for connection to the LCD subboard. The key components of the board are described in a counter-clockwise direction.
Espressif Systems 50 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 22: ESP32-S3-LCD-EV-Board-MB - Front (Click to Enlarge)
Espressif Systems 51 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Key Component Description ESP32-S3-WROOM-1- ESP32-S3-WROOM-1-N16R8 is a generic Wi-Fi + Bluetooth LE MCU mod- N16R8 Module ule that is built around the ESP32-S3 series of SoCs. It is integrated with 16 MB flash and 8 MB PSRAM. On top of a rich set of peripherals, the acceler- ation for neural network computing and signal processing workloads provided by the SoC makes the module an ideal choice for a wide variety of application scenarios related to Artificial Intelligence of Things (AIoT). Reset Button Press this button to reset the system. Boot Button Holding down the Boot key and momentarily pressing the Reset key initiates the firmware upload mode. Then you can upload firmware through the serial port or USB. Expansion Connector Provides connections for all I/O expander pins, all power supply pins, and some module pins. I/O Expander TCA9554 is a device that provides 8 bits of general purpose parallel I/O ex- pansion. It controls the I/O mode and level via two-line bidirectional I2C bus, offering a simple solution when additional I/Os are needed. LCD Board Connector Three different types of LCD subboards can be connected via connectors with 2.54 mm pitch. LED Supports configuring the RGB LED display to indicate status or behavior. USB-to-USB Port Provides power to the entire system (choose either USB-to-USB or USB-to- UART port). It is recommended to use at least a 5V/2A power adapter to ensure stable power supply. Used for USB communication between the PC and the ESP32-S3-WROOM-1 module. USB-to-UART Port Provides power to the entire system (choose either USB-to-USB or USB-to- UART port). It is recommended to use at least a 5V/2A power adapter to ensure stable power supply. Used for serial communication between the PC side and the ESP32-S3-WROOM-1 module. Left Microphone On-board microphone, connected to Audio ADC Chip. Right Microphone On-board microphone, connected to Audio ADC Chip. Audio ADC Chip ES7210 is a high performance, low power 4-channel audio ADC for applica- tions of microphone arrays. Featuring Acoustic Echo Cancellation (AEC), it is an ideal choice for music and voice applications. USB-to-UART Bridge Con- CP2102N, the single-chip USB-to-UART bridge controller, provides up to 3 troller Mbps connection for software download and debugging. Audio Codec Chip ES8311 is a low-power mono audio codec that includes a single-channel ADC and DAC, low noise pre-amplifier, headphone driver, digital audio, analog mix- ing, and gain function. It connects to the ESP32-S3-WROOM-1 module via I2S and I2C buses to process audio through hardware instead of the audio ap- plication. Audio Amplifier NS4150 is a low EMI, 3 W mono class D audio amplifier used to drive speakers by amplifying the audio signal from the audio codec chip. Speaker Connector External speaker playback is possible with the help of the audio amplifier.
LCD Subboards The mainboard can be used together with three different kinds of subboards:
Espressif Systems 52 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Board Name Dis- Reso- LCD Driver Touch Available Development play lution (Interface) Driver Boards (Inch) (Px) ESP32-S3-LCD-EV-Board- 0.96 128 x SSD1315 Not Not Available SUB1 v1.0 64 (I2C) Avail- able 2.40 320 x ST7789V XTP2046 Not Available 240 (SPI) ESP32-S3-LCD-EV-Board- 3.50 480 x ST7796S GT911 Not Available SUB2 v1.4 320 (8080) 3.95 480 x GC9503CV FT5x06 ESP32-S3-LCD-EV-Board 480 (RGB) ESP32-S3-LCD-EV-Board- 4.30 800 x ST7262E43 GT1151 ESP32-S3-LCD-EV-Board-2 SUB3 v1.3 480 (RGB)
• The ESP32-S3-LCD-EV-Board-SUB1 subboard has two interfaces, which support connection to a 2.4-inch display with the SPI interface or a 0.96-inch display with the I2C interface. This board is not yet configured, so it is not further explained here. • The ESP32-S3-LCD-EV-Board-SUB2 subboard has two interfaces, which support connection to a display with the RGB interface or a display with the 8080 parallel interface. The current subboard has a 3.95-inch touchscreen with the RGB565 interface and 480x480 resolution. The LCD driver IC is GC9503CV and the touchscreen driver IC is FT5x06.
Fig. 23: ESP32-S3-LCD-EV-Board-SUB2 - Front (Click to Enlarge)
Espressif Systems 53 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 24: ESP32-S3-LCD-EV-Board-SUB2 - Back (Click to Enlarge)
• The ESP32-S3-LCD-EV-Board-SUB3 subboard only supports a 4.3-inch touchscreen with the RGB565 interface and 800x480 resolution. The LCD driver IC is ST7262E43 and the touchscreen driver IC is GT1151.
USB Type-A Adapter With the USB Type-A adapter, the mainboard can serve as a USB host for connection to USB devices.
Application Examples The following application examples are available for ESP32-S3-LCD-EV-Board v1.4: • 86-box Demo Example - Demonstrates a GUI demo designed for a control panel (480x480) typically used for wall-mounted 86 type box, providing a smooth graphic operation experience with features like weather report, hot water heater, warm air heater page, and audio output function. • 86-box Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice recognition function, providing a reference for flashing the board and troubleshooting potential issues. • LVGL Demos Example - Demonstrates how to run LVGL s demos on an ESP32-S3-LCD-EV-Board, show- casing three methods to avoid tearing effect using different buffering modes, and providing performance testing results for different buffering modes. • Smart Panel Example - Demonstrates a factory demo for a smart control panel with offline voice recognition function, providing instructions on how to flash the example to the ESP32-S3-LCD-EV-Board and configure it for use. • USB Camera LCD Example - Demonstrates how to use an LCD display to show video captured from a USB camera, with options to transfer frames to Wi-Fi and log memory information, providing a basis for developing applications with ESP32-S3-LCD-EV-Board. • USB File System - Demonstrates how to use USB HOST on ESP32-S2/ESP32-S3 to read and write files on a USB flash drive, displaying its contents on the screen, with support for various file formats for preview. • USB Keyboard Example - Demonstrates how to use LCD and LVGL to simulate a USB keyboard on the ESP32-S3-LCD-EV-Board, providing a GUI of a USB keyboard that can interact with a PC like a real key- board.
Espressif Systems 54 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 25: ESP32-S3-LCD-EV-Board-SUB3 - Front (Click to Enlarge)
Fig. 26: ESP32-S3-LCD-EV-Board-SUB3 - Back (Click to Enlarge)
Espressif Systems 55 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 27: USB Type-A Adapter v1.1 - Front (Click to Enlarge)
Fig. 28: USB Type-A Adapter v1.1 - Connected to the Mainboard (Click to Enlarge)
Espressif Systems 56 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 29: USB Type-A Adapter v1.1 - Connected to USB Devices (Click to Enlarge)
For more examples and the latest updates, please refer to the examples folder. To explore the application examples or to develop your own, please follow the steps outlined in the Start Application Development section.
Start Application Development This section provides instructions on how to do hardware and software setup and flash firmware onto the board to develop your own application.
Required Hardware • 1 x ESP32-S3-LCD-EV-Board-MB • 1 x LCD subboard • 1 x USB 2.0 cable (standard Type-A to Type-C) • 1 x PC (Windows, Linux, or macOS)
Note: Please make sure to use the appropriate USB cable. Some cables can only be used for charging, not for data transfer or program flashing.
Optional Hardware • 1 x Speaker
Hardware Setup Prepare the board for loading of the first sample application:
- Connect the LCD subboard to the LCD Board Connector.
- Plug in the USB cable to connect the PC with the board.
- The LCD lights up and you can start to interact with it. Now the board is ready for software setup.
Espressif Systems 57 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Software Setup The development framework of ESP32-S3-LCD-EV-Board is ESP-IDF. ESP-IDF is a FreeRTOS-based SoC development framework with a bunch of components including LCD, ADC, RMT, and SPI. To learn how to quickly set up your development environment, please go to Get Started > Installation.
Note: • ESP-IDF v5.1.2 is required. It is recommended to use the latest release/v5.1 branch for development. • For more information about developing LCD applications, please refer to ESP-IoT-Solution Programming Guide.
Hardware Reference This section provides more detailed information about the board s hardware.
GPIO Allocation The table below provides the allocation of GPIOs exposed on terminals of ESP32-S3-WROOM- 1 module to control specific components or functions of the board.
Table 3: ESP32-S3-WROOM-1 GPIO Allocation
Pin Pin Name Function 1 GND GND 2 3V3 Power supply 3 EN RESET 4 IO4 LED 5 IO5 I2S_MCLK 6 IO6 I2S_CODEC_DSDIN 7 IO7 I2S_LRCK 8 IO15 I2S_ADC_SDOUT 9 IO16 I2S_SCLK 10 IO17 LCD_DE 11 IO18 I2C_SCL 12 IO8 I2C_SDA 13 IO19 USB_D- 14 IO20 USB_D+ 15 IO3 LCD_VSYNC 16 IO46 LCD_HSYNC 17 IO9 LCD_PCLK 18 IO10 LCD_DATA0 19 IO11 LCD_DATA1 20 IO12 LCD_DATA2 21 IO13 LCD_DATA3 22 IO14 LCD_DATA4 23 IO21 LCD_DATA5 24 IO47 LCD_DATA6 25 IO48 LCD_DATA7 26 IO45 LCD_DATA8 27 IO0 BOOT 28 IO35 No connection 29 IO36 No connection 30 IO37 No connection 31 IO38 LCD_DATA9 32 IO39 LCD_DATA10 33 IO40 LCD_DATA11 34 IO41 LCD_DATA12 35 IO42 LCD_DATA13 36 RXD0 UART_RXD0 continues on next page
Espressif Systems 58 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Table 3 – continued from previous page
Pin Pin Name Function 37 TXD0 UART_TXD0 38 IO2 LCD_DATA14 39 IO1 LCD_DATA15 40 GND GND 41 EPAD GND
The pins on the I/O expander connected to the module can be used for different functions.
Table 4: I/O Expander GPIO Allocation
IO Expander Pin Pin Name Function 1 A0 GND 2 A1 GND 3 A2 GND 4 P0 PA_CTRL 5 P1 LCD_SPI_CS 6 P2 LCD_SPI_SCK 7 P3 LCD_SPI_MOSI 8 GND GND 9 P4 Free 10 P5 Free 11 P6 Free 12 P7 Free 13 INT No connection 14 SCL I2C_SCL 15 SDA I2C_SDA 16 VCC Supply voltage
Power Distribution
Power Supply over USB There are two ways to power the development board via USB power port. • Via USB-to-USB port
Fig. 30: ESP32-S3-LCD-EV-Board - USB-to-USB Power Supply
Espressif Systems 59 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
• Via USB-to-UART port
Fig. 31: ESP32-S3-LCD-EV-Board - USB-to-UART Power Supply
Independent Audio and Digital Power Supply ESP32-S3-LCD-EV-Board features independent power supplies for the audio components and ESP module. This should reduce noise in the audio signal from digital components and improve the overall performance of the components.
Fig. 32: ESP32-S3-LCD-EV-Board - Digital Power Supply
AEC Path The acoustic echo cancellation (AEC) path provides reference signals for AEC algorithm. ESP32-S3-LCD-EV-Board provides two compatible echo reference signal source designs. One is Codec (ES8311) DAC output (DAC_AOUTLP/DAC_AOUTLP), the other is PA (NS4150) output (PA_OUT+/PA_OUT+). The former is a default and the recommended selection. Resistors R54 and R56 shown in the figure below should not be installed. The echo reference signal is collected by ADC_MIC3P/ADC_MIC3N of ADC (ES7210) and then sent back to ESP32-S3 for AEC algorithm.
Hardware Setup Options
Espressif Systems 60 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 33: ESP32-S3-LCD-EV-Board - Audio Power Supply
Fig. 34: ESP32-S3-LCD-EV-Board - AEC Codec DAC Output (Click to Enlarge)
Espressif Systems 61 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Fig. 35: SP32-S3-LCD-Ev-Board - AEC PA Output (Click to Enlarge)
Fig. 36: ESP32-S3-LCD-EV-Board - AEC Reference Signal Collection (Click to Enlarge)
Espressif Systems 62 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Automatic Download There are two ways to put the development board into the download mode. • Press the Boot and Reset buttons. Release the Reset button first and then the Boot button. • The download is performed automatically by the software. The software uses the DTR and RTS signals from the serial port to control the status of the EN and IO0 pins.
Hardware Revision Details No previous revisions.
Sample Request This development board with the USB Type-A adapter is suitable for evaluating Espressif s high-performance HMI Smart Displays Solution. For placing orders, please proceed to the Espressif Online Shop.
Related Documents Please download the following documents from the HTML version of esp-dev-kits Documen- tation. • ESP32-S3 Datasheet • ESP32-S3-WROOM-1 Datasheet • ESP Product Selector • ESP32-S3-LCD-EV-Board-MB Schematics • ESP32-S3-LCD-EV-Board-MB PCB Layout • ESP32-S3-LCD-EV-Board-SUB1 Schematics • ESP32-S3-LCD-EV-Board-SUB1 PCB Layout • ESP32-S3-LCD-EV-Board-SUB2 Schematics • ESP32-S3-LCD-EV-Board-SUB2 PCB Layout • ESP32-S3-LCD-EV-Board-SUB3 Schematics • ESP32-S3-LCD-EV-Board-SUB3 PCB Layout • ESP32-S3-LCD-EV-Board USB Adapter Schematics • ESP32-S3-LCD-EV-Board USB Adapter PCB Layout • TCA9554 Datasheet For further design documentation for the board, please contact us at sales@espressif.com.
Espressif Systems 63 Release master Submit Document Feedback
Chapter 3. ESP32-S3-LCD-EV-Board
Espressif Systems 64 Release master Submit Document Feedback
Chapter 4
ESP-VoCat
ESP-VoCat is an intelligent AI development kit. It is suitable for voice interaction products that require large model capabilities, such as toys, smart speakers, and smart central control systems. The device is equipped with an ESP32- S3 module, a 1.85-inch QSPI circular touch screen, dual microphone array, and supports offline voice wake-up and sound source localization algorithms. Combined with the large model capabilities provided by OpenAI Xiaozhi AI, Gemini, etc., ESP-VoCat can achieve full-duplex voice interaction, multimodal recognition, and intelligent agent control, providing a solid foundation for developers to create complete edge-side AI application experiences. Application examples for the development board are stored in the esp-brookesia project.
Note: Please check the silkscreen version number on the mainboard to confirm your development board version. For v1.0 version development boards, please refer to ESP-VoCat v1.0; for v1.2 version development boards, please refer to ESP-VoCat v1.2.
Tip: For quick-start procedures after powering on ESP-VoCat, refer to the ESP-VoCat Built-in Firmware User Guide.
4.1 ESP-VoCat v1.2
Note: Please check the silkscreen version number on the mainboard to confirm your development board version. For v1.0 version development boards, please refer to ESP-VoCat v1.0; For v1.2 version development boards, please refer to the current user guide.
Tip: For quick-start procedures after powering on ESP-VoCat, refer to the ESP-VoCat Built-in Firmware User Guide.
This guide will help you get started with ESP-VoCat quickly and provide detailed information about this development board. ESP-VoCat is an intelligent AI development kit. It is suitable for voice interaction products that require large model capabilities, such as toys, smart speakers, and smart central control systems. The device is equipped with an ESP32- S3-WROOM-1 module, a 1.85-inch QSPI circular touch screen, dual microphone array, and supports offline voice wake-up and sound source localization algorithms. Combined with the large model capabilities provided by Amazon
65
Chapter 4. ESP-VoCat
Nova, OpenAI, Xiaozhi AI, Gemini, etc. ESP-VoCat can achieve full-duplex voice interaction, multimodal recog- nition, and intelligent agent control, providing a solid foundation for developers to create complete edge-side AI application experiences. ESP-VoCat s main controller uses the Espressif ESP32-S3-WROOM-1-N16R16VA module, supporting 2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity. For storage, the entire device has 16MB PSRAM and 16MB Flash storage space, and is also equipped with a microSD card slot that can support up to 32GB, meeting the needs of voice interaction and multimedia processing. It features a 1.85-inch circular touch screen (360 × 360 resolution) with ESP32-S3 native touch sensors, providing an intuitive and rich interactive experience. For audio, ESP-VoCat has a built-in 3W speaker and dual microphone array, supporting local voice wake-up and sound source localization. The power system is compatible with 5 V DC and 3.7 V lithium battery power supply. Additionally, it integrates a USB-C interface for power supply and programming download, while reserving a Pogopin interface for convenient functional expansion.
Fig. 1: ESP-VoCat Front View (Click to enlarge)
The document consists of the following major sections: • Getting Started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: Hardware revision history and known issues (if any) of the board. • Related Documents: Links to related documentation.
4.1.1 Getting Started
This section provides a brief introduction of ESP-VoCat, instructions on how to do the initial hardware setup and how to flash firmware onto it.
Description of Components
The following introduces the main components on the front PCB in clockwise order. For user convenience, we have also labeled these components or interfaces on the ESP-VoCat housing.
Espressif Systems 66 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 2: ESP-VoCat Back View (Click to enlarge)
Fig. 3: ESP-VoCat CoreBoard PCB Front View (Click to enlarge)
Espressif Systems 67 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 4: ESP-VoCat MicBoard PCB Front View (Click to enlarge)
Fig. 5: ESP-VoCat BaseBoard PCB Front View (Click to enlarge)
Espressif Systems 68 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 6: ESP-VoCat Front View (Click to enlarge)
Main Components Description CoreBoard ESP32-S3-WROOM-1- Main controller chip, integrates 16 MB Flash and 16 MB PSRAM, supports N16R16VA 2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity. Battery Connector Battery connector for connecting 3.7 V lithium battery, top is positive, bottom is negative. LCD FPC Connector For connecting 1.85-inch circular LCD screen with 360 x 360 resolution. For detailed parameters, please refer to the Display Specification. MicBoard Connector MicBoard PCB connector, connects dual microphone array and status indicator LED. Touch Connector Touch connector for connecting touch copper foil to achieve touch interaction functionality. Speaker Connector 2-wire speaker connector for connecting built-in 3 W speaker. MicBoard Green LED Green LED indicator. MIC (Microphone Array) Dual LMA3729T381-OY3S microphone array, supports local voice wake-up and sound source localization functionality. BaseBoard BQ27220 (Battery Manage- Battery management chip for battery level detection, charging management, ment Chip) and power status monitoring. TP4057 (Lithium Battery Lithium battery charging chip for charging lithium batteries with 250 mA Charging Chip) charging current. CoreBoard Connector CoreBoard PCB connector, connects core board with base board. TlV62569 (DCDC Chip) Buck converter chip for converting 5 V power to 3.3 V power, providing stable power supply for the system. SAM8108 (Power Control Power control chip for controlling device power on/off. Single click of POWER Chip) button can toggle power on/off status. Type-C (USB-C Interface) USB-C interface for power supply, programming download, and debugging, supports charging lithium batteries. Espressif Systems 69 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 7: ESP-VoCat CoreBoard PCB Back View (Click to enlarge)
Fig. 8: ESP-VoCat MicBoard PCB Back View (Click to enlarge)
The following introduces the main components on the back PCB in clockwise order. For user convenience, we have also labeled these components or interfaces on the ESP-VoCat housing.
Espressif Systems 70 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 9: ESP-VoCat BaseBoard PCB Back View (Click to enlarge)
Fig. 10: ESP-VoCat Back View (Click to enlarge)
Espressif Systems 71 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Main Components Description CoreBoard NS4150B (Class D Amplifier) Ultra-low EMI, filterless, 3W mono Class D audio amplifier. ES7210 (Audio Decoder Chip) High-performance 4-channel audio decoder chip, supports I2S/PDM/TDM data ports. SY8088AAC (DCDC chip) Buck converter chip used to convert a 5 V power supply to a 3.3 V power supply, providing stable power for the Codec. BaseBoard Connector Base board connector for connecting base board with CoreBoard. BMI270 (IMU - Inertial Mea- 6-axis intelligent low-power inertial measurement unit for high-performance surement Unit) applications. ES8311 (Audio Codec Chip) Low-power mono audio codec with high-performance multi-bit Delta-Sigma audio ADC and DAC. MicBoard FPC Connector Connects MicBoard with CoreBoard FPC connector. BaseBoard M1.6 Welded Nut For fixing main board to housing. RST Button (Reset Button) For resetting the main board. Magnetic Connector For functional expansion, provides a serial port and 5 V power interface, can connect to rotating base and other devices. POWER Switch For controlling device power on/off. Single click of POWER button can toggle power on/off status. BOOT Button When powering on, hold this button to enter download mode. SD Card Slot Supports up to 32 GB microSD card slot for storing audio, images, videos, and other data.
Start Application Development
Before powering on, please ensure ESP-VoCat is intact and undamaged.
Required Hardware • ESP-VoCat • USB data cable • Computer (Windows, Linux, or macOS)
Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Hardware Setup Use a USB data cable to connect ESP-VoCat to your computer through the Type-C (USB-C Interface) for firmware burning, debugging, and power supply.
Software Setup Please proceed to ESP-IDF Get Started to set up the development environment and flash an ap- plication example onto your board.
Note: In most cases, USB drivers required to operate the board are already included in Windows, Linux, and macOS operating systems. Some additional port access or security configuration may be required depending on your OS. In case of issues, please check documentation on how to establish serial connection with the board. The documentation also includes links to USB drivers applicable to boards produced by Espressif.
Espressif Systems 72 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Espressif provides Board Support Packages (BSPs) for various Espressif boards that help you initialize and use key onboard peripherals, such as LCD displays, audio chips, buttons, and LEDs, more easily and efficiently. For a com- plete list of supported boards, please visit esp-bsp. Development board application examples are stored in the esp-brookesia project.
4.1.2 Hardware Reference
Block Diagram
The block diagram below shows the components of ESP-VoCat and their interconnections.
Fig. 11: ESP-VoCat Block Diagram (Click to enlarge)
Power Supply Options
There are three mutually exclusive ways to provide power to the board:
Power through Type-C (USB-C Interface) When using this method, connect the device s Type-C interface using a USB Type-C data cable. If a lithium battery is installed, you need to press the POWER button to enable power supply to the device.
Power through Magnetic Connector When using this method, connect the device to the corresponding magnetic connector base to power the device. If a lithium battery is installed, you need to press the POWER button to enable power supply to the device.
Power through Battery The device has an integrated 3.7 V lithium battery. Press the POWER button to power the device. Any of the above external power supply methods can charge the internal lithium battery.
Type-C Interface
Magnetic Connector Interface
Espressif Systems 73 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 12: Magnetic Connector (Click to enlarge)
Fig. 13: Type-C Interface Circuit Diagram (Click to enlarge)
Espressif Systems 74 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 14: Magnetic Connector Interface Circuit Diagram (Click to enlarge)
Fig. 15: LCD Interface Circuit Diagram (Click to enlarge)
Espressif Systems 75 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
LCD Interface
Please note that the CN3 interface is reserved for other screen compatibility and is currently not enabled. The U2 interface is the officially used LCD screen interface. The screen model used by this development board is ST77916, LCD: 1.85 , 360 x 360, ST77916, QSPI Interface. LCD_BLK (GPIO44) can be used to control screen backlight.
SD Card Interface
Fig. 16: SD Card Interface Circuit Diagram (Click to enlarge)
Please note that the SD card interface supports: • 1-wire SD bus configuration • Communication through SDIO protocol
Power Switch Circuit
Fig. 17: Power Switch Circuit Diagram (Click to enlarge)
Charging Circuit
Espressif Systems 76 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 18: Charging Circuit Diagram (Click to enlarge)
Fig. 19: Battery Management Circuit Diagram (Click to enlarge)
Fig. 20: Microphone Interface Circuit Diagram (Click to enlarge)
Espressif Systems 77 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Microphone Interface
4.1.3 Hardware Revision Details
ESP-VoCat v1.2
• The following pins have been reassigned:
– U1RXD: Changed from IO5 to IO4
– U1TXD: Changed from IO6 to IO5
– I2S_DI: Changed from IO15 to IO3
– PA_CTRL: Changed from IO4 to IO15
– LCD_RST_CTRL: Changed from IO3 to IO47
• TOUCH interface increased from 1 to 2 for sliding touch sensing:
– TOUCH_PAD1: IO6
– TOUCH_PAD2: IO7
• Added CODEC power control:
– CODEC_PWR_CTRL: IO48
• Added IIC expansion interface:
– Added HC-1.25-4PLT interface: Exposes VIN, I2C_SDA, I2C_SCL, and GND
ESP-VoCat v1.0
• Initial Release
4.1.4 Related Documents
• ESP-VoCat V1.2 Schematic (PDF)
• ESP-VoCat V1.2 PCB Layout (PDF)
• Display Specification (PDF)
• ESP-VoCat Built-in Firmware User Guide (HTML)
ESP-VoCat v1.0
Note: Please check the silkscreen version number on the mainboard to confirm your development board version. For v1.0 version development boards, please refer to the current user guide; for v1.2 version development boards, please refer to ESP-VoCat v1.2.
Tip: For quick-start procedures after powering on ESP-VoCat, refer to the ESP-VoCat Built-in Firmware User Guide.
This guide will help you get started with ESP-VoCat quickly and provide detailed information about this development board. ESP-VoCat is an intelligent AI development kit. It is suitable for voice interaction products that require large model capabilities, such as toys, smart speakers, and smart central control systems. The device is equipped with an ESP32- S3-WROOM-1 module, a 1.85-inch QSPI circular touch screen, dual microphone array, and supports offline voice wake-up and sound source localization algorithms. Combined with the large model capabilities provided by Amazon Nova, OpenAI, Xiaozhi AI, Gemini, etc. ESP-VoCat can achieve full-duplex voice interaction, multimodal recog- nition, and intelligent agent control, providing a solid foundation for developers to create complete edge-side AI application experiences.
Espressif Systems 78 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
ESP-VoCat s main controller uses the Espressif ESP32-S3-WROOM-2-N32R16V module, supporting 2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity. For storage, the entire device has 16 MB PSRAM and 32 MB Flash storage space, and is also equipped with a microSD card slot that can support up to 32 GB, meeting the needs of voice interaction and multimedia processing. It features a 1.85-inch circular touch screen (360 × 360 resolution) with ESP32-S3 native touch sensors, providing an intuitive and rich interactive experience. For audio, ESP-VoCat has a built-in 3W speaker and dual microphone array, supporting local voice wake-up and sound source localization. The power system is compatible with 5 V DC and 3.7 V lithium battery power supply. Additionally, it integrates a USB-C interface for power supply and programming download, while reserving a Pogopin interface for convenient functional expansion.
Fig. 21: ESP-VoCat Front View (Click to enlarge)
The document consists of the following major sections: • Getting Started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: Hardware revision history and known issues (if any) of the board. • Related Documents: Links to related documentation.
Getting Started This section provides a brief introduction of ESP-VoCat, instructions on how to do the initial hardware setup and how to flash firmware onto it.
Description of Components The following introduces the main components on the front PCB in clockwise order. For user convenience, we have also labeled these components or interfaces on the ESP-VoCat housing.
Espressif Systems 79 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 22: ESP-VoCat Back View (Click to enlarge)
Fig. 23: ESP-VoCat CoreBoard PCB Front View (Click to enlarge)
Espressif Systems 80 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 24: ESP-VoCat MicBoard PCB Front View (Click to enlarge)
Fig. 25: ESP-VoCat BaseBoard PCB Front View (Click to enlarge)
Espressif Systems 81 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 26: ESP-VoCat Front View (Click to enlarge)
Main Components Description CoreBoard ESP32-S3-WROOM-2- Main controller chip, integrates 32 MB Flash and 16 MB PSRAM, supports N32R16V 2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity. Battery Connector Battery connector for connecting 3.7 V lithium battery, top is positive, bottom is negative. LCD FPC Connector For connecting 1.85-inch circular LCD screen with 360 x 360 resolution. For detailed parameters, please refer to the Display Specification. MicBoard Connector MicBoard PCB connector, connects dual microphone array and status indicator LED. Touch Connector Touch connector for connecting touch copper foil to achieve touch interaction functionality. Speaker Connector 2-wire speaker connector for connecting built-in 3 W speaker. MicBoard Green LED Green LED indicator. MIC (Microphone Array) Dual LMA3729T381-OY3S microphone array, supports local voice wake-up and sound source localization functionality. BaseBoard BQ27220 (Battery Manage- Battery management chip for battery level detection, charging management, ment Chip) and power status monitoring. TP4057 (Lithium Battery Lithium battery charging chip for charging lithium batteries with 250 mA Charging Chip) charging current. CoreBoard Connector CoreBoard PCB connector, connects core board with base board. TlV62569 (DCDC Chip) Buck converter chip for converting 5 V power to 3.3 V power, providing stable power supply for the system. SAM8108 (Power Control Power control chip for controlling device power on/off. Single click of POWER Chip) button can toggle power on/off status. Type-C (USB-C Interface) USB-C interface for power supply, programming download, and debugging, supports charging lithium batteries. Espressif Systems 82 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 27: ESP-VoCat CoreBoard PCB Back View (Click to enlarge)
Fig. 28: ESP-VoCat MicBoard PCB Back View (Click to enlarge)
The following introduces the main components on the back PCB in clockwise order. For user convenience, we have also labeled these components or interfaces on the ESP-VoCat housing.
Espressif Systems 83 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 29: ESP-VoCat BaseBoard PCB Back View (Click to enlarge)
Fig. 30: ESP-VoCat Back View (Click to enlarge)
Espressif Systems 84 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Main Components Description CoreBoard NS4150B (Class D Amplifier) Ultra-low EMI, filterless, 3W mono Class D audio amplifier. ES7210 (Audio Decoder Chip) High-performance 4-channel audio decoder chip, supports I2S/PDM/TDM data ports. BaseBoard Connector Base board connector for connecting base board with CoreBoard. BMI270 (IMU - Inertial Mea- 6-axis intelligent low-power inertial measurement unit for high-performance surement Unit) applications. ES8311 (Audio Codec Chip) Low-power mono audio codec with high-performance multi-bit Delta-Sigma audio ADC and DAC. MicBoard FPC Connector Connects MicBoard with CoreBoard FPC connector. BaseBoard M1.6 Welded Nut For fixing main board to housing. RST Button (Reset Button) For resetting the main board. Magnetic Connector For functional expansion, provides a serial port and 5 V power interface, can connect to rotating base and other devices. POWER Switch For controlling device power on/off. Single click of POWER button can toggle power on/off status. BOOT Button When powering on, hold this button to enter download mode. SD Card Slot Supports up to 32 GB microSD card slot for storing audio, images, videos, and other data.
Start Application Development Before powering on, please ensure ESP-VoCat is intact and undamaged.
Required Hardware • ESP-VoCat • USB data cable • Computer (Windows, Linux, or macOS)
Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Hardware Setup Use a USB data cable to connect ESP-VoCat to your computer through the Type-C (USB-C Interface) for firmware burning, debugging, and power supply.
Software Setup Please proceed to ESP-IDF Get Started to set up the development environment and flash an ap- plication example onto your board.
Note: In most cases, USB drivers required to operate the board are already included in Windows, Linux, and macOS operating systems. Some additional port access or security configuration may be required depending on your OS. In case of issues, please check documentation on how to establish serial connection with the board. The documentation also includes links to USB drivers applicable to boards produced by Espressif.
Espressif provides Board Support Packages (BSPs) for various Espressif boards that help you initialize and use key onboard peripherals, such as LCD displays, audio chips, buttons, and LEDs, more easily and efficiently. For a com- plete list of supported boards, please visit esp-bsp. Development board application examples are stored in the esp-brookesia project.
Espressif Systems 85 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Hardware Reference
Block Diagram The block diagram below shows the components of ESP-VoCat and their interconnections.
Fig. 31: ESP-VoCat Block Diagram (Click to enlarge)
Power Supply Options There are three mutually exclusive ways to provide power to the board:
Power through Type-C (USB-C Interface) When using this method, connect the device s Type-C interface using a USB Type-C data cable. If a lithium battery is installed, you need to press the POWER button to enable power supply to the device.
Power through Magnetic Connector When using this method, connect the device to the corresponding magnetic connector base to power the device. If a lithium battery is installed, you need to press the POWER button to enable power supply to the device.
Power through Battery The device has an integrated 3.7 V lithium battery. Press the POWER button to power the device. Any of the above external power supply methods can charge the internal lithium battery.
Type-C Interface
Magnetic Connector Interface
LCD Interface Please note that the CN3 interface is reserved for other screen compatibility and is currently not enabled. The U2 interface is the officially used LCD screen interface. The screen model used by this development board is ST77916, LCD: 1.85 , 360 x 360, ST77916, QSPI Interface. LCD_BLK (GPIO44) can be used to control screen backlight.
SD Card Interface Please note that the SD card interface supports: • 1-wire SD bus configuration • Communication through SDIO protocol
Espressif Systems 86 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 32: Magnetic Connector (Click to enlarge)
Fig. 33: Type-C Interface Circuit Diagram (Click to enlarge)
Fig. 34: Magnetic Connector Interface Circuit Diagram (Click to enlarge)
Espressif Systems 87 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 35: LCD Interface Circuit Diagram (Click to enlarge)
Fig. 36: SD Card Interface Circuit Diagram (Click to enlarge)
Fig. 37: Power Switch Circuit Diagram (Click to enlarge)
Espressif Systems 88 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Power Switch Circuit
Fig. 38: Charging Circuit Diagram (Click to enlarge)
Fig. 39: Battery Management Circuit Diagram (Click to enlarge)
Charging Circuit
Microphone Interface
Hardware Revision Details No historical versions.
Related Documents • ESP-VoCat V1.0 Schematic (PDF) • ESP-VoCat V1.0 PCB Layout (PDF) • Display Specification (PDF) • Replication Tutorial (HTML) • ESP-VoCat Built-in Firmware User Guide (HTML)
Espressif Systems 89 Release master Submit Document Feedback
Chapter 4. ESP-VoCat
Fig. 40: Microphone Interface Circuit Diagram (Click to enlarge)
Espressif Systems 90 Release master Submit Document Feedback
Chapter 5
ESP-DualKey
ESP-DualKey is an intelligent dual-key controller development board based on the ESP32-S3 chip developed by Espressif. It integrates smart home control, Bluetooth keyboard, USB keyboard, and other functions, and can switch between different working modes through physical switches. The development board features dual buttons, RGB lighting effects, battery management, power monitoring, and other functions, providing developers with a complete intelligent button solution. Application examples for the development board are stored in the Examples folder.
5.1 ESP-DualKey
Note: Please check the silkscreen version number on the main board to confirm your development board version.
This user guide will help you get started with ESP-DualKey and will also provide more in-depth information. ESP-DualKey is an intelligent dual-key controller development board developed by Espressif based on the ESP32-S3 chip, integrating smart home control, Bluetooth keyboard, USB keyboard and other functions. It can switch between different working modes through physical switches. The development board is equipped with dual buttons, RGB lighting effects, battery management, power monitoring and other functions, providing developers with a complete intelligent button solution. The ESP-DualKey main controller uses the Espressif ESP32-S3 chip, supporting 2.4 GHz Wi-Fi and Bluetooth 5 (LE) wireless connectivity. In terms of storage, the entire device has 8 MB flash storage space to meet the needs of intelligent button applications. It is equipped with a dual-button matrix and WS2812 RGB lighting effects, providing an intuitive and rich interactive experience. In terms of power supply, ESP-DualKey supports USB-C power supply and built-in lithium battery power supply, integrating battery management chips and power monitoring functions. In addition, it also integrates a USB-C in- terface that supports power supply and programming download, while providing multiple working mode switching functions. The document consists of the following major sections: • Getting Started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board s hardware. • Hardware Revision Details: Hardware revision history and known issues (if any) of the board. • Related Documents: Links to related documentation.
91
Chapter 5. ESP-DualKey
Fig. 1: ESP-DualKey Front View (Click to enlarge)
Note: For instructions on using the factory firmware, please refer to ESP-DualKey User Guide.
5.1.1 Getting Started
This section provides a brief introduction of ESP-DualKey, instructions on how to do the initial hardware setup and how to flash firmware onto it.
Feature List
The main features of the board are listed below: Button Matrix Configuration: • 2×1 matrix configuration • Supports independent button detection • Supports combination button functions RGB LED Features: • WS2812 programmable RGB LED • Supports multiple lighting effect modes • Supports brightness, hue, and saturation adjustment Mode Switch: • Left Position: Bluetooth keyboard mode • Middle Position: USB keyboard mode • Right Position: Smart home mode (ESP RainMaker)
Description of Components
The key components of the board are described below. For user convenience, the components or interfaces are also labeled on the housing of ESP-DualKey.
Espressif Systems 92 Release master Submit Document Feedback
Chapter 5. ESP-DualKey
Key Component Description Main Controller ESP32-S3 Main controller chip supporting 2.4 GHz Wi-Fi and Bluetooth 5 (LE) connec- tivity, and featuring 8 MB of integrated flash storage. Interaction Dual Buttons 2×1 button matrix, supports independent key detection and combination key functions. Mode Switch Three-position switch for toggling between operating modes (Bluetooth keyboard/Wi-Fi Mode/USB keyboard). RGB Lighting WS2812 RGB LED Programmable RGB LED supporting diverse lighting effects, e.g., heat map, breathing effect, flowing effect. Power Management Lithium Battery Charging Chip TP4057 lithium battery charging management, supports USB-C charging. Interfaces USB-C Port USB-C for power, programming/download, debugging, and battery charging. Two HY2.0-4P Ports Support auxiliary power output for connecting external sensors. Other Components Battery Voltage Monitoring Real-time battery voltage and charging status monitoring. VBUS Monitoring Monitors USB power status. Deep-sleep Supports Deep-sleep mode for energy saving.
Application Examples
The following application examples are available for ESP-DualKey: • ESP-DualKey Smart Button Controller Example - Demonstrates the use of the ESP-DualKey development board as a smart button controller with smart home control, Bluetooth keyboard, and USB keyboard function- alities, allowing for mode switching through physical switches. • test_apps - Provides unit tests for the esp_hid component on ESP32 and ESP32-C3 chips, allowing developers to validate the functionality of their code and add new test cases as needed. For more examples and the latest updates, please refer to the examples folder. To explore the application examples or to develop your own, please follow the steps outlined in the Start Developing Applications section.
Start Developing Applications
Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.
Required Hardware • ESP-DualKey • USB 2.0 cable (Standard-A to Type-C) • Computer running Windows, Linux, or macOS
Note: Please ensure you use an appropriate USB data cable. Some cables can only be used for charging and cannot be used for data transmission and programming.
Hardware Setup Connect ESP-DualKey with the computer using a USB data cable through the USB-C inter- face for firmware flashing, debugging and power supply.
Espressif Systems 93 Release master Submit Document Feedback
Chapter 5. ESP-DualKey
Software Setup Please proceed to ESP-IDF Get Started to set up the development environment and flash an ap- plication example onto your board.
Note: In most cases USB drivers required to operate the board are already included in Windows, Linux, and macOS operating systems. Some additional port access or security configuration may be required depending on your OS. In case of issues please check documentation on how to establish serial connection with the board. The documentation also includes links to USB drivers applicable to boards produced by Espressif.
Espressif provides Board Support Packages (BSPs) for various Espressif boards that help you initialize and use key onboard peripherals, such as LCD displays, audio chips, buttons, and LEDs, more easily and efficiently. For a com- plete list of supported boards, please visit esp-bsp.
5.1.2 Hardware Reference
Block Diagram
The block diagram below shows the components of ESP-DualKey and their interconnections.
Fig. 2: ESP-DualKey Functional Block Diagram (Click to enlarge)
Power Supply Options There are two mutually exclusive ways to provide power to the board:
- Through USB-C interface power supply When using this method for power supply, use a USB Type-C data cable to connect to the USB-C interface on the device.
- Through built-in lithium battery power supply The device has an integrated lithium battery inside, supporting independent power supply operation.
Mode Switch Circuit The mode switch circuit diagram of the board is shown below.
Espressif Systems 94 Release master Submit Document Feedback
Chapter 5. ESP-DualKey
Fig. 3: Mode Switch Circuit Diagram (Click to enlarge)
5.1.3 Hardware Revision Details
This is the first revision of this board released.
5.1.4 Related Documents
• ESP-DualKey Schematic (PDF)
• User Guide (HTML)
Espressif Systems 95 Release master Submit Document Feedback
Chapter 5. ESP-DualKey
Espressif Systems 96 Release master Submit Document Feedback
Chapter 6
EOL (End of Life) Boards
This section contains user guides for the ESP32-S3 end-of-life development boards and is provided for reference only. While these boards may still be available on the market or used in legacy systems, they no longer receive updates, bug fixes, or official support. It is recommended to switch to newer development boards for better performance and more features.
6.1 ESP32-S3-DevKitM-1
Note: As the ESP32-S3-DevKitM-1 development board offers essentially the same functionality and applications as ESP32-S3-DevKitC-1-N8R8 and ESP32-S3-DevKitC-1U-N8R8, its production has been discontinued. Developers may use ESP32-S3-DevKitC-1-N8R8 or ESP32-S3-DevKitC-1U-N8R8 for software and basic function testing (refer to ESP32-S3-DevKitC-1 User Guide). This change does not affect the supply of the ESP32-S3-MINI-1/1U modules used on the board.
The ESP32-S3-DevKitM-1 is an entry-level development board equipped with either ESP32-S3-MINI-1 or ESP32- S3-MINI-1U, a module named for its small size. This board integrates complete Wi-Fi and Bluetooth® Low Energy functions. Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitM-1 on a breadboard.
6.1.1 ESP32-S3-DevKitM-1
Note: As the ESP32-S3-DevKitM-1 development board offers essentially the same functionality and applications as ESP32-S3-DevKitC-1-N8R8 and ESP32-S3-DevKitC-1U-N8R8, its production has been discontinued. Developers may use ESP32-S3-DevKitC-1-N8R8 or ESP32-S3-DevKitC-1U-N8R8 for software and basic function testing (refer to ESP32-S3-DevKitC-1 User Guide). This change does not affect the supply of the ESP32-S3-MINI-1/1U modules used on the board.
This user guide will help you get started with ESP32-S3-DevKitM-1 and will also provide more in-depth information. The ESP32-S3-DevKitM-1 is an entry-level development board equipped with either ESP32-S3-MINI-1 or ESP32- S3-MINI-1U, a module named for its small size. This board integrates complete Wi-Fi and Bluetooth® Low Energy functions.
97
Chapter 6. EOL (End of Life) Boards
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitM-1 on a breadboard.
Fig. 1: ESP32-S3-DevKitM-1 with ESP32-S3-MINI-1 Module
The document consists of the following major sections: • Getting Started: Overview of the board and hardware/software setup instructions to get started. • Hardware Reference: More detailed information about the board s hardware. • Related Documents: Links to related documentation.
Getting Started
This section provides a brief introduction of ESP32-S3-DevKitM-1, instructions on how to do the initial hardware setup and how to flash firmware onto it.
Description of Components The key components of the board are described in a counter-clockwise direction, starting from the ESP32-S3-MINI-1/1U module.
Espressif Systems 98 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Fig. 2: ESP32-S3-DevKitM-1 - front
Key Component Description ESP32-S3-MINI-1/1U ESP32-S3-MINI-1 and ESP32-S3-MINI-1U are two general-purpose Wi-Fi and Bluetooth Low Energy combo modules that have a rich set of peripherals. ESP32-S3-MINI-1 comes with a PCB antenna. ESP32-S3-MINI-1U comes with an external antenna connector. At the core of the modules is ESP32- S3FN8, a chip equipped with an 8 MB flash. Since flash is packaged in the chip, rather than integrated into the module, ESP32-S3-MINI-1/1U has a smaller package size. 5 V to 3.3 V LDO Power regulator that converts a 5 V supply into a 3.3 V output. Pin Headers All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming. For details, please see Header Block. USB-to-UART Port A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB- to-UART bridge. Boot Button Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port. Reset Button Press this button to restart ESP32-S3. ESP32-S3 USB Port ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 speci- fication. The interface is used for power supply to the board, for flashing appli- cations to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging. USB-to-UART Bridge Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps. RGB LED Addressable RGB LED, driven by GPIO48. 3.3 V Power On LED Turns on when the USB power is connected to the board.
Start Application Development Before powering up your board, please make sure that it is in good condition with no obvious signs of damage.
Required Hardware
Espressif Systems 99 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
• ESP32-S3-DevKitM-1
• USB 2.0 cable (Standard-A to Micro-B)
• Computer running Windows, Linux, or macOS
Note: Be sure to use an appropriate USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.
Hardware Setup Connect the board with the computer using USB-to-UART Port or ESP32-S3 USB Port. In subsequent steps, USB-to-UART Port will be used by default.
Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel- opment environment and then flash an application example onto your board.
Contents and Packaging
Retail Orders If you order a few samples, each board comes in an individual package in either antistatic bag or any packaging depending on your retailer. For retail orders, please go to https://www.espressif.com/en/contact-us/get-samples.
Wholesale Orders If you order in bulk, the boards come in large cardboard boxes. For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.
Hardware Reference
Block Diagram The block diagram below shows the components of ESP32-S3-DevKitM-1 and their interconnec- tions.
Fig. 3: ESP32-S3-DevKitM-1 (click to enlarge)
Espressif Systems 100 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Power Supply Options There are three mutually exclusive ways to provide power to the board: • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended) • 5V and G (GND) pins • 3V3 and G (GND) pins
Header Block The two tables below provide the Name and Function of the pins on both sides of the board (J1 and J3). The pin names are shown in ESP32-S3-DevKitM-1 - front. The numbering is the same as in the Board Schematic (PDF).
J1
No. Name Type1 Function 1 3V3 P 3.3 V power supply 2 0 I/O/T RTC_GPIO0, GPIO0 3 1 I/O/T RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0 4 2 I/O/T RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1 5 3 I/O/T RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2 6 4 I/O/T RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3 7 5 I/O/T RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4 8 6 I/O/T RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5 9 7 I/O/T RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6 10 8 I/O/T RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1 11 9 I/O/T RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD, SUBSPIHD 12 10 I/O/T RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4, SUB- SPICS0 13 11 I/O/T RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5, SUBSPID 14 12 I/O/T RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6, SUB- SPICLK 15 13 I/O/T RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7, SUBSPIQ 16 14 I/O/T RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS, SUB- SPIWP 17 15 I/O/T RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P 18 16 I/O/T RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N 19 17 I/O/T RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6 20 18 I/O/T RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3 21 5V P 5 V power supply 22 G G Ground
1 P: Power supply; I: Input; O: Output; T: High impedance.
Espressif Systems 101 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
J3
No. Name Type Function
1 G G Ground
2 RST I EN
3 46 I/O/T GPIO46
4 45 I/O/T GPIO45
5 RX I/O/T U0RXD, GPIO44, CLK_OUT2
6 TX I/O/T U0TXD, GPIO43, CLK_OUT1
7 42 I/O/T MTMS, GPIO42
8 41 I/O/T MTDI, GPIO41, CLK_OUT1
9 40 I/O/T MTDO, GPIO40, CLK_OUT2
10 39 I/O/T MTCK, GPIO39, CLK_OUT3, SUBSPICS1
11 38 I/O/T GPIO38, FSPIWP, SUBSPIWP
12 37 I/O/T SPIDQS, GPIO37, FSPIQ, SUBSPIQ
13 36 I/O/T SPIIO7, GPIO36, FSPICLK, SUBSPICLK
14 35 I/O/T SPIIO6, GPIO35, FSPID, SUBSPID
15 34 I/O/T SPIIO5, GPIO34, FSPICS0, SUBSPICS0
16 33 I/O/T SPIIO4, GPIO33, FSPIHD, SUBSPIHD
17 26 I/O/T SPICS1, GPIO26
18 21 I/O/T RTC_GPIO21, GPIO21
19 20 I/O/T RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
20 19 I/O/T RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
21 48 I/O/T SPICLK_N, GPIO48, SUBSPICLK_N_DIFF, RGB LED
22 47 I/O/T SPICLK_P, GPIO47, SUBSPICLK_P_DIFF
For description of function names, please refer to ESP32-S3 Datasheet (PDF).
Fig. 4: ESP32-S3-DevKitM-1 Pin Layout (click to enlarge)
Pin Layout
Espressif Systems 102 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Hardware Revision Details
This is the first revision of this board released.
Related Documents
• ESP32-S3 Datasheet (PDF)
• ESP32-S3-MINI-1 & ESP32-S3-MINI-1U Datasheet (PDF)
• ESP32-S3-DevKitM-1 Schematic (PDF)
• ESP32-S3-DevKitM-1 PCB layout (PDF)
• ESP32-S3-DevKitM-1 Dimensions (PDF)
• ESP32-S3-DevKitM-1 Dimensions source file (DXF) - You can view it with Autodesk Viewer online
• ESP32-S3-DevKitM-1 Reference Design (ZIP)
For further design documentation for the board, please contact us at sales@espressif.com.
6.2 ESP32-S3-USB-Bridge
ESP32-S3-USB-Bridge can act as an alternative to USB-to-UART chips like CP210x or debuggers by establishing a bridge between the computer and existing microcontrollers.
6.2.1 ESP32-S3-USB-Bridge
This user guide will help you get started with ESP32-S3-USB-Bridge and will also provide more in-depth information. The document consists of the following sections: • Board Overview: Overview of the board hardware/software • Start Application Development: How to set up hardware/software to develop applications • Hardware Reference: More detailed information about the board s hardware • Hardware Revision Details: This is the first revision of this board released • Sample Request: How to get a sample board • Related Documents: Links to related documentation
Board Overview
ESP32-S3-USB-Bridge is a development board based on ESP32-S3. • The usb_wireless_bridge example can be used to establish a bridge between a computer and the target chip. It can emulate a USB composite device and supports multiple functions: – USB-to-UART Bridge: realizes serial data transmission and reception between the computer and the target chip. – JTAG Adapter: realizes duplex JTAG communication between the computer and the target chip. – MSC Storage Device: updates firmware by storing the UF2 firmware files in the USB storage device of the board. – Wireless Bridge: realizes wireless flashing and wireless serial data transmission and reception through ESP-NOW. The development board also supports a USB Type-A interface that is convenient for replacement.
Espressif Systems 103 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Fig. 5: ESP32-S3-USB-Bridge Type-C Connection
Fig. 6: ESP32-S3-USB-Bridge Type-A Connection
Espressif Systems 104 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Feature List The main features of the board are listed below: • Module Embedded: ESP32-S3-MINI-1 module with 4 MB flash and 2 MB PSRAM • LED Indicators: on-board WS2812 LED indicator with two serial data LED indicators • USB: on-board USB-to-UART bridge and JTAG adapter, with support for USB download/debugging
Block Diagram The block diagram below shows the components of ESP32-S3-USB-Bridge and their intercon- nections.
Fig. 7: ESP32-S3-USB-Bridge Block Diagram (Click to Enlarge)
Description of Components ESP32-S3-USB-Bridge is a rather compact development board, with a dimension of 23.3 mm * 31.5 mm. It integrates the ESP32-S3-MINI-1 module and offers a 12-pin expansion connector. The key components of the board are described in a clockwise direction.
Key Component Description ESP32-S3-MINI-1-N4R2 ESP32-S3-MINI-1-N4R2 is a generic Wi-Fi + Bluetooth LE MCU module Module that is built around the ESP32-S3 series of SoCs. It is integrated with 4 MB flash and 2 MB PSRAM. On top of a rich set of peripherals, the acceleration for neural network computing and signal processing workloads provided by the SoC makes the module an ideal choice for a wide variety of application sce- narios related to Artificial Intelligence of Things (AIoT). TX/RX Indicator Indicates transmit and receive status of serial data. Expansion Connector Provides connections for JTAG pins, serial pins, TX/RX pins, Boot pins, Reset pins, and power supply pins. Reset Button Connects the Reset button on the target chip and IO8 on the module. Press this button to reset the target chip. USB-to-USB Port Provides power to the entire system. Used for USB communication between the PC and the ESP32-S3-MINI-1 module. Boot Button Connects the Boot button on the target chip and IO9 on the module. Holding down the Boot button and momentarily pressing the Reset button initiates the firmware upload mode. Then you can upload firmware through the serial port or USB.
Espressif Systems 105 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Fig. 8: ESP32-S3-USB-Bridge - Front (Click to Enlarge)
Fig. 9: ESP32-S3-USB-Bridge - Back (Click to Enlarge)
Espressif Systems 106 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Key Component Description 5 V to 3.3 V Converts the USB voltage to 3.3 V for powering the ESP32-S3-MINI-1 mod- ule. Module Boot Button Connects IO0 on the module. After holding down the Boot button and power- ing up the development board again, the board enters the download mode and initiates the firmware upload mode for uploading firmware. WS2812 Connects IO42 on the module and indicates the current state of the development board.
Software Support Development of applications for ESP32-S3-USB-Bridge can be done using ESP-IDF frame- work. ESP-IDF is a FreeRTOS-based SoC development framework with several components including LCD, ADC, RMT, and SPI. An example is provided for ESP32-S3-LCD-EV-Board under the folder Examples . You can config- ure project options by entering idf.py menuconfig in the example directory.
Note: • The current supported ESP-IDF version is release/5.0. • To prevent the default firmware from being replaced, please avoid pressing and holding the module s own Boot button while powering the board up/down.
Start Application Development
This section provides instructions on how to do hardware and software setup and flash firmware onto the board to develop your own application.
Required Hardware • 1 x ESP32-S3-USB-Bridge • 1 x LCD subboard • 1 x USB 2.0 cable (standard Type-A to Type-C) • 1 x PC (Windows, Linux, or macOS)
Note: Please make sure to use the appropriate USB cable. Some cables can only be used for charging, not for data transfer or program flashing.
Hardware Setup Prepare the board for loading of the first sample application:
- Plug in the USB cable to connect the PC with the USB port on the board.
- Make sure the board is in the download mode.
- The LED lights up indicating the completion of flashing. Now the board is ready for software setup.
Software Setup Please proceed to Get Started, where Section Installation will quickly help you set up the devel- opment environment. For more software information on developing applications, please go to Software Support.
Hardware Reference
This section provides more detailed information about the board s hardware.
Espressif Systems 107 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
GPIO Allocation The table below provides the GPIO allocation of the ESP32-S3-MINI-1 module and its 12-pin expansion connector, which is used to control specific components or functions on the development board as well as the externally connected target chip.
Table 1: ESP32-S3-MINI-1 and Expansion Connector GPIO Allocation
Pin Pin Name Function 1 GND GND 2 3V3 Power supply 3 IO0 Module boot button for entering download mode which can also be used as a key input pin 4 IO2 JTAG pin TDO for test data output 5 IO3 JTAG pin TDI for test data input 6 IO4 JTAG pin TCK for synchronized test data transfer 7 IO5 JTAG pin TMS for test mode configuration 8 IO8 The Reset pin connecting to the target chip, which sets the target chip to low level when pressed 9 IO9 The Boot pin connecting to the target chip, which sets the tar- get chip to low level when pressed 10 IO19 USB_D- 11 IO20 USB_D+ 12 IO40 RX connecting to the UART TX pin of the target chip 13 IO41 TX connecting to the UART RX pin of the target chip 14 IO42 WS2812 control pin
Note: Pin 3 to Pin 14 are the corresponding pins of the 12-pin expansion connector. Apart from the features in the above table, all these IO pins support to be configured for other purposes. Note that GPIO5 and GPIO8 should be connected to external keys.
Power Distribution
Power Supply over USB There are two ways to power the development board via the USB power port: • Via the Type-A port
Fig. 10: ESP32-S3-USB-Bridge - Type-A Power Supply
• Via the Type-C port
Voltage Conversion Circuit The ESP32-S3-USB-Bridge supports converting 5 V to 3.3 V for the module.
Espressif Systems 108 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Fig. 11: ESP32-S3-USB-Bridge - Type-C Power Supply
Fig. 12: ESP32-S3-USB-Bridge - Voltage Conversion
Espressif Systems 109 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Hardware Setup Options
Automatic Download Press the Boot button on the module and re-power up the board, then release the Boot button to allow the board to enter the download mode.
Hardware Revision Details
No previous revisions.
Sample Request
This board has been open-sourced to OSHWHub. Please sample it according to your needs.
Related Documents
Please download the following documents from the HTML version of esp-dev-kits Documentation. • ESP32-S3 Datasheet • ESP32-S3-MINI-1 Datasheet • ESP Product Selector • ESP32-S3-USB-Bridge PCB Layout • ESP32-S3-USB-Bridge Schematics For further design documentation for the board, please contact us at sales@espressif.com.
Espressif Systems 110 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
ESP32-S3 Development Boards
ESP32-S3-DevKitC-1 ESP32-S3-USB-OTG
ESP32-S3-LCD-EV-Board ESP-VoCat
ESP-DualKey
Espressif Systems 111 Release master Submit Document Feedback
Chapter 6. EOL (End of Life) Boards
Espressif Systems 112 Release master Submit Document Feedback
Chapter 7
Related Documentation and Resources
7.1 Related Documentation • ESP32-S3 Datasheet Specifications of the ESP32-S3 hardware. • ESP32-S3 Technical Reference Manual Detailed information on how to use the ESP32-S3 memory and pe- ripherals. • ESP32-S3 Hardware Design Guidelines Guidelines on how to integrate the ESP32-S3 into your hardware product. • ESP32-S3 Product/Process Change Notifications (PCN) https://espressif.com/en/support/documents/pcns?keys=ESP32-S3 • ESP32-S3 Advisories Information on security, bugs, compatibility, component reliability. https://espressif.com/en/support/documents/advisories?keys=ESP32-S3 • Certificates https://espressif.com/en/support/documents/certificates • Documentation Updates and Update Notification Subscription https://espressif.com/en/support/download/documents
7.2 Developer Zone • ESP-IDF Programming Guide for ESP32-S3 Extensive documentation for the ESP-IDF development frame- work. • ESP-IoT-Solution Programming Guide - Extensive documentation for the ESP-IoT-Solution development framework. • ESP-FAQ - A summary document of frequently asked questions released by Espressif. • ESP-IDF and other development frameworks on GitHub. https://github.com/espressif • ESP32 BBS Forum Engineer-to-Engineer (E2E) Community for Espressif products where you can post ques- tions, share knowledge, explore ideas, and help solve problems with fellow engineers. https://esp32.com/ • The ESP Journal Best Practices, Articles, and Notes from Espressif folks. https://blog.espressif.com/ • See the tabs SDKs and Demos, Apps, Tools, AT Firmware. https://espressif.com/en/support/download/sdks-demos
113
Chapter 7. Related Documentation and Resources
7.3 Products • ESP32-S3 Series SoCs Browse through all ESP32-S3 SoCs. https://espressif.com/en/products/socs?id=ESP32-S3 • ESP32-S3 Series Modules Browse through all ESP32-S3-based modules. https://espressif.com/en/products/modules?id=ESP32-S3 • ESP32-S3 Series DevKits Browse through all ESP32-S3-based devkits. https://espressif.com/en/products/devkits?id=ESP32-S3 • ESP Product Selector Find an Espressif hardware product suitable for your needs by comparing or applying filters. https://products.espressif.com/#/product-selector
7.4 Contact Us • See the tabs Sales Questions, Technical Enquiries, Circuit Schematic & PCB Design Review, Get Samples (Online stores), Become Our Supplier, Comments & Suggestions. https://espressif.com/en/contact-us/sales-questions
Espressif Systems 114 Release master Submit Document Feedback
Chapter 8
Disclaimer and Copyright Notice
Information in this document, including URL references, is subject to change without notice. All third party s information in this document is provided as is with no warranties to its authenticity and accuracy. No warranty is provided to this document for its merchantability, non-infringement, fitness for any particular purpose, nor does any warranty otherwise arising out of any proposal, specification or sample. All liability, including liability for infringement of any proprietary rights, relating to use of information in this doc- ument is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are granted herein. The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is a registered trademark of Bluetooth SIG. All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged.
115
Use this datasheet from any agent
Send the page, markdown, chunks, or search endpoint to ChatGPT, Claude, embedr-app, or your own tooling.
